N-Com B902 Instruction Manual

June 6, 2024
N-Com

N-Com B902

EN

USER INSTRUCTIONS AND SAFETY

Congratulations on your purchase of an N-Com product.
N-Com B902 was made using the most advanced technology and top-quality materials. Long-running tests and thorough system development have made it possible to achieve the highest audio quality.
For additional information on the B902, to download the instructions in PDF format and install the latest available Firmware version, please visit the website www.n-com.it.

Firmware version: 1.0

REFERENCE STANDARDS The products of the N-Com line comply with standards as per the table below:

B902

The Bluetooth system complies with the main safety requirements and other applicable provisions of Directive RED 2014/53/EU, 2011/65/CE

Battery charger

Directive 2014/35/EU LVD, 2014/30/EU EMC, 2009/125/CE ErP, 2011/65/EU RoHS

Battery

Directive 2001/95/CE ­ GPSD, 2013/56/UE – BAT, 1907/2006 ­ REACH, 2014/30/UE ­ EMC, 2011/65/EU – RoHS

The Declarations of Compliance can be downloaded from the website www.n-com.it (Download section).

Model: B902 X PMN: N-Com B902 X

FCC ID: Y6MNCOM22

IC: 9455A-NCOM22

R-NZ

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.; any use of such marks by N-Com is under license. Other trademarks and trade names are those of their respective owners.

Fw 1.0 – 22/12/2020

Contents
1. WARNINGS AND SAFETY………………………………………………………………………………………………………………………………………..3 1.1.Road safety……………………………………………………………………………………………………………………………………………………………………………………… 3 1.2.Switching on the system in safe environments ………………………………………………………………………………………………………………………… 3 1.3.Interferences …………………………………………………………………………………………………………………………………………………………………………………… 3 1.4.Appropriate use……………………………………………………………………………………………………………………………………………………………………………… 3 1.5.Qualified personnel……………………………………………………………………………………………………………………………………………………………………….. 4 1.6.Accessories and batteries …………………………………………………………………………………………………………………………………………………………….. 4 1.7. Disposal …………………………………………………………………………………………………………………………………………………………………………………………. 4
2. CONTENT OF THE PACKAGING………………………………………………………………………………………………………………………………5 3. INSTALLATION ON THE X-1005 AND X-903 HELMET ……………………………………………………………………………………………6
3.1.Preliminary operations ………………………………………………………………………………………………………………………………………………………………….. 6 3.2.Installing the system in the X-1005 and X-903 helmets………………………………………………………………………………………………………….. 6 3.3.Microphone positioning……………………………………………………………………………………………………………………………………………………………….. 8 3.4.Repositioning the padding…………………………………………………………………………………………………………………………………………………………… 9 4. INSTALLATION ON THE X-LITE HELMETS …………………………………………………………………………………………………………… 10 4.1.Preliminary operations …………………………………………………………………………………………………………………………………………………………………10 4.2.Installing the system in the helmet ……………………………………………………………………………………………………………………………………………10 4.3.Microphone positioning………………………………………………………………………………………………………………………………………………………………12 4.4.Repositioning the padding………………………………………………………………………………………………………………………………………………………….13 5. REMOVING THE SYSTEM …………………………………………………………………………………………………………………………………….. 14 6. BASIC FUNCTIONS ………………………………………………………………………………………………………………………………………………. 14 6.1.Volume adjustment………………………………………………………………………………………………………………………………………………………………………14 6.2.Auto On / Off function…………………………………………………………………………………………………………………………………………………………………14 6.3 .Multi-language voice messages…………………………………………………………………………………………………………………………………………………15 6.4.N-Com EASYSET……………………………………………………………………………………………………………………………………………………………………………15 6.5.Updating the firmware…………………………………………………………………………………………………………………………………………………………………15 7. PAIRING UP MENU………………………………………………………………………………………………………………………………………………. 16 8. CONFIGURATION MENU …………………………………………………………………………………………………………………………………….. 16 9. MOBILE PHONE / MP3 PLAYER PAIR UP …………………………………………………………………………………………………………….. 17 10. SECOND MOBILE PHONE PAIR UP ……………………………………………………………………………………………………………………… 17 11. MOBILE PHONE……………………………………………………………………………………………………………………………………………………. 18 11.1.Speed dial…………………………………………………………………………………………………………………………………………………………………………………….18 11.2.Conference call function ……………………………………………………………………………………………………………………………………………………………19 11.3.Smart Navi System……………………………………………………………………………………………………………………………………………………………………..19 12. MUSIC VIA BLUETOOTH………………………………………………………………………………………………………………………………………. 19 12.1.Sharing music via Bluetooth (A2DP Sharing) …………………………………………………………………………………………………………………………20 13. MUSIC VIA CABLE………………………………………………………………………………………………………………………………………………… 20 14. NAVIGATOR PAIR UP…………………………………………………………………………………………………………………………………………… 20 15. FM RADIO…………………………………………………………………………………………………………………………………………………………….. 21 16. AUDIO MULTITASKING………………………………………………………………………………………………………………………………………… 21 16.1.Enabling / disabling the Audio Multitasking function ………………………………………………………………………………………………………….21 16.2.Adjusting the volumes……………………………………………………………………………………………………………………………………………………………….22 17. INTERCOM …………………………………………………………………………………………………………………………………………………………… 22 17.1.N-Com “600”/”900″ Series Intercom pairing up ……………………………………………………………………………………………………………………22 17.2.Pairing up other N-Com ……………………………………………………………………………………………………………………………………………………………23 17.3.Intercom function (one-to-one connection) ………………………………………………………………………………………………………………………….23 17.4.Smart Conference (Group Intercom)……………………………………………………………………………………………………………………………………….24 18. “UNIVERSAL INTERCOM” INTERCOM …………………………………………………………………………………………………………………. 25 18.1.Pairing up the UNIVERSAL INTERCOM……………………………………………………………………………………………………………………………………25 18.2.Universal Intercom Function …………………………………………………………………………………………………………………………………………………….26 18.3.Universal Conference (chain intercom) …………………………………………………………………………………………………………………………………..26 19. REMOTE CONTROL ……………………………………………………………………………………………………………………………………………… 27 20. BATTERY AND RECHARGE …………………………………………………………………………………………………………………………………… 28 20.1.Low battery signal ………………………………………………………………………………………………………………………………………………………………………28 20.2.Checking the Battery Level………………………………………………………………………………………………………………………………………………………..28 20.3.Charging the system ………………………………………………………………………………………………………………………………………………………………….28 21. SUMMARY TABLE OF CONTROLS ……………………………………………………………………………………………………………………….. 29 22. WARRANTY ………………………………………………………………………………………………………………………………………………………….. 30 22.1.Warranty coverage and validity ……………………………………………………………………………………………………………………………………………….30 22.2.Exclusions and limitations of coverage …………………………………………………………………………………………………………………………………..30 22.3.Procedure for submitting claims………………………………………………………………………………………………………………………………………………30 22.4.Product identification ………………………………………………………………………………………………………………………………………………………………..31 22.5.Validity of N-Com warranty………………………………………………………………………………………………………………………………………………………32
2

