MARLEY EM-JT002 Stir It Up Wireless User Guide

QUICK START GUIDE
STIR IT UP WIRELESS
ATTENTION, PLEASE READ QUICK START GUIDE BEFORE USE

 PRODUCT MAP

LEGEND

1. Spindle
2. Turntable
3. 45 Adaptor
4. Balance Weight
5. Anti-Skating Knob
6. Tone Arm Lift Level| 7. Tone Arm Rest Holder
8. Tone Arm
9. Stylus
10. Needle Cover
11. Off/33/45 Knob
12. Power Adaptor With 4
Interchangeable Plugs
---|---

FUNCTION LAYOUT

LEGEND

A. RCA Line Out
B. Pre-Amp Switch Button
C. USB to PC Recording
D. Off/33/45 Knob| E. Bluetooth® Button
F. – VOL + Knob
G. Headphone Jack
H. Anti-skating Knob
---|---

 POWERING ON YOUR STIR IT UP WIRELESS

• Your Stir It Up Wireless uses an AC power supply and is powered by a standard wall outlet.
• Connect the power adaptor to the wall outlet.

BLUETOOTH® PAIRING

• Power on the external Bluetooth® device first before turning on the BT function on the Turntable.

• Press the BT button on the turntable to turn on the Bluetooth® transmitter.

• Press the button again to enable the unit to search the Bluetooth® device till the BT indicator light becomes solid.
  This will be indicated your devices are paired.

• Blue LED light flash

• Blue LED light stable

DISCONNECT BLUETOOTH® PAIRING

Long press and hold the BT button till the BT indicator light turns off. The turntable will then disconnect from an external device.

• The Blue LED light will turn off.

PLAYING A RECORD

1. Put a vinyl record on the turntable.
2. Assemble the balance weight and set it to a proper position.
3. To adjust the balance weight rotate the balance weight at counter-clockwise.
4. Lift and move the tonearm to the turntable. Place the tonearm on the edge of the record.
5. Turn the RPM Dial knob to select the speed according to the record you are playing.
6. The turntable platter will auto stop when the music has ended. Lift the tonearm and place it to tone arm rest manually.
   To listen to side B, flip the record, and repeat the above steps.

33 RPM speed to play corresponding size 33 vinyl disc
45 RPM speed to play corresponding size 45 vinyl disc
To power, the unit off Rotate the RPM Dial knob to the off position.
Note:
Remove the needle cover before you balance the tonearm.
Hold tonearm whenever you make any adjustment or action so as to protect the tonearm.
Do not try to adjust the balance weight while playing a record as this could break the needle and scratch the record.
Re-secured the tonearm before transportation to protect the needle.
Remove the balance weight before transportation to prevent damage or breakage to the unit.
Do not stop or turn the platter manually. Moving or jarring the turntable without securing the Tonearm clamp could result in damage to the Tonearm.

ANTI-SKATING

Normally the anti-skating should be set to its minimum setting. Anti-skate compensates for inward tracking forces that occur with certain pick-ups when the stylus nears the center of the record. If the turntable is experiencing excessive skipping while nearing the center spindle, try increase the anti- skating in the increments indicated on the dial. Start by adding an increment of 1, test its performance, then increase it more, and so on.
Note: During adjusting the anti-skating knob, leave the tone arm and balance weight alone to prevent damaging the stylus (needle).

VOLUME CONTROL

Increase Volume: Rotate the Volume Knob clockwise.
Decrease Volume: Rotate Volume Knob counterclockwise.

HEADPHONE OPERATION VIA HEADPHONE JACK

Connect a set of headphones (not included) in the headphone jack.

Note: Never put on the headphone till you have plugged in the headphone plug

USB TO PC RECORDING

Download Full instruction for the Audacity Software at: http://www.audacityteam.org/download/

• Connect the Turntable and the computer via the provided USB cable.
• Follow the instruction of the software installation steps and operation interface.

NON-BLUETOOTH® CONNECTION SETUP

CAUTION: Switch off the power to all equipment before making connections. Read the instructions of each component you intend to use with this unit. Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection cables together with the AC power cord.

√ COMPLIANCE INFO

STIR IT UP WIRELESS
READ ALL INSTRUCTIONS BEFORE USE AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC RF EXPOSURE STATEMENT:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISEDC STATEMENT
This device complies with Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)  this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The device complies with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.

ISEDC RF EXPOSURE STATEMENT:
The device is in compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.

BATTERY REPLACEMENT STATEMENT IN EUROPE
Your Stir It Up Wireless includes a rechargeable battery designed to last the lifetime of the product. In the unlikely event that you should require a replacement battery please contact Customer Services who will supply details of the warranty and out-of-warranty replacement battery service.
BATTERY DIRECTIVE
This symbol indicates that batteries must not be disposed of in domestic waste as they contain substances that can be damaging to the environment and health. Please dispose of batteries in designated collection points.
WEEE EXPLANATION
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
Hereby, FKA Brands Ltd, declares that this radio equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/ EU. A copy of  the Declaration of Conformity can be obtained from www.thehouseofmarley.co.uk/declaration-of- conformity

**** To prevent possible hearing damage, do not listen at high volume levels for long periods. Full instruction and warranty details can be found at
http://www.thehouseofmarley.com/instructionbooks

Marley and the Marley logo are registered trademarks of Fifty-Six Hope Road Music Limited and the use of such marks by House of Marley is under license. The Bluetooth®  word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by The House of Marley is under license.
Operating frequency band: 2402 – 2480MHz
CE Maximum radio-frequency power transmitted: -5dBm
DISTRIBUTED BY:
The House of Marley, LLC
3000 North Pontiac Trail, Commerce Township, MI 48390 the USA
Distributed in Europe by FKA Brands Ltd.,
Somerhill Business Park, Five Oak Green Rd,
Tonbridge, Kent TN11 0GP, UK.
IB-EMJT002

EM-JT002
© 2019 House of Marley, LLC.
All Rights Reserved.

References

• Bob Marley – Dedicated to the life & legacy of Tuff Gong.
• Declaration of Conformity - The House of Marley UK
• House of Marley Bluetooth Speakers, Headphones, Earbuds & Turntables Inspired by Bob Marley — One Love Movie Giveaway
• Audacity ® | Downloads
• House of Marley Bluetooth Speakers, Headphones, Earbuds & Turntables Inspired by Bob Marley - One Love Giveaway
• Declaration of Conformity - The House of Marley UK
• House of Marley | Bluetooth Speakers, Headphones & Earbuds inspired by Bob Marley

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>