eufy E8220111 Security Video Doorbell Slim 1080P Battery User Guide
- June 6, 2024
- Eufy
Table of Contents
- WHAT’S INCLUDED
- PRODUCT OVERVIEW
- HOW THE SYSTEM WORKS
- STEP 1 POWERING ON THE WI-FI DOORBELL CHIME
- STEP 2 SETTING UP THE SYSTEM
- STEP 3 CHARGING YOUR DOORBELL
- STEP 4 FINDING A MOUNTING SPOT
- STEP 5 MOUNTING THE BRACKET
- STEP 6 MOUNTING THE DOORBELL
- APPENDIX 1 DETACHING THE DOORBELL
- APPENDIX 2 RECHARGING THE DOORBELL
- NOTICE
- CUSTOMER SERVICE
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
QUICK
START GUIDE
Video Doorbell Slim (1080p, Battery-Powered)
WHAT’S INCLUDED
For Video Doorbell Installation
For Wi-Fi Doorbell Chime Installation
Model: Wi-Fi Doorbell Chime
FCC ID: 2AOKB-T8020
IC: 23451-T8020
Power Plug
Note: Power plug may vary in different regions.
PRODUCT OVERVIEW
Video Doorbell (Battery-Powered)
Front view:
- Motion Sensor
- Microphone
- Camera Lens
- Ambient Light Sensor
- Status LED
- Doorbell Button
- Speaker
Rear View:
- Micro USB Charging Port
- SYNC/RESET button
- Detaching Mechanism
Operation | How-to |
---|---|
Power on | Press and release the SYNC button. |
Add doorbell to Wi-Fi
Doorbell Chime| Press and hold the SYNC button until you hear a beep.
Power off the doorbell| Quick-press the SYNC 5 times in 3 seconds.
Reset the doorbell| Press and hold the SYNC button for 10 seconds.
HOW THE SYSTEM WORKS
How the System Works
The video doorbell system includes 2 parts:
- The video doorbell at your door
- The Wi-Fi Doorbell Chime in your house
The video doorbell detects motion at your porch and allows you to answer the door anytime and anywhere. The Wi-Fi Doorbell Chime stores video clips on a microSD card (user provides it) and works as an indoor digital chime. When someone rings the doorbell, people in the house will be notified.
STEP 1 POWERING ON THE WI-FI DOORBELL CHIME
Connect the Wi-Fi Doorbell Chime to the Internet
-
Fix the power connector to Wi-Fi Doorbell Chime.
① Place the power connector over Wi-Fi Doorbell Chime in the direction the arrows indicate.
② Align the raised slots of the power connector with the notch on the base of the doorbell chime.
③ Rotate clockwise to lock the power connector in place.
-
Extend Wi-Fi Doorbell Chime’s antennas.
-
Plug Wi-Fi Doorbell Chime into an AC power supply at your desired location. The LED indicator turns solid green when the doorbell chime is ready for setup.
STEP 2 SETTING UP THE SYSTEM
Download the App and Set up the System
Download the eufy Security app from the App Store (iOS devices) or Google Play (Android devices).
Sign up for a guy Security account and follow on-screen instructions to
complete the setup.
Tap Add Device and add the following devices:
- Add the Wi-Fi Doorbell Chime.
- Add the doorbell.
STEP 3 CHARGING YOUR DOORBELL
The doorbell comes with an 80% battery level for safe transportation. Fully charge it before mounting the doorbell at your front door.
Note: The battery life varies depending on usage. In most common cases, a doorbell may have up to 15 events per day and each recording lasts 20 seconds on average. Under this scenario, the doorbell battery life can last up to 4 months.
STEP 4 FINDING A MOUNTING SPOT
Find a Mounting Spot
Take the Video Doorbell to your front door and check the live view on the eufy
Security app at the same time. Find a position where you can get the desired
field of view.
Consider the below factors:
- Check if you can reuse the existing holes and anchors on the wall or door frame.
- If you want to place the doorbell close to a side wall, make sure the wall doesn’t show up in the field of view. Otherwise, IR light will be reflected and night vision will become blurry.
- If you are drilling the mounting holes for the first time the recommended mounting height is 48″ / 1.2m from the ground.
- Use the 15° mounting wedge as a supplementary mounting bracket if you wish to see more on a specific side.
Place the Screw Hole Positioning Card against the wall to mark the position.
STEP 5 MOUNTING THE BRACKET
Mount the Doorbell on a Wooden Surface
If you’re mounting the doorbell on a wooden surface, you don’t need to pre-
drill pilot holes. Use the provided screws to secure the Mounting Bracket on
the wall. The Screw Hole Positioning Card indicates the position of the screw
holes.
What is required: Power Drill, Mounting Bracket, 15° Mounting Wedge
(Optional), Screw Packs
Mount the Video Doorbell on Surfaces Made Out of Hard Materials
- If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with a 15/64”(6mm) drill bit.
- Insert the provided anchors, and then use the provided long screws to secure the Mounting Bracket on the wall.
What is required: Power Drill, 15/64”(6mm) Drill Bit, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs
STEP 6 MOUNTING THE DOORBELL
Mount the Doorbell
Align the doorbell with the top of the mount and then snap the bottom into
place.
You’re all set!
If you want to detach the doorbell or recharge it, please refer to the
following sections.
APPENDIX 1 DETACHING THE DOORBELL
Detach the Doorbell
- Use the doorbell detaching pin provided if you wish to detach the doorbell from the Mounting Bracket.
- Insert and press the detaching pin into the hole on the bottom of the doorbell and then lift to take the bottom of the doorbell off.
What is required: Doorbell Detaching Pin
APPENDIX 2 RECHARGING THE DOORBELL
Recharge the Doorbell
Charge the doorbell with universal USB chargers that deliver 5V 1A output.
LED indication | Charging: Solid orange |
---|
Fully charged: Solid blue
Charging time| 6 hours from 0% to 100%
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures: (1)
Reorient or relocate the receiving antenna. (2) Increase the separation
between the equipment and receiver. (3) Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio / TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in fixed/mobile exposure conditions. The min separation
distance is 20cm.
Notice : Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
The following importer is the responsible party:
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: 1-800-988-7973
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance
with the essential requirements and other relevant provisions of Directive
2014/53/EU. For the declaration of conformity, visit the Web site:
https://www.eufylife.com/.
This product can be used across EU member states.
Do not use the Device in the environment at too high or too low temperature,
never expose the Device under strong sunshine or too wet environment.
The suitable temperature for T8020 and accessories is 0°C-40°C.
The suitable temperature for T8220 is -20°C-50°C.
When charging, please place the device in an environment that has a normal
room temperature and good ventilation.
It is recommended to charge the device in an environment with a temperature
that ranges from 5°C~25°C.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been
calculated based on a distance of d=20 cm between the device and the human
body. To maintain compliance with RF exposure requirements, use products that
maintains a 20cm distance between the device and the human body.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Wifi Operating Frequency Range: 2412~2472MHz (2.4G)
Wifi Max Output Power: 15.68dBm (ERIP for T8020); 15.01dBm (ERIP for T8220)
Bluetooth Operating Frequency Range: 2402~2480MHz; Bluetooth Max Output Power:
2.048dBm (EIRP)
The following importer is the responsible party (contact for EU matters only)
Anker Innovations Deutschland GmbH,Georg-Muche-Straße 3-5, 80807 München
Anker Technology (UK) Ltd, Suite B, Fairgate House, 205 Kings Road, Tyseley,
Birmingham, B11 2AA, United Kingdom
This product is designed and manufactured with high-quality materials and
components, which can be recycled and reused.
This symbol means the product must not be discarded as household waste and
should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling help protect natural resources, human health,
and the environment. For more information on the disposal and recycling of
this product, contact your local municipality, disposal service, or the shop
where you bought this product.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.”
This Class B digital apparatus complies with Canadian ICES-003.
IC RF Statement:
When using the product, maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Anker Innovations Limited. All rights reserved. eufy Security and eufy
Security Logo are trademarks of Anker Innovations Limited, registered in the
United States and other countries. All other trademarks are the property of
their respective owners.
51005002470 V01
CUSTOMER SERVICE
Warranty
12-month limited warranty
(US) +1 (800) 988 7973 Mon-Fri 9:00-17:00 (PT)
+971 42463266 (Middle East & Africa) Sun-Thu 9:00 – 17:30 (GMT+4)
Customer Support: support@eufylife.com
@Eufy Offical
@EufyOffical
eufyoffical
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>