1. WARNINGS AND SAFETY
Read this User Manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing
tracks and the like. Caution: Installation of the N-Com B902 system results in a weight increase of approximately 120 g, which is
added to the weight of the helmet and of the other accessories. Warning: The electronic components of the N-Com system mounted inside the helmet are not waterproof.
Consequently, make sure the inside of the helmet, including the comfort padding, does not get wet in order to avoid damage to the system. If water seeps into the helmet, remove the comfort padding from the helmet and allow to air dry.
1.1. Road safety
Always obey all Traffic Regulations in force. While riding your motorcycle, your hands should always be engaged in actually riding the vehicle. Any operation to the N-Com system must be carried out with the motorcycle stopped. Specifically: · Set your cell phone on automatic answer (see the cell phone instructions to do this). · If your cell phone is not equipped with this function, first stop your vehicle in a safe area, in compliance
with Traffic Regulations and then answer the call. · Do not make any calls while riding. Stop your vehicle in a safe place in compliance with Traffic
Regulations and then make the call. · Adjust the volume so that it does not cause a disturbance or distraction while riding and at the same time
allows you to distinctively hear background noises. · Do not operate your cell phone or other devices connected to the N-Com system while riding your
motorcycle. · In all cases, obey the Traffic Regulations and remember that riding the motorcycle has absolute priority
over any other manoeuvre.
1.2. Switching on the system in safe environments
· When using the N-Com system, comply with all limitations and instructions related to the use of cell phones.
· Do not turn on your cell phone or the N-Com system whenever their use is forbidden or when these devices can cause interference or dangerous situations.
· Turn off while refuelling. Do not use the N-Com system at filling stations. Do not use the device near combustible materials or chemical products.
· Turn off when near explosive materials.
1.3. Interferences
All phones and devices with wireless signal transmission are subject to interferences that may affect the performance of the device connected to them. These interferences are not ascribable to a defect of the NCom system.
1.4. Appropriate use
Use the device only in the normal position, as described in the product documentation. Do not attempt to disassemble, tamper with, or modify any part of the N-Com system. Caution: Adjust the volume of the N-Com system and of the audio sources connected to it before you use
the system on the road. Caution: Adjusting the volume to exceedingly high levels may cause damage to your hearing. Caution: Incorrect installation of the system in the helmet may alter the aerodynamic and safety
characteristics of the helmet itself, thus creating dangerous conditions. Install the N-Com system
3

EN

according to the instructions provided in the product documentation. In case of doubt, please contact your local N-Com dealer. Warning: Listening to other equipment should not interfere with riding your motorcycle, which must be the top priority at all times. Carry out all operations on the electronic equipment and on the N-Com system with the vehicle stopped, in compliance with Traffic Regulations. Caution: The N-Com system allows reception of the FM radio signal. Any radio licence fees are charged to the user.

1.5. Qualified personnel
Only qualified personnel can carry out technical assistance on this product. In case of any malfunction, always turn to your local dealer. The helmet is a safety device. Tampering with it and/or with the electronic system inside the helmet can result in dangerous situations, in addition to invalidating the product warranty.

1.6. Accessories and batteries
· Only use the type of batteries, battery chargers and accessories approved by Nolangroup for the specific model.
· Using a battery type different from the recommended one may lead to dangerous situations and invalidate the warranty.
· Contact your local dealer to see about the availability of approved accessories. · When disconnecting the power supply cable of any accessory or of the battery charger, always grab and
pull the plug, not the cable. · Do not use batteries for purposes other than the prescribed ones. · Never use batteries or battery chargers that turn out to be damaged. · Do not short-circuit the battery. · Keep the battery at a temperature between 0° / +45°C (charging): -10° / +55°C (in use). · Danger of fire or explosion: do not throw the batteries into a fire or expose them to high temperatures! · Do not throw out batteries together with household refuse. The batteries should be disposed of in
compliance with local regulations. · Do not wear the helmet while the battery is recharging. · The helmet should never be left within the reach of unsupervised children in order to prevent damage to
their health caused by access to the batteries.

Battery Battery charger

603443 W&T-AD1812A050150EU W&T-AD1812A050200KU

LiPo 3.7V ­ 1000 mAh 230V 50Hz 0.35 A ­ 5V 1.5 A 230V 50Hz 0.35 A ­ 5V 2A

1.7. Disposal
Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions:
· The presence of a crossed-out wheelie bin indicates that in the European Union the product is subject to separate collection at the end of its useful life.
· Do not dispose of these products together with undifferentiated urban waste.
· The proper disposal of obsolete equipment contributes to preventing possible negative consequences on people’s health and on the environment.
· Within the European Union, the dealer, when supplying the new equipment, ensures that the used equipment will be collected free of charge, provided it is equivalent to a ratio of one to one.
· For more detailed information on the disposal of obsolete equipment, contact your municipality, a waste disposal service, or the store where the product was purchased.

4

2. CONTENT OF THE PACKAGING The N-Com B902 package contains:

e-box with wiring

Rechargeable battery

Battery charger

Adhesive Keypad

Microphone

Microphone for X-903 helmet

Mini USB jack wire

Flat head tool

Microphone foam

Key, Screw, Microphone securing clip

Microphone securing stickers

Adhesive strips for loudspeakers
5

EN
3. INSTALLATION ON THE X-1005 AND X-903 HELMET The X-1005 and X-903 helmets are pre-set for the EASYFIT simplified installation of the N-Com system.
Important: Prior to installing the N-Com system, it is recommended to write down the identification code affixed to the product (see chapter 22.4).
The installation video can be seen at www.n-com.it / Support section.
3.1. Preliminary operations · Remove the internal comfort padding by following the specific instructions provided in the helmet
user manual, being careful to also remove the size adjustment tab. · Remove from the polystyrene cheek pads the foam material at the housing of the N-Com
earphones. Keep this filling materials should you decide in the future to use the helmet without the N-Com system installed.
3.2. Installing the system in the X-1005 and X-903 helmets · On the left side of the helmet, open the cheek pad lining door (Fig. 1). Remove the filling material.
Keep it in case you want to use your helmet without the N-Com system installed in the future. · Remove the small N-Com cap positioned on the left side of the helmet. To make the operation
easier, we recommend pushing the cap from inside the helmet (Fig. 2). · Thoroughly clean the outside surface of the shell to make sure that the adhesive keypad sticks
properly. Before you apply the keypad, make sure that the shell area is completely clean and grease or dirt free. · Remove the protective film from the back of the adhesive keypad using the special tab (Fig. 3). · Pass the keypad flex through the hole in the outer shell (Fig. 4). · Apply the keypad to the shell and press down on its entire surface to make sure that it sticks properly (Fig. 5).

Fig. 1

Fig. 2

Fig. 3

Fig. 4 6

Fig. 5

N.B.: Make sure you do not glue the keypad flex underneath the keypad support. N.B.: In the event that the keypad is not positioned correctly, peel it off right away with extreme care
and repeat the positioning. N.B.: It takes up to 24 hours for the keypad to stick completely. During this time, do not expose the
helmet to atmospheric agents.
· Line up the keypad flex connector to the e-box making sure that the letter “n” is pointing as shown in Fig. 6.
· Gently position the connector in its seat until it is all the way in (Fig. 7). · Connect the battery to the wiring system (Fig. 8). · Switch on the N-Com system (press “ON” for about 2 seconds) to verity its proper operation.
N.B. If the system does not work, remove the flex and repeat the previous operation, making sure that the “n” is positioned as in Fig. 6.

