MateStar MAT-1070 16 Inch 50W Electric Fan User Manual

USER’S MANUAL FOR ELECTRIC FAN
MODEL: MAT-1070
(PLEASE READ THIS USER’S MANUAL THOROUGHLY BEFORE USING)

Structure Diagram

1. Shroud Ring
5. Fastener for Cover
9. Back Pane
13. Support Tube| 2. Front Cove
6. Back Cover
10. Screw
14. Decorative Cover| 3. Fastener for Wing
7. Plastic Bushing
11. Up-Down Tube
15. Base| 4. Fan Blade
8. Joint
12. External Joint
16. Turning Button
---|---|---|---

Installing and Using

First step: Assemble and connect the base with assembly up-down rube and support tube Open the casing and take out the base. Then assemble the tube and cover of the up-down tube and support tube. Aim the four holes on the bottom of the support lube at the holes on the base and tighten the screws. Slip decorative cover to base alongside the tube of the support tube and adjust the up-down tube to the proper height. Then rotate tighten the external joint second step: Assemble fan blade

1. Assemble guard cover and shroud ring
   Tighten the back cover enclosure to the motor by fixing nuts. (Pay attention to direction ol rotation). Place joint of shroud ring downwards and cover the deep groove of shroud ring to the circle side ring of back cover enclosure. Then tighten the bolts at the position of joint properly by nut driver.

2. Install fan blade
   Before installing the fan blade, take out plastic bushing for protecting the motor While installing fan blade, please wedge the groove on the back of the ran blade on the spacer pin of the motor. Then tighten the fixing nut of the fan blade in the left direction.

3. Assemble front cover
   When installing the front cover, please place the decorative ring (Trademark) of the front cover in the proper position. Then insert the circle side ring of the front cover into the fleet groove of the shroud ring, which has been fixed to the back cover. Finally, screw into bolts on the joint of the shroud ring by a screwdriver.

Direction of Use

1.  The setting of WMD direction
   This fan can swing in up and down directions. The angle of facing upwards and downwards can be adjusted by slightly lifting or pressing the cover

2. Setting of turning
   Press the turning button and the fan starts to turn Then press it again and fan will stop turning

3. The setting of wind speed and wind type
   The pressing button of wind speed can adjust the speed of the wind. Pressing the button of wind type can change the type of wind.

4. The setting of timing This fan can work under 0.5h, 1h, and 2h (Maximum 2h) by timing.

Solution to Simple Failure

When starting the fan, the fan blade doesn’t work Please check whether the power plug has really been inserted into the socket or the cover has distorted, which has touched the fan blade If sound the noise when starting the fan, please check the unit as follows.

1. Fan the blade has been night installed into the axes of motor
2. The groove on the back of the cover has matched the inserting groove on the axes.
3. There are tiny defective edge ring existing around the fan blade
4. The cover has distorted, which has touched the fan blade.

Maintaining and Storing

Be sure to switch off the power supply and pull out the plug before cleaning.

1. This machine only needs common external cleaning and wiping.
2. Place into casing and store in the dry position.

Flow Chart of Product

1. Never put your finger or something into the cover to avoid any hurt.
2. Make sure to keep the fan far away from humidity, chemical, and oil
3. While cleaning, be sure to splash water and do not use oil, alcohol or chemical articles as they may cause distortion of the fan body.
4. D oo does not pull out the power supply plug by taking the power supply cord, which may lead to electrical shock or generating an electrical spark
5. Keep away from curtain, clothing or other something may affect \he fan’s working
6. Turn off all switches and pull out the power supply plug when you go out for a long time
7. Never use the fan before finishing assembly to avoid any hurts.

Attention:
If the supply cord is damaged, it must be repaired by the manufacture or its service agent or a similarly qualified in order to avoid a hazard
Before sending for maintenance, if the unit doesn’t work please check the plug of the power supply has been inserted into the socket with electricity.

Technical Parameters

PLEASE FILL IN YOUR DETAILS FOR FUTURE USE

CUSTOMER’S DETAILS

NAME OF BUYER|
ADDRESS|
TELEPHONE|
DETAILS OF SHOP

NAME OF SHOP|
RECEIPT VOUCHER NO.|
DATE OF PURCHASE|
APPLIANCE DETAILS

TYPE OF APPLIANCE|
MODEL NO.|
SERIAL NO.|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>