MartinLogan Motion 8i Center Channel Speaker Instruction Manual

MartinLogan Motion 8i Center Channel Speaker

Specifications

• FREQUENCY RESPONSE: 70–25,000 Hz ± 3 dB
• DISPERSION: 80° x 80°
• SENSITIVITY: 89 dB @ 2.83 volts/ meter
• IMPEDANCE: 4 Ohms. Compatible with 4, 6 or 8 Ohm rated amplifiers.
• CROSSOVER FREQUENCY: 3,000 Hz
• HIGH FREQUENCY DRIVER: 1” x 1.4” (2.6cm x 3.6cm) Folded Motion Transducer with 5.25” x 1.75” (13.3cm x 4.4cm) diaphragm.
• LOW FREQUENCY DRIVERS: Two 4” (10.2cm) paper cone with stamped steel basket. Non-resonant asymmetrical chamber format. Rigid structured dust cap to reduce cone break-up modes.
• CABINET: Sealed
• COMPONENTS: Custom air core coil and low DCR steel laminate inductors. Polyester film capacitors in series and low DF electrolytic capacitors in parallel. Overall system thermal/current protection.
• RECOMMENDED AMP POWER: 20–180 watts
• BINDING POST INPUTS: Push style with banana jacks
• WEIGHT: 5 lbs. (3.85 kg)
• DIMENSIONS (H X W X D): 6” x 22.25” x 5.25” (14.2cm x 56.5cm x 13.3cm)

Introduction

Audiophile quality without the audiophile cost. Motion 2i, 4i, 6i, and 8i are compact and reasonably priced loudspeakers with excellent Folded Motion tweeters and powerful bass technology that are modelled after Martin Logan’s ultra-high-end electrostatic loudspeakers’ clarity and detail. A large surface area (much larger than a typical one-inch dome tweeter) and the tweeter’s lightning-fast response are key factors in performance. Together, they produce a smooth, refined sound with stunning dynamic range and jaw-dropping clarity certain to arouse envy in both audiophiles and non-audiophiles.

WARNING!

• Refer servicing to a qualified technician.
• To prevent fire or shock hazard, do not expose this module to moisture.
• Turn amplifier off should any abnormal conditions occur.
• Do not drive speaker beyond its rated power.

The lightning bolt flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of potentially “dangerous voltage” within the product’s enclosure that may be sufficient to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive effective August 13, 2005, we would like to notify you that this product may contain regulated materials which upon disposal, according to the WEEE directive, require special reuse and recycling processing. For this reason Martin Logan has arranged with our distributors in European Union member nations to collect and recycle this product at no cost to you.

To find your local distributor please contact the dealer from whom you purchased this product, email info@ martinlogan.com or visit the distributor locator at www. martinlogan.com.

Please note, only this product itself falls under the WEEE directive. When disposing of packaging and other related shipping materials we encourage you to recycle these items through the normal channels.

Connection

WARNING! Turn your amplifier off before making or breaking any signal connections!

These speakers are designed with easy-to-use push-style binding posts that accept bare wire or pins (fig. 2). Additionally, by removing the rubber inserts, they will accept banana plugs (fig. 3)

Assign the same color to the (+) and (–) terminals on both the speaker and the amplifier. Make certain that all connections are tight.

Installation

WARNING! Installation other than that described in the body of this document requires specific  documentation from MartinLogan.

This speaker is not magnetically shielded and therefore should not be placed directly beside or atop a CRT television.

BREAK IN

Allow approximately 72 hours of break-in at 90 dB (moderate listening levels) before any critical listening.

INSTALLING ON A FLAT SURFACE

If you have a surface that provides a wide, level, and stable platform, the speaker can be placed directly on top. When using the speaker in this configuration, affix the pads to the bottom of the speaker at the rear contact points (fig. 4). Note:.

INSTALLING ON A WALL

Note: This speaker is mountable in either a horizontal or vertical orientation. Horizontal mounting requires the use of two shoulder bolts and two wall brackets. Vertical mounting requires the use of only one shoulder bolt and mounting bracket.

Note: These instructions assume the mounting surface is standard wood frame and sheet rock construction. If you wish to mount to another type of surface, consult a bonded contractor.

Required tools (not supplied):

• Ruler
• Level
• Electric drill and 1/4” and 1/8” drill bits
• Phillips screwdriver

Horizontal Install Required hardware (included):

• (1) Installation template
• (2) Wall brackets
• (4) 1-inch Phillips sheet metal screws
• (4) Sheet rock anchors
• (2) Shoulder bolt
• (2) Wall pads

Vertical Install Required hardware (included):

• (1) Installation template
• (1) Wall brackets
• (2) 1-inch Phillips sheet metal screws
• (2) Sheet rock anchors
• (1) Shoulder bolt
• (2) Wall pads

1. Screw shoulder bolt(s) into the back of the speaker.
   Note: HORIZONTAL installation requires the use of TWO shoulder bolts (fig. 5A).
   Note: VERTICAL installation requires the use of ONE shoulder bolt (fig. 5B).

2. Affix the wall pads to the back of the speaker at the lower contact points (fig. 6).

3. Locate mounting location using a level and the installation template.
   Note: HORIZONTAL installation requires the use of TWO wall brackets.
   Note: VERTICAL installation requires the use of ONE wall bracket.

4. Mark the pilot hole locations.

5. Drill the pilot holes using a 1/8-inch drill bit. If a pilot hole DOES NOT hit a stud, widen that pilot hole using a 1/4-inch drill bit and install a wall anchor at that location (fig. 7).

6. Using the 1-inch Phillips screws, mount the wall bracket(s) as shown (fig. 7).

7. Hang the speaker, guiding the wall mount bolt into the wall bracket keyhole(s).

REMOVING THE LOGO BADGE

To remove the logo badge gently pull it away from the speaker grill (fig. 8).

Troubleshooting

No Output

• Check that all system components are turned on and source material is playing.
• Check speaker wires and connections.
• Check all interconnecting cables.
• If you are unable to resolve your problem, please contact your dealer or MartinLogan customer service (see below).

Contacting Customer Service

MartinLogan customer service is available Monday–Friday between the hours of 8am–5pm (central time) by calling 785-749-0133 or by emailing service@martinlogan.com.

General Information

WARRANTY INFORMATION

Your speakers are provided with an automatic Limited 90 Day Warranty coverage. You have the  option, at no additional charge, to receive a Limited 5 Year Warranty coverage. To obtain the Limited 5 Year Warranty coverage you need to complete and return the Certificate of Registration  to MartinLogan within 30 days of purchase. For your convenience MartinLogan also offers online warranty registration at www.martinlogan.com.

MartinLogan may not honor warranty service claims unless we have a completed Warranty Registration card on file! If you did not receive a Certificate of Registration with your new speakers you cannot be assured of having received new units. If this is the case, please contact your authorized MartinLogan dealer.

SERIAL NUMBER

Serial number is located on back of the speaker, directly beneath the binding posts. The serial number may also be found on the product carton.

SERVICE

Should you use your MartinLogan product in a country other than the one in which it was originally purchased, we ask that you note the following:

1. The appointed MartinLogan distributor for any given country is responsible for warranty servicing only on units distributed by or through it in that country in accordance with its applicable warranty.
2. Should a MartinLogan product require ser-vicing in a country other than the one in which it was originally purchased, the end user may seek to have repairs performed by the nearest MartinLogan distributor, subject to that distributor’s local servicing policies, but all cost of repairs (parts, labor, transportation) must be borne by the owner of the MartinLogan product.
3. If, after owning your speaker for six months, you relocate to a country other than the one in which you purchased your speaker, your warranty may be transferable. Contact MartinLogan for details.

FREQUENTLY ASKED QUESTIONS

How do I clean my speakers?****

Use a dust free cloth (such as a micro fiber cloth) or a soft brush to remove dust from your speakers. Do not spray any kind of cleaning agent on or in close proximity to the drivers.

Could you suggest a list of suitable electronics and cables ideal for MartinLogan speakers?****

We have no favorites and use electronics and cables quite interchangeably. We would suggest listening to a number of brands and above all else trust your ears. Dealers are always the best source for information when purchasing additional audio equipment.

Is there likely to be any interaction between my speakers and the television in my A/V system?****

Yes. These speakers are not shielded and should be kept at least 2 feet away from a CRT television.

Will exposure to sunlight affect the life or performance of my speakers?****

We recommend against placing any loudspeaker in direct sunlight. Ultraviolet (UV) rays from the sun can cause deterioration of cabinet, speaker cones, etc. Small exposures to UV will not cause a problem. Filtering of UV rays through glass will greatly reduce the negative effects.

How do I set my center channel speaker?****

Whether in front or behind the screen, always position the center channel speaker as close as you can to the image.

Can you use any speaker for center channel?****

For your center channel, you can utilize any speaker (aside from a subwoofer), but preferably, you should pick a speaker with a horizontal cabinet design rather than a vertical or square one.

What is a 3 way center channel speaker?****

The mid-range, woofer, and tweeter drivers, collectively known as the 3-way speaker, produce sound.

Should center speaker be louder than front?****

No, the middle shouldn’t be louder than the fronts when tuned properly. The center is not louder because of the setup’s numbers (or not as loud).

Should center channel have bass?****

You don’t require a lot of bass from your center channel speaker. That’s because the center channel of the majority of movie soundtracks doesn’t contain a lot of bass information.

Should I use center speaker for music?****

A center channel speaker is probably not required if you are only setting up your system for music.

Does a center channel have to match the other speakers?****

The center channel speaker needs to sound the same as the front left and right speakers for the front soundstage to be seamless.

Should center speaker be above or below screen?****

The ideal placement for the center speaker is right below the TV. This will most accurately replicate sound emanating from the TV and should be at or near ear level.

Should I set my center speaker to large or small?****

For timbre matching purposes, your Center channel should typically be set to the same size as your Front L/R speakers.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>