Fig. 6

Fig. 7

Fig. 8

· Secure the keypad flex in the specials stop (Fig. 9). · Position the e-box in its seat, arranging the keypad flex cable so that it does not interfere with the
positioning of the e-box, as illustrated in figures 10-11-12.

Fig. 9 Fig. 12

Fig. 10 Fig. 13

Fig. 11
· Position the left loudspeaker in its seat, inserting the cable in the special groove. If necessary, secure the earphone using the adhesive supplied as standard equipment (Fig. 13).
7

EN
3.3. Microphone positioning
ONLY FOR X-1005 HELMETS · With the help of the flat head tool supplied as standard equipment, open the microphone-holder
clip located on the right side of the helmet (Fig. 14-15). · Position the microphone at the desired length, sliding the excess portion inside the cheek pad
lining (Fig. 16). N.B.: To ensure good voice transmission quality, it is recommended to adjust the length of the microphone so that the foam part is in front of your mouth. · Close the clip. Make sure that the microphone side with the letter “n” is facing the inside of the helmet (Fig. 17).

Fig. 14

Fig. 15

Fig. 16

Fig. 17

ONLY FOR X-903 HELMETS · Hook up the specific microphone for full-face helmets in its seat in the chin guard (Fig. 18). · Position the microphone wire in the vertical groove (Fig. 19) and afterwards behind the cheek pad
lining. If necessary, lift up the groove tabs and the cheek pad lining using a flat head tool (supplied as standard equipment).

Fig. 18 8

Fig. 19

Fig. 20

Fig. 21

Fig. 22

Fig. 23

Fig. 24 A ­ X-1005 HELMET

Fig. 24 B ­ X-903 HELMET

· Hook up the microphone to the connector coming out of the e-Box (Fig. 20).
· Position the wiring and the connectors behind the cheek pad lining, lifting it with the help of a flat head tool (Fig. 21).
· Pass the USB mini wire through the elastic band found on the comfort padding (Fig. 22).
· Position the wiring and the antenna in the rear part of the helmet (Fig. 23).
· On the right side of the helmet, bend the cheek pad lining and insert the battery in its housing (Fig. 24 A/B – 25). ONLY FOR X-1005 HELMETS: Remove the filling material. Keep it in case you want to use the helmet without the NCom system installed in the future.

Fig. 25

Fig. 26

· Position the right loudspeaker in its housing, inserting the cable in the special groove (Fig. 26). If necessary, secure the earphone using the adhesive supplied as standard equipment.

· Position the wiring and the connectors behind the cheek pad lining, lifting it up with the help of a flat head tool.

3.4. Repositioning the padding Reposition the internal comfort padding by following the specific instructions provided in the helmet user manual. Warning: Always verify the proper length of your chinstrap and adjust it if necessary, referring to the
specific helmet instructions.
9

EN
4. INSTALLATION ON THE X-LITE HELMETS This procedure must be followed for the installation of N-Com systems on X-lite helmets other than model X-1005 and X-903.
Important: Prior to installing the N-Com system, it is recommended to write down the identification code affixed to the product (see chapter 22.4).
The installation video can be seen at www.n-com.it / Support section.
4.1. Preliminary operations · Remove the internal comfort padding by following the specific instructions provided in the helmet
user manual. · If present, remove from the polystyrene cheek pads the foam filling material that cover the
housings of the N-Com earphones. Keep this filling materials should you decide in the future to use the helmet without the N-Com system installed.
4.2. Installing the system in the helmet · Connect the battery to the wiring system (Fig. 27). · Position the battery in the right polystyrene cheek pad housing and secure it using the Velcro
ribbon (Fig. 28). · Position the right-hand side speaker in the specific cheek pad housing and secure it using the
specific adhesive (Fig. 29). · Reposition the right polystyrene cheek pad in its housing. ONLY FOR FULL-FACE HELMETS: Insert the chin strap into the polystyrene cheek pad loop.

Fig. 27
Fig. 30 10

Fig. 28

Fig. 29

· Arrange the battery connector behind the polystyrene cheek pad.
· Position the wiring and the antenna at the back of the helmet (Fig. 30).

ONLY FOR X-702 HELMETS · Cut along the pre-cut lines of the plastic tab on the back of the comfort padding. · Position the wiring underneath the plastic tab (Fig. 31). N.B.: the side parts of the antenna must be positioned above the buttons to allow the correct hooking of the comfort padding (Fig. 32).

Fig. 31

Fig. 32

· Remove the small N-Com cap positioned on the left side of the helmet. To make the operation easier, we recommend pushing the cap from inside the helmet (Fig. 33).
· Thoroughly clean the outside surface of the shell to make sure that the adhesive keypad sticks properly. Before you apply the keypad, make sure that the shell area is completely clean and grease or dirt free.
· Remove the protective film from the back of the adhesive keypad using the special tab (Fig. 34). · Pass the keypad flex through the hole in the outer shell (Fig. 35).

Fig. 33

Fig. 34

Fig. 35

· Apply the keypad to the shell and press down on its entire surface to make sure that it sticks properly (Fig. 36).
Fig. 36
N.B.: Make sure you do not glue the keypad flex underneath the keypad support. N.B.: In the event that the keypad is not positioned correctly, peel it off right away with extreme care
and repeat the positioning. N.B.: It takes up to 24 hours for the keypad to stick completely. During this time, do not expose the
helmet to atmospheric agents.
11

EN
· Line up the keypad flex connector to the e-box making sure that the letter “n” is pointing as shown in Fig. 37.
· Gently position the connector in its seat until it is all the way in (Fig. 38). · Switch on the N-Com system (press “ON” for about 2 seconds) to verity its proper operation.
N.B. If the system does not work, remove the flex and repeat the previous operation, making sure that the “n” is positioned as in Fig. 37.

Fig. 37

Fig. 38

· Secure the keypad flex in the special stop (Fig. 39) and position the e-box inside its housing in the cheek pad (Fig. 40).
· Temporarily reposition the polystyrene cheek pad inside the helmet and continue with the subsequent paragraph.

Fig. 39

Fig. 40

4.3. Microphone positioning
FLIP UP OR JET HELMETS · Insert the microphone securing clip (Fig. 41). · Position the microphone on the left side of the helmet, screwing in the screw in the small shell
frame (Fig. 42). Make sure that the side of the microphone with the caption “n” is facing the inside of the helmet (Fig. 43).

Fig. 41 12

Fig. 42

Fig. 43

N.B.: On certain helmets, the housing for the microphone rod must be created by cutting out the helmet border gasket along the pre-cut area.
FULL-FACE HELMETS · Take the polystyrene check pad (left side) and position the microphone in the special housing, as
illustrated in Fig. 44. Make sure that the side of the microphone with the caption “n” is facing the inside of the helmet (Fig. 45). · Secure the microphone to the cheek pad using the “microphone securing stickers”, see Fig. 44.

Fig. 44

Fig. 45

· Connect the microphone to the connector coming out of the e-Box (Fig. 46). · Position the left-hand side speaker in the cheek pad housing and secure it using the specific
adhesive (Fig. 47). · Reposition the left polystyrene cheek pad in its housing.
ONLY FOR FULL-FACE HELMETS: Insert the chin strap into the polystyrene cheek pad loop.

Fig. 46

Fig. 47

4.4. Repositioning the padding
· Pass the USB mini wire through the elastic band found on the comfort padding. · Replace the internal comfort padding by following the specific instructions found in the helmet user
manual.
Warning: Always verify the proper length of your chinstrap and adjust it if necessary, referring to the specific helmet instructions.
Warning: After the B902 is installed on the helmet, make sure the microphone is properly positioned in front of your mouth, if necessary adjusting the moveable element.
Warning: The wind protector, supplied as standard equipment with helmets that can be opened, may make it more difficult to open and close the chin guard when the microphone is installed.

13

EN
5. REMOVING THE SYSTEM To remove the system from the helmet, proceed as for the installation, by removing the various parts. Important: to remove the keypad, proceed as follows.
· Remove the keypad from the helmet shell (Fig. 48). · Remove the Flex of the keypad from the connector found on the e-box (Fig. 49). · Now completely remove the keypad from the helmet.

Fig. 48

Fig. 49

The keypad can be removed in case you decide to no longer use the system. However, it cannot be reused again as it will have lost its adhesive properties. Contact your local dealer to purchase a new keypad double sided- adhesive tape that will stick properly to the helmet shell.

6. BASIC FUNCTIONS
N.B.: Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely.

System ON System OFF

Press “ON” and keep it pressed for about 2 seconds, until the LEDs turn on and you hear the voice announcement. Press “ON” and keep it pressed for about 6 seconds, until the LEDs turn off and you hear the voice announcement.

6.1. Volume adjustment You can easily adjust the volume by tapping the “” or the “” key. You will hear a beep when the volume reaches the maximum or minimum level. Some volume parameters can be adjusted through the N-Com EASYSET APP for smartphone or the N-Com EASYSET computer program (chapter 6.4).
N.B.: The volume level set during the trip is not stored when the system is turned off. Each time the N-Com system is switched on, the audio goes back to the set default volume level.

6.2. Auto On / Off function If the helmet does not move for more than 60 seconds, the B902 system goes into “deep sleep” mode. The system is completely turned on as soon as movement is detected. If the system is in “deep sleep” mode for more than 3 days, it turns off completely. To turn it back on, the “ON” key needs to be pressed.
14

The “Auto On / Off” function is enabled by default on the device. You can enable / disable the function from the Configuration Menu (Chapter 8).
6.3. Multi-language voice messages The N-Com system features voice messages that provide information on the system and on the active functions.
The language set by default is English. The language of the voice messages may be changed through the specific firmware installable with the N-Com EASYSET program. Please refer to the online HELP for instructions on how to change the language settings.
Available languages: Italian, English, French, German, Spanish, Dutch.
The default function is enabled on the device. You can enable / disable the “VOICE ANNOUNCEMENTS” function by using the N-Com EASYSET program or the N-Com EASYSET APP.
6.4. N-Com EASYSET “N-Com EASYSET” is the application that can be used to manage and configure the B902 system. The program can be downloaded from the Internet site www.n-com.it, in the “Support/Download” section. The functions that can also be managed from the N-Com EASYSET are listed here below with the specific icon.
The N-Com system can be managed from the dedicated “N-Com EASYSET” APP, which makes it possible to configure the N-Com system directly from your Smartphone. The N-Com APP can be downloaded free of charge from Google Play or Apple Store. For additional details, please visit the website www.n-com.it The functions that can also be managed from the N-Com EASYSET APP are listed here below with the specific icon.
6.5. Updating the firmware The firmware updates of the N-Com system can be carried out through the N-Com EASYSET computer program.
· Download the N-Com EASYSET program from the N-Com website ­ in the “Support”/”Download”/”Software” section.
· Hook up the N-Com system to the computer and open the N-Com EASYSET program. · Follow the directions until the program recognises the N-Com system. · From the screen “FIRMWARE UPDATE”, select the desired language from the drop-down menu. · Click on “DOWNLOAD” and save the file in the computer. · Click on “UPDATE” and wait for the firmware update to end.
The release notes of the last Firmware version can be found on the website www.n-com.it ­ in the “Support”/”Download”/”Software” section.
15

EN
7. PAIRING UP MENU
All the Bluetooth pairing up operations are carried out in this mode. In order to access the Pairing up Menu starting with the N-Com system switched off, press the “ON” key and keep it pressed for 4 seconds. Once in the “Pairing up” menu, press the keys”” and “” to scroll through the various menu items. In the items marked with an “”, it is possible to enable / disable the function by pressing the “ON” key to confirm.
The following items make up the “Pairing up” menu: A. Mobile phone pairing (chapter 9) B. Intercom pairing (chapter 17.1) C. Pairing up Other N-Com Systems (chapter 17.2) D. Universal Intercom pairing (chapter 18.1) E. Second mobile phone pairing (chapter 10) F. GPS pairing up (chapter 14) G. Remote control pairing (chapter 19) H. Delete all pairings

In order to delete all Bluetooth pair ups stored in the device, press the key “” or “” until you hear the voice announcement “Delete all pairings”. Press the “ON” confirmation key to delete all Bluetooth devices stored in memory. I. Exiting the configuration To exit the “Pairing up” menu, press the key “” or “” until you hear the voice announcement “Exit the configuration”. Press the “ON” confirmation key to exit the “Pairing up” menu.
If no key is pressed within 15 seconds, the device automatically exits the “Pairing up” menu.
8. CONFIGURATION MENU
All the settings of the N-Com system are carried out in this mode. To access the Configuration Menu starting with the N-Com switched on, press the keys “” and “” for 4 seconds. Once in the “Configuration” menu, press the keys”” and “” to scroll through the various menu items. In the items marked with an “
”, it is possible to enable / disable the function by pressing the “ON” key to confirm.
The following items make up the “Configuration” menu: A. Speed dial (chapter 11.1) B. Smart Navi System (chapter 11.3) C. Auto On / Off (chapter 6.2) D. Audio Multitasking (cap. 16) E. Audio boost
By enabling the “Audio boost” (Audio Boost), all the audio sources inside the device will be reproduced at a higher and potentially less clear volume. Press the “ON” confirmation key to enable / disable the function, which is not enabled by default on the device. F. Reset* In order to restore the factory settings of the device, press the key “” or “” until you hear the voice message “Factory Reset”.
16

Press the “ON” confirmation key to restore all the factory settings of the device. G. Exiting the configuration*
To exit the “Configuration” menu, press the key “” or “” until you hear the voice announcement “Exit the configuration”. Press the “ON” confirmation key to exit the “Configuration” menu.
If no key is pressed within 15 seconds, the device automatically exits the “Configuration” menu.

9. MOBILE PHONE / MP3 PLAYER PAIR UP
· Make sure the B902 is turned off. · Put the system in the “Pairing up” menu: press the “ON” key and keep it pressed for 4 seconds,
until you hear the voice announcement “Pairing up Menu”. · Press the key “” to access the “Mobile phone pair up” mode. · Activate the search of Bluetooth devices on the mobile phone. · Select the N-Com device. If a password is requested, enter 0000 (four zeros). · Connection between the two devices is established after a few seconds.

