Eventide TriceraChorus B-Stock Pedal User Guide

June 6, 2024
Eventide

TriceraChorus B-Stock Pedal

TriceraChorus Quick Reference Guide

Mix
Left: 0-99 Mix of Chorus voices Center: 100 Vibrato mode (no dry) Right: 99-0 Mix of Chorale voices

Rate
Chorus modulation rate 0.1-20 Hz controlled by external Tap switch or sync’d to MIDI Clock when enabled

Left
Modulation Depth of the Left channel voice

Detune
Mix for the stereo Detune section, independent of the Chorus/Chorale Mix
Button/LED
Toggles Primary/Secondary Parameter Control LED ON = Secondary LED OFF = Primary

Preset LED Ladder

Right
Modulation Depth of the Right channel voice

ACTIVE Button/LED
LED lit when ACTIVE Press to toggle action of
ACTIVE Footswitch LATCHING< >MOMENTARY
ACTIVE/BYPASS
Preset Mode: Load Preset

SWIRL/Preset
Press & Hold to toggle between Preset Select and SWIRL Modes

Center
Modulation Depth of the Center channel voice
SWIRL Button/LED
LED OFF = Preset Select Mode LED RED = SWIRL Mode
LED GREEN = SWIRL is ON Press & Hold to Save Preset

Knob Functions ­ Secondary Parameters

Rate Env
Controls amplitude envelope amount sent to the
rate of the LFOs
Mix Env
Controls amplitude envelope amount sent to both Chorus/Chorale
mix and Detune Mix
Delay
Chorus: up to 200ms delay for all voices
Chorale: Delay/Depth for each voice up to 200ms
IN
TS (mono) or TRS (stereo)
Mono/Stereo Switch
Left = Mono (TS plug) Right = Stereo (TRS plug) In Stereo, Tip is OUT1, Ring is OUT2

Press button to toggle Secondary/Primary parameters

Pitch
Stereo detune (in cents) Fully CCW: -40L/+40R Center: 0L/0R Fully CW: +40L/-40R
Filter
CCW: Low Cut Center: Flat CW: High Cut
Out Lvl
Center for unity gain Boost/Cut output level
EXP
Connect Expression Pedal, Auxiliary Switches or TRS MIDI
(See System Setup)
Power
9VDC center-negative

OUT1 & OUT2
In Mono, both outputs have the same dry signal

I/O Level Switch
Left = Guitar
Right = Line/Effects Loop

Mini USB
Software updates & MIDI over USB

Expression Pedal
Morphing from Heel to Toe
An Expression Pedal can be used to change any grouping of knob Parameters in one smooth gesture. Programming an Expression Pedal is easy. You simply need to set end points for Heel & Toe. Here’s how:
1. Press Pedal fully Heel down. 2. Adjust any combination of the Parameter
control knobs. 3. Press Pedal fully Toe down. 4. Adjust any combination of the Parameter
control knobs. 5. Save it or lose it. See “Saving a Preset.”
Clear Expression Pedal Mappings To clear the Expression Pedal mappings for the knobs, hold the ACTIVE Footswitch and, while holding, press the ACTIVE Button until the Preset Ladder LEDs flash twice.
NOTE: To use an Expression Pedal, the Exp Pdl Jack must be set to either [EXP] or [EXP + AUX]. See System Setup to select.

MIDI Messages

Save Preset
Enter Save Mode by pressing and holding the SWIRL Button, then a MIDI program change message will save a Preset to the Preset Slot of the given value 1-127.
Load Preset
MIDI program change message loads the Preset from the Preset Slot of the given value 1-127. Note: The bottom two Ladder LEDs will be lit when Presets 6­127 are selected via MIDI or Device Manager.

Receive/send using the USB Port or Exp Pdl Jack*. CC 4: Expression Pedal CC 9: Tap RATE CC 14: ACTIVE/BYPASS (>=64 is Active) CC 15: SWIRL (>=64 is SWIRL)

Parameters: CC Messages Map

CC PRIMARY CC SECONDARY

20

Mix

26 Mix Env

21 Rate 27 Rate Env

22 Detune 28 Pitch

23 Left 29 Delay

24 Center 30 Filter

*Use a MIDI Converter Box

25

Right

31 Out Lvl or a DIN to TRS or TRS cable

System Setup

Enter System Setup
To access these Global Settings, apply power while holding ACTIVE Footswitch and button. Top two LEDs light when in System Setup. Changes are stored as they are made. Cycle power to exit System Setup.

Set MIDI Channel
PRESS
1 2 3 4 5… 16 Set MIDI Channel: Click SWIRL Button
Default = Omni
Set MIDI Clock
PRESS
ON

Set Bypass Mode

PRESS

BUFFER RELAY DSP+FX

KILL-DRY
Toggles On or Off for each setting Factory Default = Buffered

Catch Up ON/OFF

PRESS
ON

MIDI Clock disables Aux Tap switch and CC9 Factory Default = Off

Factory Default = Off

Set Exp Pdl Jack

PRESS

EXP (Default) EXP + AUX TRIPLE AUX MIDI BOX MIDI TRS

[EXP+AUX] TIP = Expression Pedal RING = Tap RATE
[TRIPLE AUX] TIP = Increment Preset RING = Decrement Preset TIP + RING = Load Preset Note: Times out after a few seconds
[MIDI BOX] Receive and Send MIDI via a MIDI Converter Box (Tip Active)
[MIDI TRS] Receive MIDI directly with a DIN to TRS or TRS cable.

Presets – 5 On Board, 127 Via MIDI

The currently loaded Preset is indicated on the Preset LED Ladder. When a Preset is modified the Preset LED blinks once.

Load Presets
To select and load a Preset using Footswitches:

Save Presets
To save one of the 5 Presets using the Buttons:

1. SWIRL Footswitch selects Preset 1 to 5. Preset 1 (top LED) to Preset 5 (bottom LED) blinks.
2. ACTIVE Footswitch loads the Preset. LED stops blinking.
NOTE: To select Preset, SWIRL Footswitch must be in Preset mode. If SWIRL LED is lit, press and hold SWIRL Footswitch.
Catch Up Knob Function

1. Press & hold SWIRL Button – Blinking Ladder and Button LEDs let you know you have entered Save Mode.
2. SWIRL Button selects Preset 1 to Preset 5. 3. ACTIVE Button saves Preset
– LEDs stop blinking to let you know the Preset is saved.
NOTE: SWIRL status is saved with the preset. Save Mode times out after a few seconds. Pressing either Footswitch exits Save Mode.

When a Preset is loaded or when toggling between Parameters using , Knob positions will not align with their current Parameter values. As a result, turning a knob will likely cause an abrupt change in the sound.

With Catch Up ON, the sound does not change until the Knob is moved to the position corresponding to the current value. The LED Ladder indicates whether the knob must be turned CCW (top LED blinks) or CW (bottom LED blinks). The LED flashes more rapidly as the knob approaches the value set by the Preset. All five LEDs blink once when the knob matches the stored Parameter value.

NOTE: To enable/disable Catch Up Knob Function, power up in System Setup mode and press SWIRL Footswitch to toggle ON/OFF.

SWIRL Footswitch Functionality

Press & Hold the SWIRL Footswitch to toggle between SWIRL mode and Preset Select mode. In SWIRL mode, press the SWIRL Footswitch to turn ON/OFF SWIRL.

STATUS

FUNCTION

EFFECT

LED OFF Preset Mode

Press SWIRL Footswitch to increment presets

LED RED SWIRL OFF

Press SWIRL Footswitch to activate SWIRL

Swirl adds another dimension to TriceraChorus’ sound via stereo phase shifters after the Detune section to create throbbing and swooshing effects.

LED GREEN SWIRL ON

The amount of Swirl depends on the greater level of either Chorus Mix or Detune Mix and follows the Env Mix control. Swirl speed is adjusted by Rate and follows the ENV Rate control. Use faster rates to achieve deeper Swirl effects.

Device Manager Software

Available from Eventide’s website for Mac & PC

– Update Pedal Firmware – Backup/Restore entire device to a file – Restore Factory Settings – Edit System Settings

– Import/Export Presets

– View, edit, and organize Presets

Download: eventideaudio.com/edm

Instructional Videos eventideaudio.com/TriceraChorus-pedal
Technical Support eventideaudio.com/support

Restore Factory Settings: Boot pressing ACTIVE Footswitch & ACTIVE Button Follow us on Social Software Update: Boot pressing SWIRL Button & SWIRL Footswitch
TriceraChorus Quick Reference Guide for Firmware v1.0+| Eventide Part# 141348 Rev A Eventide is a registered trademark of Eventide Inc. © 2021 Eventide Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals