ENFORCER EV-N4506-2S4Q IP Corner-Mount Camera User Manual
- June 6, 2024
- ENFORCER
Table of Contents
EV-N4506-2S4Q
IP Corner-Mount Camera
Manual
Features:
- 1/2.8″ 5MP Sony STARVIS™ CMOS
- H.265, H.264/MJPEG, Tri-stream IP Camera
- Max. 30FPS/Full HD 5MP (2592×1944)
- Remote access via a web browser
- Network Bandwidth Control
- Event Alarm, E-mail, FTP Function
- ONVIF Profile S
- 30 Covert IR LEDs for discreet monitoring in the dark
- True Day & Night function with ICR mechanism
- Vandal-resistant metal front panel
- 3DNR & WDR
- 12VDC, PoE (IEEE802.3af)
Specifications:
| Type | Corner-Mount Camera |
|---|---|
| Sensor | 1/28″ 5MP Sony STARVISTM CMOS |
| Video encoding | H.265, H.264, MJPEG |
| Resolution | 5MP (2592×1944) |
| DNR | 2DNR |
| 3DNR | Yes |
| WDR | Yes |
| # of IR LEDs | 30 (940nm) |
| Lens | 2.8mm |
| Viewing angle | 126° |
| Minimum illumination | IR On |
| IR Off | 0.01 Lux |
| F Stop | 2. |
| Gamma correction | 0.45 |
| S/N ratio | 50dB |
| Gain control | Auto |
| White balance | Auto |
| Operating voltage | 12VDC, PoE (IEEE802.3af) |
| Current draw (IR Off) | 140mA max. |
| IP Rating | IP65 |
| Operating temperature | 14°-122° F (-10°-50° C) |
| Dimensions | 7112″ x5,/2″x111/16″ (190x140x43 mm) |
| Weight | 13.75-oz (390g) |
Parts List:
| 1x Camera | 1x Camera cover | 1x CD | 4x Mounting screws |
|---|---|---|---|
| 1x Pigtail connector | 3x Security screws | 1x Security wrench | 1x Manual |
Overview:
*IMPORTANT: Do not cut DC jack or RJ45 jack as the
warranty will be voided.
Before Starting:
- Please read this manual carefully and keep it for future reference.
- Use the camera within the given temperature and electrical limits.
- Do not point the camera at the sun. Heat could damage the camera, even when not in use.
- Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
- Do not open or disassemble the camera. There are no field-serviceable parts inside.
- Do not drop the camera or subject it to strong vibrations.
Installation:
-
Use the included security wrench to loosen the screws and remove the camera cover from the camera.
-
Run a 12VDC power supply wire and cable with an RJ45 jack through the wall at the corner where the camera is to be mounted.
-
Execute “IP Manager” on the PC.
-
Press the “Find” button. IP cameras connected tothe same router will be searched and listed. This may take several seconds. The Default IP address is 192.168.1.30.
-
Right-click the desired product, and press “IP Change”.
-
Use web port number 80. This is an internal port.
-
IP address: You may use Dynamic IP or you may set Static IP as below:
-
The typical IP setting is as follows.
-
IP address.: 192.168.1.10 (you can change the last column)
Netmask: 255.255.255.0
Gateway: 192.168.1.1
DNS1/2: You can copy the PC’s network properties.
This is for internet environments. -
Input “admin” for User ID and password
NOTE: It is recommended that you change the default password. -
Press “Change” to save settings and allow 10s for changes to appear.
-
Right-click the desired device and click “Open Web Page”.
-
Enter Username / Password.
-
Click “Live” on the top right of the screen.
-
Click yes for “ActiveX Control”.
-
After the installation of Active X, you will be able to view the live feed only with Internet Explorer. Visit http://www.seco-larm.com/EV-N4506-2S4Qfor the Web Admin Manual.
Troubleshooting:
The screen in blank|
- Check that the camera is powered up.
- Check that the power supply’s polarity is correct.
- Check that the monitor is powered up.
- Check that the video cable connecting the camera to the monitor is connected properly.
---|---
The screen image is dim|
- Clean the lens using a soft, clean cloth.
- Check that the light source is adequate.
The screen image has poor contrast.|
- Adjust the monitor’s contrast knob.
- Change the position of the camera.
The screen image flickers.|
- Change the position of the camera.
The screen image is distorted.|
- Change the position of the camera.
The camera case is hot.|
- Check that the correct power supply is in use
IR LEDs do not turn on.|
- Check that the correct power supply is in use
IMPORTANT : Users and installers of this product are responsible for
ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-
LARM will not be held responsible for the use of this product in violation of
any current laws or statutes.
California Proposition 65 Warning: These products may contain chemicals
that are known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any change
to the antenna or the device could result in the device exceeding the RF
exposure requirements and void the user’s authority to operate the device.
WARRANTY: This SECO-LARM product is warranted against defects in material
and workmanship while used in normal service for three (3) years from the date
of sale to the original customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned,
transportation prepaid, to SECO-LARM. This Warranty is void if the damage is
caused by or attributed to acts of God, physical or electrical misuse or
abuse, neglect, repair or alteration, improper or abnormal usage, or faulty
installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects
in material and workmanship. The sole obligation of SECO-LARM and the
purchaser’s exclusive remedy shall be limited to the replacement or repair
only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any
special, collateral, incidental, or consequential personal or property damage
of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and
improvement. For that reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for
misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their
respective owners. Copyright © 2021 SECO-LARM U.S.A., Inc. All rights
reserved.
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: 949-261-2999 |
800-662-0800
Website: www.seco-larm.com
Email: sales@seco-larm.com
PIKSR1
MI_EV-N4506-2S4Q_210430.docx
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>