N.B.: The affiliation is stored in the helmet and in the cell phone and it is not lost when the two devices are turned off. As a result it needs to be carried out only once.

Automatic Connection Manual Connection

Once the Bluetooth device has been paired up, connection is automatic when the system is turned on. In case connection is not automatically initiated after a few seconds, you can connect from the Bluetooth device or by pressing “ON” and keep it pressed for about 2 seconds.

10. SECOND MOBILE PHONE PAIR UP The B902 system can be hooked up to two phones at the same time. The second phone (secondary device) can receive calls but not make them.
To pair up the second Bluetooth phone (secondary device): · Make sure the B902 is turned off. · Put the system in the “Pairing up” menu: press the “ON” key and keep it pressed for 4 seconds,
until you hear the voice announcement “Pairing up Menu”. · Press the “” key until you reach the option “Second mobile phone pairing”. · Activate the search of Bluetooth devices on the mobile phone. · Select the N-Com system from the list. If a password is requested, enter the code 0000 (four
zeros). · After a few seconds, the connection between the two devices is activated.
N.B.: The affiliation is stored in the helmet and in the cell phone and it is not lost when the two devices are turned off. As a result it needs to be carried out only once.
Once the Bluetooth device has been paired up, connection is automatic when the system is turned on.

17

EN

11. MOBILE PHONE To pair up a mobile phone to the B902 system, follow the procedure illustrated in Chapter 9.

Answering a phone call
Vocal answer (VOX phone)
Voice call Hanging up/rejecting a phone call Manual phone connection

Briefly press any key when you hear the incoming call signal. When you hear the ringtone, say any word out loud. You can enable / disable the “VOX phone” function by using the N-Com EASYSET program or the N-Com EASYSET APP. The function is not active during the intercom connection. Press “ON” and keep it pressed for about 2 seconds.
Press “ON” and keep it pressed for about 2 seconds.
Press “ON” and keep it pressed for about 2 seconds.

11.1.

Speed dial

Using the N-Com EASYSET program or the N-Com EASYSET App, you can store up to 3 of your favourite numbers, which you will be able to dial from the “Speed Dial” menu.

Saving the Speed Dial numbers To assign one or more speed dialling numbers: · To access the Configuration Menu starting with the N-Com switched on, press the keys “” and
“” for 4 seconds. · Press the key “” or “” until you hear the voice command “Speed dial”. · Press the “ON” confirmation key. You will hear the voice announcements “Speed dial 1” and
“Phone connected”. · Press the keys “” or “” to select the speed dialling number to be assigned. The saved position
is confirmed by the voice announcement “Speed dial 1” / “Speed dial 2” / “Speed dial 3”. · On your own mobile phone (paired up and connected to the N-Com system), call the phone
number you wish to assign to the selected speed dialling position. The call is interrupted before it goes through, and the selected number will be saved; at this point you will hear the special voice announcement confirming the selection (“Save Speed Dial 1” / “Save Speed Dial 2” / “Save Speed Dial 3”).

Using the stored numbers To access the “Speed Dial” menu, press at the same time the “ON” and “n” keys (“Speed Dial”), then use the keys “” and “” to scroll through the menu items. Then press the “ON” key to confirm the selection of one of the following items:
· Last number redial · Speed Dial 1 · Speed Dial 2 · Speed Dial 3 · Cancelled

If you wish to exit the “Speed Dial” menu, press the keys “” and “” until you hear the command “Cancelled”, then press “ON” to confirm.

N.B.: If no key is pressed within 15 seconds, the system exits the “Speed Dial” menu.
18

11.2. Conference call function
When a call comes in on a mobile phone connected via Bluetooth to B902, the intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call.

Turning on the phone conference call function
Turning off the phone conference call function

During the phone call, briefly press “n” (channel 1). During the phone call, press the “n” key twice (channel 2). During the phone call, press the “n” key three times (channel 3).
During the phone call, briefly press “n”.

N.B.: “Telephone Conference” function can only be used with the N-Com series “600”/”900″.

11.3. Smart Navi System The “SMART NAVI SYSTEM” function allows you to listen to navigator directions coming from the smartphone even during an intercom call or while listening to the FM Radio. The audio stops to allow transmission of the navigator directions from the smartphone and is automatically re- established at the end of said instructions.
The “SMART NAVI SYSTEM” function is disabled by default on the device. You can enable / disable the function from the Configuration Menu (Chapter 8).
N.B.: With the Smart Navi System enabled, all audio information coming from the smartphone (for example, notification sounds) temporarily stops the audio under way.

You can enable / disable the “SMART NAVI SYSTEM” function by using the NCom EASYSET program or the N-Com EASYSET APP.

12. MUSIC VIA BLUETOOTH To pair up an Mp3 device to the B902 system, follow the procedure illustrated in Chapter 9.

Play music (Play) Pause function (Pause) Next track (Skip) Previous track (Rew)

Briefly press “ON”. When the player is connected and playing music, briefly press “ON”. When the player is playing music, press “” for about 2 seconds.
When the player is playing music, press “” for about 2 seconds.

19

EN
12.1. Sharing music via Bluetooth (A2DP Sharing) During the intercom connection, you can start playing music by briefly pressing the “ON” key. The music will be played in both systems. Music sharing temporarily cuts off the intercom conversation; however, this can be automatically restored by stopping the music (this is done by briefly pressing the “ON” key).
N.B.: Music shared through the intercom can be managed by both systems, for example, both systems can change the track by pressing the relative command.
N.B.: When the “Audio Multitasking” function (chapter 16) is enabled, the “Music Sharing” function is temporarily disabled.
N.B.: the “Music Sharing” function can only be used with the N-Com series “600”/”900″.

13. MUSIC VIA CABLE
Connect the mini USB connector of the Multimedia Wire (not included) to the helmet and the other end to the audio device. A coloured band on the cable indicates the connector to be hooked up to the audio device.

Turning on the cable audio Turning off the cable audio

Press the “ON” key three times. Press the “ON” key three times.

N.B.: While listening to music via cable, it will not be possible to keep the intercom connection active.

14. NAVIGATOR PAIR UP B902 system is compatible with the most common satellite navigators for motorcycles. For a list of compatible models and additional details, visit the website www.n-com.it
· Make sure the B902 is turned off. · Put the system in the “Pairing up” menu: press the “ON” key and keep it pressed for 4 seconds,
until you hear the voice announcement “Pairing up Menu”. · Press the “”key until you reach the option “GPS Pair up”. · Activate the search of Bluetooth devices on the navigator. · Select the N-Com system from the list. If a password is requested, enter the code 0000 (four
zeros). · After a few seconds, the connection between the two devices is activated.
N.B.: The pair up is stored by both the helmet and the navigator hence it is not lost when they are switched off. This means that this procedure needs to be carried out only once. Once the Bluetooth device has been paired up, connection is automatic when the system is turned on.
N.B.: Intercom connection is automatically cut off every time the navigator gives directions and restored at the end of the message from the navigator. Should you wish to keep the navigator audio active even during the intercom connection, please refer to chapter 16 “Audio Multitasking”.

