REXING V3 Dual Camera Front and Inside Cabin Infrared Night Vision Full HD User Guide

: June 6, 2024
: Rexing

REXING V3 Dual Camera Front and Inside Cabin Infrared Night Vision Full HD

Overview

Thank you for choosing REXING! We hope you love your new product as much as we do. If you need assistance, or have any suggestions to improve it, please contact us. You can reach us via care@rexingusa.com or call us at 203-800-4466. Our support team will respond you as soon as possible.

Always a surprise in Rexing. Check us out here.

https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.com/support/registration/

| |
---|---|---

What’s in the Box

V3 Quick Start Guide
Safety Guide
USB Cable
3M Adhesive Mount
Cable Adhesive Spacer
Cable Management Tool
Rexing V3 Dashboard Camera
Car Power Connector (12ft)

Camera Overview

4 IR Lights
Power Button / Screen Toggle Button
Menu Button / Mode Button
Up Navigation Button / Front and Rear Switch Button
Down Navigation Button / Mic Button
OK (Confirm) Button / Emergency Lock Button / Record Button
Micro SD Card Slot
Power / USB Charging Port
Reset Button
Rear Camera Port (currently not support)

Screen Icons

Installation

Step 1: Install the Dash Cam

Place the 3M tape on the mount and properly orient the mount square to the roof and hood line of the vehicle.

Firmly press the mount onto the windshield. Wait at least 20 minutes before mounting the camera.

Orient the mount as shown on the illustration above.

Step 2: Insert the Memory Card

The Rexing V3 accepts [Class 10/UHS-1 or higher] Micro SD memory cards up to 256GB. You will need to insert a memory card before you can begin recording. Before inserting or removing a memory card, first ensure you’ve powered down the device. Gently push the memory card in until you hear a click, and allow the spring release to push the card out.

Step 3: Power the Camera and Format the Memory Card

Power the camera by connecting the charger to the car cigarette lighter and camera. To ensure the V3 records to your memory card properly and without error. Before you start using a new memory card, you must format the card within the camera using the format function. Always backup important data stored on the memory card before formatting.

To format the memory card, make sure you have inserted your memory card, then turn on the device by connecting to a power source. Press OK to stop recording. Then press the MENU button twice to enter the System Setup Menu.

Use the UP and DOWN navigation buttons and go to the Format setting. Press the OK button to confirm the selection.

You may now disconnect from power. The camera will shut down after 3 seconds. The camera should begin recording automatically the next time it is powered on.

Step 4: Installing the Camera onto the Windshield

Place the camera on the mount and carefully route the power cable around the windscreen and tuck it under the trim.

Plug the car charger cable to a 12V DC power outlet or the car cigarette lighter.

Connect car charger to the camera. The camera will auto-start recording once it’s powered on.

Basic Operation

Device Power

The device will be automatically powered on when plugged into a 12V accessory socket or cigarette lighter when receives a charge (i.e.: the vehicle is started).

To turn the device on manually, press and hold the Power button until the welcome screen appears.

The camera will automatically start recording when it’s powered on.

Press and hold the Power button to turn the device on manually

Power the camera On. If the camera is recording, press the OK button to stop recording.

Hold the MENU button and toggle to the desired mode. Press the MENU button once to enter the settings menu for a Mode. Press the MENU button twice to enter the System Settings (Set up).

Video Recording

The camera will automatically start recording when the device receives a charge. The LED lights and red dot will blink red device when recording. Press the OK button to stop recording.

Video Playback

Playback of videos can be done on the device or a computer.

To playback a video on the device, toggle to the Playback mode. Use the UP and DOWN navigation buttons to toggle to the desired video. Press the OK button to play.

During playback, use the OK (pause), UP navigation (rewind) and DOWN navigation (fast forward) buttons to control the video playback.

To playback a video on the computer, either use an SD card adapter or connect the device to the computer directly using the USB cable.

To playback a video using an SD card adapter, remove the memory card and insert it into an SD card adapter. Place the adapter in the computer. Then place the adapter into the computer.

To playback a video using USB cable, connect the USB Cable to the device and the computer. After the device is powered on, press the OK button to select Mass Storage.

On the computer, navigate to device drive. The videos are stored at: CARDVMOVIE. The locked videos are stored at:/CARDVMOVIERO.

Select the video to playback.

Wi-Fi Connect

Download “Rexing Connect” app from the App Store/Google Play Store.

To access or exit the WiFi feature, hold down the UP navigation button.
Open Wi-Fi settings on your phone, find “SSID” from the list, tap to connect. (Default password: 12345678)
Open the Rexing Connect app, tap “Connect” to enter the realtime video streaming page.
Once connected, the dash cam screen will switch to the camera view and will display “WiFi Connected” message. Using the Rexing Connect app, you can view a live preview of the dash cam screen, start / stop recording, as well as view and save your captures with your mobile device.

For further instruction regarding the Wi-Fi Connect feature, please visit www.rexingusa.com/wifi-connect/.

GPS Logger

When connected to the camera, it will record the speed and location of your vehicle as you drive.

You can then access these information while playing back your recordings using the GPS Video player (For windows and Mac, available at www.rexingusa.com).

The dash cam will automatically search for the GPS signal once it’s connected to the power source. Press the MENU button once and go to System Settings. Toggle the GPS setting, and select your favorite speed unit.

After a GPS signal is found, the screen icon will turn from not connected to active – as per the below icons.

GPS Signal – Searching
GPS Signal – Active
GPS Signal – Not Connected