Hunts Office Framery Control Unit User Manual
- June 6, 2024
- Hunts Office
Table of Contents
FRAMERY CONTROL UNIT
USER MANUAL
Framey
Patamäenkatu 7, 33900 Tampere, Finland
Info framery.com
GENERAL NOTES
PRODUCT IS ONLY FOR FRAMERY PRODUCT USE
COPYRIGHT
THE INFORMATION CONTAINED HERE IS PROPRIETARY TECHNICAL INFORMATION OF
FRAMERY. TRANSMITTING, REPRODUCTION, DISSEMINATION AND EDITING OF THIS
DOCUMENT AS WELL AS UTILIZATION OF THE CONTENT ARE FORBIDDEN WITHOUT
PERMISSION.
Version control:
| 9.2.2021 | v 0.1 (DRAFT) | Pirjo Laurila |
|---|---|---|
Preface
This instruction manual describes the use of Framery Control Unit. It is
exclusively for use in Framery’s phone booths, like Framey One, and other
future Framery meeting space products, pods.
The user instructions contain the following information: General information
about the purpose and content of the instructions Intended use and use
conditions Compliance statements with list the FCC rules that are applicable
to the transmitter. RF exposure conditions Advice on further testing needed
for the host and instructions to end user A list of antennas included in the
application Assembly instructions of Control Unit
Intended use and use conditions
The Framery Control Unit model 9000456-01A is intended for use in Framery One pod for short term indoor commercial and household use.
Warning: WARNING To reduce the risk of burns, fire, electric shock, or injury to persons:
- Use this product only for its intended use as described in the user instructions.
- Do not use attachments not recommended by the manufacturer.
Non-conventional use
Any use or maintenance of the product that is not specifically allowed in the installation, maintenance, troubleshooting or user instructions is prohibited, including the following:
- Installation, maintenance or disassembly of the Control Unit without reading and understanding the instructions for those actions
- Use of the Control Unit for any other host except Framery One
- Making alterations to the Control Unit
- Using the Contorl Unit in spite of obvious defects or damage
- Using the Contorl Unit or host product outdoors or in conditions where the temperature or air quality is not safe
Ambient conditions for use
The host product is intended to be used in the following conditions:
- Ambient temperature: +15°C … +30°C (59°F … 86°F)
- Humidity: max. 50%
- Sufficient air quality surrounding the product
Regulatory conditions for use
- According to definition on FCC 2.1093 this is a portable device and the following conditions must be met:
- 1. This Approval is applicable for a portable device. The antenna installation and operating configurations of this transmitter, including any applicable source-based timeaveraging duty factor, antenna gain and cable loss must satisfy Requirements of 2.1093 for general population/uncontrolled exposures.
- 2. The EUT is a portable device and may not transmit simultaneously with any other antenna or transmitter without shown to be compliant with requirements on 2.1093 and other applicable sections of FCC Requirements.
- 3. This device contains LTE and BLE modules and must not transmit simultaneously with any other antenna or transmitter.
- 4. The host end product must include a user manual that clearly defines operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines.
- 5. This transmitter has been tested and compliant with RF exposure for general public use limb and body exposure limits. Integration should be such the end user body is prevented from approaching the Control unit closer than 10 mm. Limb contact on Contorl Unit display is allowed. This information is needed for the host product manufacturer to provide to end users in their endproduct manuals.
- 6. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, maximum antenna gain (including cable loss) must not exceed:
Operating Band
GSM850
GSM1900
WCDMA BAND II
WCDMA BAND IV
WCDMA BAND V
LTE BAND 2
LTE BAND 4
LTE BAND 5
LTE BAND 7
LTE BAND 12
LTE BAND 13
LTE BAND 25
LTE BAND 26(814-824)
LTE BAND 26(824-849)
LTE BAND 38
LTE BAND 41
BLE| FCC Max Antenna Gain (dBi)
8.60
10.19
8.00
5.00
9.42
8.00
5.00
9.41
8.00
8.70
9.16
8.00
9.36
9.41
8.00
8.00
5.00| IC Max Antenna Gain（dBi）
7.44
10.19
8.00
5.00
8.26
8.00
5.00
8.25
8.00
7.76
8.09
8.00
NA
8.25
8.00
8.00
5.00
---|---|---
Compliance statements FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: any changes or modifications not expressly approved by Framery
Oy could void the user’s authority to operate the equipment.
The Control Unit is a portable device per FCC 2.093. The Control Unit is for
the use in Framery One Phone Booth only (final host product) and is not
allowed to be integrated into any other device. The final host product
requires Part 15 Subpart B compliance testing with the modular transmitter
installed.
Compliance markings (labeling) FCC
For this device, OEM integrators must be provided with labelling instructions
of finished products. Please refer to KDB784748 D01 v07, section 8. Page 6/7
last two paragraphs: A certified device has the option to use a permanently
affixed label, or an electronic label. For a permanently affixed label, the
devace must be labeled with an FCC ID – Section 2.926 (see 2.2 Certification
(labeling requirements) above). The OEM manual must provide clear instructions
explaining to the OEM the labeling requirements, options and OEM user manual
instructions that are required (see next paragraph).
The Control Unit has electronic label information as follows: FCC ID:
2AX4J9000456 containing FCC ID: 2AX4J201906EG21G.
This is available from Control Unit main menu > Compliance information. It is available for the end user when the Control Unit is integrated to the finished product. This guidance on how to access to the electronic labelling information on Control Unit must be presented to the end user in the final product (Framery One ) user manual.
According KDB 784748 D02 when e-labeling is used, a physical temporary label
is also required on the product, or a label on the packaging, at the time of
importation, marketing, and sales. The physical label can be a summary version
of the required regulatory information, such that the product can be
identified as complying with the FCC’s equipment authorization requirements.
The information may simply be the FCC ID for products subject to
certification.
Products imported that are already packaged for sale and have a physical
temporary label will satisfy this requirement. However, for products imported
in bulk and not packaged individually, it is acceptable to use a temporary
removable adhesive label on the product, or temporary or permanent labels on
the shipping packaging or protective bags. Any removable adhesive label shall
be of a type intended to survive normal shipping and handling.
Advice on Further Testing of the Host and Instructions to the End User
FCC
The integrator has to be aware not to provide information to the end user
regarding how to install or remove this device in the user’s manual of the end
product which integrates this device. The end user manual shall include all
required regulatory information/warning as show in this manual.
The final host / device combination may also need to be evaluated against the
FCC Part 15B criteria for unintentional radiators in order to be properly
authorized for operation as a Part 15 digital device.
The user’s manual or instruction manual for an intentional or unintentional
radiator shall give the following statement and caution the user that changes
or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
To ensure compliance with all non-transmitter functions the host manufacturer
is responsible for ensuring compliance with the device installed and fully
operational. For example, if a host was previously authorized as an
unintentional radiator under the Supplier’s Declaration of Conformity
procedure without a transmitter certified device and a device is added, the
host manufacturer is responsible for ensuring that the after the device is
installed and operational the host continues to be compliant with the Part 15B
unintentional radiator requirements.
In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form.
Compliance statements and markings IC
IRSS-GEN
“This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.”
The host product shall be properly labeled to identify the device within the
host product. The Innovation, Science and Economic Development Canada
certification label of a device shall be clearly visible at all times when
installed in the host product
Devices with an integrated display screen may have the required label
information represented electronically in an e-label instead of on a physical
label or nameplate.
The Control Unit has electric label information as follows:
Framery Control Unit
Model #9000456-01A
IC: 26702-9000456 containing IC: 26702-201906EG21G
IC: 26702-9000456 contient IC: 26702-201906EG21G
This is available from Control Unit main menu > Compliance information. It is
available for the end user when the Control Unit is integrated to the finished
product. This guidance on how to access to the electronic labelling
information on Control Unit must be presented to the end user in the final
product user manual.
Framery Control Unit
Model #9000456-01A
IC: 26702-9000456 containing IC: 26702-201906EG21G
IC: 26702-9000456 contient IC: 26702-201906EG21G
List of antennas
Framery Control Unit has three antennas, which has been integrated to PWB. First antenna is LTE Mains antenna, second LTE diversity antenna and third BLE antenna.
LTE antenna operation frequency: 824 849MHz (GSM 850)
1850 1910MHz (GSM 1900)
1850 1910MHz (WCDMA 2)
1710 1755MHz (WCDMA 4)
824 849MHz (WCDMA 5)
1850 1910MHz (LTE 2)
1710 1755MHz (LTE 4)
824 849MHz (LTE 5)
699 716MHz (LTE 7)
777 878MHz (LTE 12)
788 798MHz (LTE 13)
1850 1915MHz (LTE 25)
814 849MHz (LTE 26)
2496 2690MHz (LTE 41)
Bluetooth antenna operation frequency: 2400 2483.5MHz
LTE Main antenna type: Omnidirectional antenna, Maximum antenna gain [G]:
+5dBi
LTE Main antenna type: Omnidirectional antenna, Maximum antenna gain [G]:
+5dBi
Bluetooth antenna type: Omnidirectional antenna, Maximum antenna gain [G]:
+5dBi
Assembly instructions
To assemble the Control Unit using prefabricated parts follow the guidance below. Control Unit prefabricated parts are listed below:
- Install printed circuit board (5) to display frame (3) using 6 screws (6).
- Install back frame (7) to display frame (3) with 3 screws (8).
To assemble the Control Unit to the host product Framery One follow the guidance below.
This information is available on Framery One Installation Instructions.
References
- The Framery | SERVING MILITARY AND CIVILIAN CUSTOMERS WORLDWIDE FOR 31 YEARS
- Contact - Framery Design your pod Get a quote Design your pod Get a quote Design your pod Get a quote Facebook Twitter LinkedIn Instagram
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>