20

15. FM RADIO Turning on the radio Turning off the radio New station automatic search
Pre-setting a radio station (max. 6 stations)
Changing radio stations (among the pre-set ones)

Press the “ON” key twice.
Press the “ON” key twice.
Press “” and keep it pressed for 2 seconds. Press the key “” and keep it pressed for about 4 seconds, until you hear the word “Pre-set”. Select the pre-setting position using the keys “” and “”. Saving is confirmed by means of a voice message.
Press “” and keep it pressed for 2 seconds.

This function can also be turned on using the “N-Com EASYSET” program or through the “N-Com EASYSET APP” for Smartphone Android, iPhone, iPad.

16. AUDIO MULTITASKING
The Audio Multitasking function makes it possible to listen to audio coming from different sources at the same time. When the Audio Multitasking function is enabled, phone calls, GPS directions and intercom conversations can overlap the audio of the FM radio, of the music or of the directions coming from the GPS app of a smartphone in the background at a lower volume.

The following audio overlaps are possible:

AUDIO IN THE FOREGROUND A. INTERCOM B. INTERCOM C. INTERCOM D. PHONE CALL E. GPS F. GPS

AUDIO IN THE BACKGROUND FM RADIO GPS MULTIMEDIA AUDIO FROM THE SMARTPHONE GPS FM RADIO MUSIC FROM THE SMARTPHONE

Notes: · The Audio Multitasking function is compatible with Android devices. On iOS devices, on the other
hand, the use of the Audio Multitasking function is limited. · The Audio Multitasking function can only be used between N-Com B902 systems.

16.1. Enabling / disabling the Audio Multitasking function By default, the Audio Multitasking function is disabled on the device.
It can be enabled / disabled through the Configuration Menu (chapter 8), the N-Com EASYSET program or the N-Com EASYSET APP. Once the function has been enabled / disabled, the N-Com system needs to be switched off and then switched on in order to store the selection.

21

EN
N.B.: When the Audio Multitasking function is enabled, the “Music Sharing” function (chapter 12.1) is temporarily disabled.
N.B.: When the Audio Multitasking function is enabled, the “Intercom HD” function is temporarily disabled.
16.2. Adjusting the volumes Increasing or decreasing the volume of the foreground audio also increases or decreases the volume of the background audio. The volume of the foreground audio can be adjusted through the N-Com system (chapter 6.1). The volume of the background audio can be adjusted through the N-Com EASYSET APP (with the Audio Multitasking function enabled). The background volume is pre-set at level 5.
The “Audio Multitasking” function can be enabled / disabled by means of the NCom EASYSET program or the N-Com EASYSET APP.

17. INTERCOM The N-Com B902 system allows communication with other N-Com systems, up to a maximum distance of about 300 m1 (in open field, with no obstacles). The range of the communication varies depending on the N-Com systems used.
N.B.: The range and quality of the communication may vary significantly depending on the presence of obstacles, weather conditions, and magnetic fields.

17.1. N-Com “600”/”900″ Series Intercom pairing up
Important: The procedure described below refers exclusively to the pairing up between the “600”/”900″ series N-Com systems.
· Make sure the systems are turned off. · Put the systems in “Pairing up” menu: press the “ON” key and keep it pressed for 4 seconds, until
you hear the voice announcement “Pairing up Menu”. · On both systems, press the key “” until you reach the option “Intercom pairing”. · On system A, press the key pertaining to the “pre-setting position” where you wish to save
system B.

Pairing up CHANNEL 1 Pairing up CHANNEL 2 Pairing up CHANNEL 3

Briefly press “n”. Press the “n” key twice. Press the “n” key three times.

· No key must be pressed on system B.

1 The carbon fiber used to make the X-lite helmets interfere with the transmission of the Bluetooth radio system. Therefore, the quantity and/or position of the carbon in the helmet causes a reduction in the communication distance that varies depending on the helmet model being used. The reduced distance concerns all the intercom systems available on the market, whether built-in or not.
22

The Intercom connection with the selected channel is automatically activated at the end of the pair up procedure.
Through the N-Com EASYSET APP, the “Intercom Easy Pairing” can be carried out. This mode allows the N-Com systems to be recognised and stored through a QR code generated on one’s smartphone. The Intercom Easy Pairing function is only available for B902 systems.

17.2. Pairing up other N-Com
Important: The procedure described here below refers exclusively to the pairing up of “900” series NCom systems with N-Com systems OTHER THAN the “600”/”900″ series 2.
· Make sure the systems are turned off. · Put B902 system in “Pairing up” menu: press the “ON” key and keep it pressed for 4 seconds, until
you hear the voice announcement “Pairing up Menu”. · Put the N-Com system in “Setting” mode: press the “ON” key and keep it pressed for 4 seconds,
until the blue LED starts to flash quickly. · On B902 system, press the key “” until you reach the option “Pairing up other N-Com”. · On B902 system, press the key pertaining to the “pre-setting position” where you wish to save the
other N-Com system.

Pairing up CHANNEL 1 Pairing up CHANNEL 2 Pairing up CHANNEL 3

Briefly press “n”. Press the “n” key twice. Press the “n” key three times.

The Intercom connection with the selected channel is automatically activated at the end of the pair up procedure.

17.3. Intercom function (one-to-one connection)
To establish an Intercom connection with one of the systems stored in memory, simply press the command related to the channel where the system was saved.

Connection CHANNEL 1 Call CHANNEL 2 Call CHANNEL 3 Disconnection of active intercom

Briefly press “n”. Press the “n” key twice. Press the “n” key three times. Briefly press “n”.

N.B.: In case the pre-setting position is empty, or the system being called cannot be reached within the maximum range or it is already engaged in a phone call, you will hear an error voice message.
N.B.: In case the Intercom connection system falls outside the range (Intercom connection interrupted), the B902 system will automatically try to reconnect every 8 seconds. Double beeps will be emitted until the Intercom connection is not restored.

2 Except for Bluetooth kit and Bluetooth kit2, which are not compatible.
23

EN
If you do not want automatic reconnection, press the “ON” key to stop the automatic reconnection attempts. The B902 system is equipped with the “VOX Intercom” function, which makes it possible to switch the intercom on and off vocally. In order to work properly, the VOX Intercom function must be enabled on both systems connected via intercom. The VOX Intercom function is disabled by default on the device.
You can enable / disable the “VOX Intercom” function and set the activation sensitivity, using the N-Com EASYSET program or the N-Com EASYSET APP.
If the function is enabled, the system works as follows: · The intercom switches on automatically by saying any word out loud into the microphone of one
of the two helmets. · The intercom switches off automatically when both users do not speak for 20 seconds. If the
intercom conversation was started by pressing the manual connection key, the intercom must be manually disconnected as well. In the event that the VOX Intercom function is enabled on the device, but the last connected channel is not available or cannot be reached, it is advisable to temporarily disable the VOX Intercom function by pressing the “” key for 5 seconds. By doing so, the system will not attempt to connect to the last connected channel every time a word is spoken out loud. The temporary disabling of the VOX function is then removed the first time the N-Com device is turned off; so, if the VOX Intercom is enabled (from PC or APP), it will be restored the next time the device is switched on. N.B.: The VOX Intercom function can be used EXCLUSIVELY with “900” series N-Com systems.
17.4. Smart Conference (Group Intercom) Thanks to the “Smart Conference” function, you can start the conference communication between NCom intercom systems of the “900” series previously paired up and saved in the 3 available channels. All systems must be turned on and available within the connection range.
1. Each system must have been previously paired up to all the other systems: B, C and D.
24

2. Any system can press the “n” key for 2 seconds to activate the Group Conference or to start a conference communication between all the systems.

3. In the case where one of the systems presses the “n” key or falls outside the connection range, the group intercom is interrupted.

Smart Conference connection Smart Conference disconnection

Press the “n” key for 2 seconds. Activation is confirmed by a beep in the helmet and by the voice message “Group Intercom”. Briefly press the “n” key. Disconnection is confirmed by the voice announcement “Group Intercom terminated”.

N.B.: During a “Smart Conference” call, connection to the mobile phones of all participants is temporarily cut off. When the conference call ends, all phones automatically reconnect to their own intercom system.
N.B.: The “Smart Conference” mode can be used EXCLUSIVELY with “900” series N-Com systems”. N.B.: The “Smart Conference” mode CANNOT be used with systems paired up in Universal Intercom
mode (chapter 18).

18. “UNIVERSAL INTERCOM” INTERCOM The N-Com B902 system can be connected via Bluetooth to intercom systems of other brands, thanks to the UNIVERSAL INTERCOM function 3.
18.1. Pairing up the UNIVERSAL INTERCOM
The N-Com system can be paired up to the other intercom (from now on referred to as Intercom B) as if it was a mobile phone.
· Make sure the B902 is turned off. · Put the B902 system in the “Pairing up” menu: press the “ON” key and keep it pressed for 4
seconds, until you hear the voice announcement “Pairing up Menu”. · Press the “” key until you reach the option “Universal intercom pairing”. · Put intercom B in the mobile phone pairing up mode. Important: If the intercom allows
management of two mobile phones, put it in pair up mode of the second mobile phone. By doing so, it will be possible to maintain the connection to your own mobile phone even during intercom communication (refer to the Intercom B manual). · On the B902 system, press the control related to the “memory position” where you wish to store intercom B.

3 Except for Bluetooth kit and Bluetooth kit2, which are not compatible.
25

EN

Pairing up of CHANNEL 1 Pairing up of CHANNEL 2 Pairing up of CHANNEL 3

Briefly press key “n”. Press 2 times key “n”. Press 3 times key “n”.

N.B.: In case there are already other intercom systems stored in the memory of the B902 system, check on the EASYSET N-Com App which channels are still available. If a channel that is already used is selected during pair up, the new intercom system will overwrite the one previously stored on that channel.
· After a few seconds, Intercom B will emit the confirmation beep.

18.2. Universal Intercom Function To turn on and off the audio between two helmets, proceed as follows:
From the N-Com B902 system: Connect or disconnect Intercom B as you would for a regular N-Com intercom (chapter 17.3). Intercom B may receive a dialling tone that must be answered with a phone reply command.
From intercom B To enable the intercom connection, press the “Voice Call” or “Last number redial” command. To disable the intercom connection, press the “Hang up” or “Reject phone call” command. N.B.: Some systems are not able to handle the activation / deactivation of the intercom connection. In
this case, operate from the B902 system.
N.B.: · During use of the UNIVERSAL INTERCOM, the B902 system keeps the connection active to the
MAIN DEVICE only (and not to the SECOND MOBILE PHONE or to the SATELLITE NAVIGATOR). · The intercom system connected to N-Com B902 may not allow simultaneous connection to a
mobile phone. · Only one system paired up in Universal Intercom mode can be stored.

18.3. Universal Conference (chain intercom) The “Universal Conference” mode can be used to connect in conference call N-Com systems of the “900” series and one system paired up in Universal Intercom mode.
The connection procedure is outlined in the diagram provided here below: 1. System A must have been paired up beforehand to two B systems (Universal Intercom pair up) and C.

2. System A has to initiate the first intercom connection with system B (Universal Intercom), by pressing the relative intercom connection command.
26

3. At this point, system C can join the intercom conference call, establishing an intercom connection with system A.

4. The three systems are now in intercom conference call mode and can talk to each other at the same time.
5. In case you wish to add another system (D), the latter must be paired up beforehand to system C. Press the relative connection command to start a 4-participant intercom conference call.
N.B.: The “Universal Conference” mode can also be used by connecting only “900” series N-Com systems”.
N.B.: The “Universal Conference” mode can also be used by connecting “900” series N-Com systems with other N- Com devices (B601, B5, B1.4, etc.).

19. REMOTE CONTROL
The B902 device can be controlled by using a remote control (sold separately), so that you do not have to take your hands off the handlebars to use the keypad. The N-Com system is compatible with the RC4 Remote Control by SENA. The following table shows the correspondence of the keys:

N-COM SYSTEM

ON

N

SENA RC4

+ – CENTRAL KEY MULTI-FUNCTION KEY

Proceed as follows to pair up the N-Com system to the RC4 Remote Control: · Make sure the RC4 is switched off. · Put the RC4 in pair up mode: press the “+”key and keep it pressed for about 8 seconds. · Make sure the B902 is switched off. · Put the B902 system in the “Pairing up” menu: press the “ON” key and keep it pressed for 4
seconds, until you hear the voice announcement “Pairing up Menu”. · Press “” key to access the “Remote control pair up” mode. · Press the “ON” key on the N-Com system keypad. · After a few seconds, the connection between the two devices is confirmed by the voice
announcement “Remote control connected”.

N.B.: The affiliation is saved by both the helmet and the remote control and it is not lost when the two systems are turned off. Hence this procedure must only be carried out once.

27

EN
20. BATTERY AND RECHARGE 20.1. Low battery signal During its operation, the system alerts the user with a voice message when the battery is low. From the first message, the system has a 1-hour autonomy. Warning is given every 10 minutes.
20.2. Checking the Battery Level LED Indicator When the system is powering on, their blue LED flashes rapidly indicating the battery level. 4 flashes = High, 70 ~ 100% 3 flashes = Medium, 30 ~ 70% 2 flashes = Low, 0 ~ 30%
Vocal Indicator Starting with the system turned off, press at the same time the “ON” and “” keys for about 4 seconds until you hear three, high toned beeps. Then you will hear a voice prompt indicating the battery level. However, if you release the keys as soon as the system turns on, you will not hear a voice prompt for the battery level indication.
20.3. Charging the system

To charge the system, hook it up to the battery charger supplied as standard equipment or to a USB outlet powered with the USBmini USB cable supplied as standard equipment.

Fig. 50

The charge will take place as follows:

B902 system turned off B902 system turned on

When the B902 system is connected to the battery charger, the blue LED starts to flash quickly. When the battery is charged, the blue LED becomes steady. When the B902 system is connected to the battery charger, the blue LED starts to flash quickly. When the battery is charged, the blue LED goes back to its standard flashing.

N.B.: In case you are not planning on using the N-Com system for a long time, you need to fully recharge the device before storing it away.
N.B.: In case the device is not used for a long time, carry out a complete recharging cycle of the device at least once every 6 months to avoid possible damage to the battery.
N.B.: In case the N-Com system is left for more than 6 months without ever being recharged, the device may not switch on; in this case, recharge the N-Com system for at least 24 hours (even if the blue signalling LED is not flashing), then try to switch on the device again.

28

21. SUMMARY TABLE OF CONTROLS

Basic Functions

Bluetooth Devices

key
Turning on Turning off Increase Volume Decrease Volume Pairing up Menu Configuration Menu
Answer phone call
Voice call Speed Dialling Menu
Hang up/reject a phone call Manual Device Connection Phone Conference Activation CHANNEL 1 Phone Conference Activation CHANNEL 2 Phone Conference Activation CHANNEL 3 Turning off the Conference function
Play music (Play) Pause Function (Pause) Next track (Forward) Previous track (REW) Share A2DP music Activate audio via cable Deactivate audio via cable
Connection CHANNEL 1 Disconnection of active intercom Calling CHANNEL 2 Calling CHANNEL 3 Group intercom connection Group intercom disconnection
Turning on the Radio Turning off the Radio Automatic search for new station Change station (pre-set stations) Pre-set station

n
X X
X x2 x3 X
X X x2 x3 2 sec X

Cable

N-Com Intercom Bluetooth Music /

(600/900 series)

Radio Menu

Press any key on the N-Com keypad. Press the keys at the same time. Starting with the system switched off.

ON 2 sec 6 sec
4 sec X
2 sec X
2 sec 2 sec
X X
X x3 x3
x2 x2

X X
2 sec
2 sec

X X
2 sec
2 sec 4 sec

  • 4 sec

29

EN
22. WARRANTY With this WARRANTY CERTIFICATE, Nolangroup warrants to the purchaser that the product, at the time of purchase, is free from defects in materials and workmanship. We kindly ask you to: · Read the warnings for safety and proper use. · Read the warranty terms and conditions. · Keep the original purchase receipt. This receipt must be presented in case of repairs under
warranty. In these cases, the product must be sent to the dealer where the purchase was made.
22.1. Warranty coverage and validity If any defect covered by this warranty certificate is detected within the period specified for the country of purchase (see table at the bottom of this leaflet) from the date of purchase shown on the receipt, Nolangroup will repair or replace the defective product through its distribution network and after having verified the defect. Nolangroup will provide all material and labour reasonably necessary to remedy the claimed defect, except in the cases where damage is caused by one of the items listed in the following paragraph “Exclusions and limitations of coverage”.
22.2. Exclusions and limitations of coverage This warranty covers only defects in materials and workmanship. Nolangroup cannot be held liable for product defects attributable in whole or in part to any other cause, including but not limited to:
· Defects or damage resulting from use of the Product in conditions other than the usual ones. · Damage caused by improper use and not in compliance with normal operation as indicated in the
instructions for use and maintenance of the product provided by Nolangroup. · Neglect and normal wear and tear of internal and external parts. · Any damage resulting from an accident. · Any modification or tampering made to the helmet or to the N-Com system by the user or third
parties. · Use of incompatible accessories not approved by Nolangroup for the purchased N-Com device
model. · Consumable parts considered to be subject to wear and tear, such as the rechargeable battery and
the connection cables between N-Com systems and other devices. · The proper functioning of the product/peripheral device combination when the product is used
together with accessories or equipment for which Nolangroup has not verified compatibility. · All specific and subjective situations that may arise during actual use of the helmet, such as, for
example, problems related to comfort while riding or aerodynamic noise.
Under no circumstances shall Nolangroup be liable for any incidental or consequential damages (including, without any limitation whatsoever, injuries to one or more persons) resulting from failure to fulfil the obligations arising from this warranty regarding Nolangroup products.
22.3. Procedure for submitting claims In order to submit any claim covered by this warranty, the purchaser must notify directly the dealer where the N-Com system was purchased of the alleged defect, presenting at the same time the product which is the object of the claim and a copy of the sales receipt.
30

PRIOR TO CONTACTING THE DEALER, WE RECOMMEND THAT YOU CAREFULLY READ THE INSTRUCTIONS FOR USE ENCLOSED WITH THE PRODUCT. THE WARRANTY IS EFFECTIVE EXCLUSIVELY FROM THE DATE OF PURCHASE UNTIL THE PERIOD INDICATED FOR THE COUNTRY WHERE THE PRODUCT WAS PURCHASED (please see table provided at the end if this leaflet). Any repairs or other jobs carried out under warranty do not extend the period of the warranty itself. Hence, in case the product or one of its components is replaced, this does not mean the start of a new warranty period, as the purchase date of the original product will be taken into account for warranty purposes. Only for repairs or replacements of electronic components, if Nolangroup repairs or replaces the product, the product will have a warranty period equal to the remaining part of the original warranty or ninety (90) days from the date of repair (whichever is longer). Repair or replacement may also be carried out using regenerated components with equivalent functions. Replaced parts or components will become the property of Nolangroup. NOLANGROUP RESERVES THE RIGHT TO CHANGE CHARACTERISTICS, FUNCTIONALITY, COMPATIBILITY AND SOFTWARE AT ANY TIME, WITH NO NEED FOR ADVANCE NOTICE. This warranty does not affect the customer’s legal rights under applicable national jurisdiction and the consumer’s rights vis-à-vis the dealer under the purchase/sale agreement. 22.4. Product identification N-Com products are identified by means of a code that allows their traceability and identification. The identification code can be found on the adhesive label affixed to the B902 system.
31

EN

22.5. Validity of N-Com warranty

NATION
ALBANIA ALGERIA SAUDI ARABIA ARGENTINA AUSTRALIA AUSTRIA BAHRAIN BELGIUM BRP BERMUDA BOLIVIA BOSNIA-HERZEGOVINA BRAZIL BULGARIA BURKINA FASO CANADA CANADA BRP CHILE CHINA CYPRUS COLOMBIA SOUTH KOREA COSTA RICA DENMARK ECUADOR EL SALVADOR UNITED ARAB EMIRATES PHILIPPINES FINLAND FRANCE GERMANY GHANA JAPAN JORDAN GREAT BRITAIN GREECE GUADALUPE GUATEMALA FRENCH GUYANA HONG KONG INDONESIA IRAN ICELAND ISRAEL KAZAKHSTAN KUWAIT

VALIDITY 2 YEARS
X X
X
X
X
X X X
X X

VALIDITY 1 YEAR
X X X X X
X
X X X X
X X X X X
X X X
X X X X
X X X
X X X X X X X X X X

NATION
LEBANON MACEDONIA MALAYSIA MALTA MOROCCO MAURITIUS MEXICO MONTENEGRO NORWAY NEW CALEDONIA NEW ZEALAND OMAN NETHERLANDS PAKISTAN PARAGUAY PERU FRENCH POLYNESIA POLAND PORTUGAL QATAR CZECH REPUBLIC SLOVAK REPUBLIC REUNION ROMANIA RUSSIA SAINT-MARTIN SERBIA SINGAPORE SLOVENIA SPAIN UNITED STATES SOUTH AFRICA SWEDEN SWITZERLAND THAILAND TAIWAN TANZANIA TRINIDAD & TOBAGO TUNISIA TURKEY UKRAINE HUNGARY VENEZUELA ZAMBIA

VALIDITY 2 YEARS
X
X
X X X X X
X X X
X

VALIDITY 1 YEAR
X X X
X X X X X X X X
X X X X
X
X
X X X X
X X
X X X X X X X X
X X

32

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals