ENFORCER SL-1311-MA High Intensity 1Wx4 Blue LED Module User Manual
- June 6, 2024
- ENFORCER
Table of Contents
ENFORCER SL-1311-MA High Intensity 1Wx4 Blue LED Module User Manual
Features
- 4 High intensity 1-watt LEDs
- Synchronize up to 20 units
- 23 Different programmable flash patterns
- Waterproof (IP67) and vibration-resistant
- Operating life rated 100,000 hours
- Flexible input power (10~30 VDC)
Parts List
- High Intensity 1W LED Module: x1
- Mounting flange: x1
- Mounting screws: x2
- Manual: x1
- Rubber gasket: x1
Introduction
The ENFORCER SL-1311-MA/B is a High Intensity 1Wx4 LED Module strobe light
that features next generation LED technology with four 1-watt LEDs in a very
compact package.
This strobe light offers 23 selectable flash patterns, potted circuitry to be
waterproof (IP67) and vibration-resistant, multi-unit synchronization
(simultaneous or alternating), and 10~30 VDC operating voltage, making it
excellent for a wide range of security and informative applications.
Specifications
| Housing shape | Rectangular |
|---|---|
| Number of LEDs | 4 High intensity 1W LEDs |
| **Current draw*** | 560mA@12VDC / 300mA@24VDC |
| Operating voltage | 10~30 VDC |
| Electrical protection | Reverse polarity protected |
| Operating life | LEDs rated at 100,000 hours (>11 years) |
| Number of flash patterns | 23 (programmable) |
| Synchronization | Simultaneous or alternating up to 20 units |
| IP Rating | IP67 |
| Operating temperature | 22°~150° F (-30°~65° C) |
| Dimensions | 413/16″x15 /8″x11 /8″ (122x41x29 mm) |
- Figures shown are maximums. Current draw will vary depending on flash pattern.
Dimensions
Wiring and Installation
Wiring the strobe
-
Black wire: Connect to power supply negative (-) terminal or ground.
-
Red wire: Connect to power supply positive (+) terminal 10~30 VDC.
NOTE: It is recommended to fuse each unit @ 1A. -
Yellow wire:
-
Programming Flash Patterns: Connect an optional SPST momentary switch such as ENFORCER SS-032Q to program the strobe light flash patterns. See connection diagram above, and Flash Patterns on page 4 for more instructions.
-
Synchronizing Multiple Units: Connect the yellow wires of multiple units to synchronize
their flash patterns.
NOTE: All units must be set to the same flash pattern. -
Connect the yellow wires of additional units to synchronize up to 20 strobes.
-
-
White wire (optional to set alternating flash):
- Alternating Flash: Strobes can synchronize in an alternating flash pattern. For example, when Strobe A flashes ON, Strobe B will flash OFF, etc. Synchronize all strobes. Connect the white wire to the power supply only for strobes that should alternate with the others.
Mounting the strobe
- Choose a mounting surface and drill a hole large enough to allow strobe wires to pass.
- Feed the wires through the hole in the rubber gasket and the mounting surface.
- Place the mounting flange over the LED module. Check that it is properly seated on the rubber gasket and that the gasket and mounting surface form a seal to maximize weather resistance.
- Align the holes in the gasket and flange and use the self-tapping screws to secure unit in place.
Mounting Accessories: (not included)
SL-1311SM: Replacement plastic mounting flange for SL-1311-MA/B.
Flash Patterns
-
LEDs are grouped into two sets, Set 1 and Set 2.
The left pair of LEDs are Set 1; right pair of LEDs are Set 2. -
To change patterns, momentarily connect the strobe’s yellow wire to +VDC:
Each connection to power will move to the next pattern.
Hint: Use a programming switch (not included)—see Wiring and Installation on page 3. -
After changing, the flash pattern will first run one time, pause, then begin repeating.
-
Internal memory will retain last setting when power is disconnected.
Pattern #
|
Flash pattern
---|---
1
| Single (2Hz)
2
| Double (2Hz)
3
| Triple (2Hz)
4
| Quad (2Hz
5
| Randomly cycles all patterns
Alternates between Set 1 LEDs and Set 2 LEDs
6
| Single flash each set
7
| Double flash each set
8
| 4x flash each set
9
| 5x flash each set
10
| Rapid flash with fast alternation
11
| Ultra rapid flash with slow alternation
12
| Pattern 6 / Pattern 8
13
| Pattern 6 / Pattern 10
All LEDs light together
14
| Single flash
15
| Double flash
16
| 4x flash
17
| 5x flash
18
| Rapid flash
19
| Bursts of ultra rapid flash
20
| Pattern 14 / Pattern 16
21
| Pattern 14 / Pattern 18
Other
22
| Set 1 steady ON; Set 2 double flash
23
| All LEDs steady ON
California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
WARRANTY
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are
current at the time of publication. However, the SECO-LARM policy is one of
continual development and improvement. For this reason, SECO-LARM reserves the
right to change specifications without notice. SECO-LARM is also not
responsible for misprints or typographical errors.
Copyright © 2021 SECO-LARM U.S.A., Inc. All rights reserved. This material may
not be reproduced or copied, in whole or in part, without the written
permission of SECO-LARM.
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 /
949-261-2999
Fax: 949-261-7326
Website: www.seco-larm.com
E-mail: sales@seco-larm.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>