iRacing Hyundai Veloster N TC Racing Car User Manual
- June 12, 2024
- iRacing
Table of Contents
iRacing Hyundai Veloster N TC Racing Car
Product Information
Chassis| McPherson Strut Front Suspension, 4-Arm Multi-Link Rear
Suspension
---|---
Length| 4006 mm / 181 in
Width| 1950 mm / 77 in
Wheelbase| 2650 mm / 104 in
Dry Weight| 1365 kg / 3010 lbs
Wet Weight (with driver)| 1468 kg / 3238 lbs
Power Unit| Turbocharged DOHC 4-Cylinder
Displacement| 2.0 Liters / 122 cid
Torque| 330 lb-ft / 450 Nm
Power| 350 bhp / 260 kW
RPM Limit| 7,000
Product Usage Instructions
Getting Started
Before starting the car, it is recommended to map controls for Brake Bias adjustment. While this is not mandatory, this will allow you to make quick changes to the brake bias to suit your driving style while on track.
Loading an iRacing Setup
Upon loading into a session, the car will automatically load the iRacing Baseline setup [baseline.sto]. If you would prefer one of iRacing’s pre-built setups that suit various conditions, you may load it by clicking Garage > iRacing Setups > and then selecting the setup to suit your needs.
If you would like to customize the setup, simply make the changes in the garage that you would like to update and click apply. If you would like to save your setup for future use click Save As on the right to name and save the changes.
To access all of your personally saved setups, click My Setups on the right side of the garage.
If you would like to share a setup with another driver or everyone in a session, you can select Share on the right side of the garage to do so.
If a driver is trying to share a setup with you, you will find it under Shared Setups on the right side of the garage as well.
Dash Configuration
The Hyundai Veloster N TC features a digital dash display with three main pages. Pages change automatically based on what the car is doing to display the most relevant data at any given time. The first display page is active when the car is stationary and in Neutral.
Page 1| Gear Indicator
Tachometer
Water Temperature
Oil Temperature
Exhaust Gas Temp
Oil Pressure
---|---
Dear iRacing User,
Touring car racing remains one of the world’s most popular forms of road
racing, combining approachable front-wheel drive cars with some of the most
legendary circuits on the planet. The result is an aggressive, elbows-out form
of road racing that proves to be just as much fun for the drivers behind the
wheel as it is to watch for the fans in the seats.
Launched in 2019, the Hyundai Veloster N TC was built for Hyundai’s North American teams to better reflect Hyundai’s presence in the market. Based on the Hyundai i30 N TC that kicked off the brand’s modern dominance of the discipline, the Veloster shares a majority of its components with its predecessor, and quickly shared similar successes on the track as well. In 2019, its first season as a part of the IMSA Michelin Pilot Challenge, Velosters campaigned by the prominent Bryan Herta Autosport team went 1-2 in the final standings with a combined four race wins.
Thanks again for your purchase, and we’ll see you on the track!
TECH SPECS
Introduction
The information found in this guide is intended to provide a deeper understanding of the chassis setup adjustments available in the garage, so that you may use the garage to tune the chassis setup to your preference.
Before diving into chassis adjustments, though, it is best to become familiar with the car and track. To that end, we have provided setups for each track commonly raced by these cars. To access the provided setups, simply open the Garage, click iRacing Setups, and select the appropriate setup for your track of choice. If you are driving a track for which a dedicated setup is not included, you may select a setup for a similar track to use as your baseline. After you have selected an appropriate setup, get on track and focus on making smooth and consistent laps, identifying the proper racing line and experiencing tire wear and handling trends over a number of laps.
Once you are confident that you are nearing your driving potential with the included baseline setups, read on to begin tuning the car to your handling preferences.
GETTING STARTED
Before starting the car, it is recommended to map controls for Brake Bias
adjustment. While this is not mandatory, this will allow you to make quick
changes to the brake bias to suit your driving style while on track.
Once you load into the car, depress the clutch and select 1st gear. Slowly
release the clutch while applying the throttle to drive away. The Hyundai
Veloster N TC features six forward gears and one reverse gear, and does not
require clutch use once the vehicle is in motion for upshifts or downshifts. A
clutch is necessary when coming to a stop to prevent stalling the engine and
shifting into reverse if necessary. To upshift, simply press the assigned
button to select the next higher gear. To downshift, press the downshift
button to select the next lower gear.
LOADING AN iRACING SETUP
Upon loading into a session, the car will automatically load the iRacing
Baseline setup [baseline.sto]. If you would prefer one of iRacing’s pre-built
setups that suit various conditions, you may load it by clicking Garage >
iRacing Setups > and then selecting the setup to suit your needs.
If you would like to customize the setup, simply make the changes in the
garage that you would like to update and click apply. If you would like to
save your setup for future use click “Save As” on the right to name and save
the changes.
To access all of your personally saved setups, click “My Setups” on the right
side of the garage.
If you would like to share a setup with another driver or everyone in a
session, you can select “Share” on the right side of the garage to do so.
If a driver is trying to share a setup with you, you will find it under
“Shared Setups” on the right side of the garage as well.
Dash Configuration
The Hyundai Veloster N TC features a digital dash display with three main pages. Pages change automatically based on what the car is doing to display the most relevant data at any given time. The first display page is active when the car is stationary and in Neutral.
Page 1
- Gear Indicator: The center of the display shows the selected gear (Neutral, for this page).
- Tachometer: Surrounding the gear indicator is a tachometer displaying engine RPM.
- Water Temperature: The upper left of the display shows the Engine’s Water Temperature
- Oil Temperature: The upper right of the display shows the Engine’s Oil Temperature
- Exhaust Gas Temp: The lower left of the display shows the engine’s Exhaust Gas Temperature.
- Oil Pressure: The lower right of the display shows the Engine Oil Pressure.
The second display page activates when the car is stationary but 1st gear is selected. This page is helpful for standing starts.
Page 2
- Tachometer: The upper part of the display shows the engine RPM. The upper part of the display shows the engine RPM.
- pinlet (mBar): The center of the display shows the current engine inlet pressure. As RPM is increased for a start, this bar will change to green when inlet pressure is optimum for a launch.
- CarSpeed: The black bar in the lower left shows the vehicle’s speed.
- Gear: The green bar shows the currently selected gear.
- Clutch: The red bar in the center displays the current clutch pedal position.
- Pedal: The second red bar displays the current throttle pedal position.
- tExhaust: The black bar in the lower right displays the Exhaust Gas Temperature.
Once the vehicle is moving, the dash will change to the third page. This page displays information relevant for racing, and is the most commonly seen dash page.
Page 3
- Speed: Current vehicle speed is shown in the upper left above the Hyundai Motorsport logo.
- Time: Time elapsed on the current lap.
- Tachometer: The upper part of the display shows the engine RPM.
- tWater: Engine Water Temperature is shown on the upper left of the lower section.
- pOil: Engine Oil Pressure is shown in the lower left, below Water Temperature.
- Gear: The currently selected gear is shown in the center of the display.
- timeSlip: This shows the difference between the current lap and the session’s best lap.
- lastLap: The lap time for the previously completed lap is shown here.
- Lap: The number of laps completed in the current session is shown in the lower right. This value does not reset when returning to pit road.
When the pit limiter is active, Page #3 will change from black to green to show the Pit Speed Limiter is active.
Advanced Setup Options
This section is aimed toward more advanced users who want to
dive deeper into the different aspects of the vehicle’s setup. Making
adjustments to the following parameters is not required and can lead to
significant changes in the way a vehicle handles. It is recommended that any
adjustments are made in an incremental fashion and only singular variables are
adjusted before testing changes.
Tires
COLD AIR PRESSURE
Air pressure in the tire when the car is loaded into the world. Higher
pressures will reduce rolling drag and heat buildup, but will decrease grip.
Lower pressures will increase rolling drag and heat buildup, but will increase
grip. Higher speeds and loads will require higher pressures, while lower
speeds and loads will see better performance from lower pressures. Cold
pressures should be set to track characteristics for optimum performance.
HOT AIR PRESSURE
Air pressure in the tire after the car has returned to the pits. The
difference between Cold and Hot pressures can be used to identify how the car
is progressing through a run in terms of balance, with heavier-loaded tires
seeing a larger difference between Cold and Hot pressures. Ideally, tires that
are worked in a similar way should build pressure at the same rate to prevent
a change in handling balance over the life of the tire, so Cold pressures
should be adjusted to ensure that similar tires are at similar pressures once
up to operating temperature.
TIRE TEMPERATURES
Tire carcass temperatures, measured via Pyrometer, once the car has returned
from the pits. Wheel Loads and the amount
of work a tire is doing on-track is reflected in the tire’s temperature, and
these values can be used to analyze the car’s
handling balance. Center temperatures are useful for directly comparing the
work done by each tire, while the Inner and Outer temperatures are useful for
analyzing the wheel alignment while on track. These values are measured in
three zones across the tread of the tire.
TREAD REMAINING
The amount of tread remaining on the tire once the car has returned from the
pits. Tire wear is very helpful in identifying
any possible issues with alignment, such as one side of the tire wearing
excessively, and can be used in conjunction with tire temperatures to analyze
the car’s handling balance. These values are measured in three zones across
the tread of the tire.
Chassis
FRONT
%
FRONT WEIGHT
The percentage of total vehicle weight in the garage across the front axle.
Higher Nose Weight values will induce understeer when cornering and promote
straight-line stability, while lower Nose Weight values will increase
oversteer while cornering. This is not directly adjustable and is altered by
other adjustments, such as Fuel Level.
CROSS WEIGHT
Cross weight is the amount of weight on the car’s Left-Rear and Right-Front
tires relative to the entire weight of the car, displayed in percent. This is
adjusted via the corner Spring Perch Offset settings to move weight between
the four wheels. It’s best to keep this value as close to 50.0% as possible to
ensure symmetrical handling characteristics.
ANTI-ROLL BAR DIAMETER
The Anti-Roll Bar Diameter setting controls the roll stiffness in the front
suspension. Larger front Anti-Roll Bar sizes will increase roll stiffness and
induce understeer, while smaller Anti-Roll Bar sizes can reduce understeer by
softening the suspension’s roll stiffness.
ANTI-ROLL BAR ARM LENGTH
The length of the Anti-Roll Bar arms can be adjusted to fine tune the
effective stiffness of the bar without changing the diameter. Longer arms
(higher number values) will create a softer effective stiffness than shorter
arms (lower number values).
STEERING RATIO
The Steering Ratio is a numerical value relating steering wheel angle to road
wheel angle. This ratio can be thought of as the degrees of driver steering
input needed to produce one degree of turn of the front wheels. For example, a
steering ratio of
“10” can be thought of as requiring 10° of steering input to turn the wheels
1°. A steering ratio with a lower ratio will feel more responsive or faster
and will require less steering input to reach the tire angle needed to
navigate a corner. Another way to think about this is that for the same
steering wheel input, a lower steering ratio will produce more road wheel
turn. The real-world setting for the Hyundai Veloster N TC is 10, however an
option of 14 is available to make the steering feel more like what is found in
the other vehicles in this class.
NET TOE-IN
Toe is the angle of the front wheels, when viewed from above, relative to the
centerline of the chassis. Positive values for this setting are Toe-In,
negative values are Toe-out. Toe-in is when the front of the wheels are closer
to the centerline than the rear of the wheels, and Toe-out is the opposite. On
the front end, adding toe-out will increase straight-line stability as well as
increasing the slip angle on the inside tire when turning. This can aid in
turn-in response but can make it easier to over-slip the tire and lose grip
with too much steering angle. Toe-in at the front will reduce turn-in
responsiveness but will reduce temperature buildup in the front tires.
ABS SET TING
The Anti-Lock Brake System (ABS) can be changed to one of five settings to
suit different situations. Setting 1 is used for Dry conditions, Setting 2 is
for Damp conditions, and Setting 3 is for Wet conditions. Setting 4 is useful
for Safety Car situations and Setting 5 is for emergencies and puts the system
into “Limp” mode. This value can be adjusted via the F8 Black Box.
BRAKE PRESSURE BIAS
Brake Bias is the percentage of braking force that is being sent to the front
brakes. Values above 50% result in more pressure being sent to the front,
while values less than 50% send more force to the rear. This should be tuned
for both driver preference and track conditions to get the optimum braking
performance for a given situation.
REAR BRAKE VALVE
The Rear Brake Valve setting controls the amount of braking pressure that goes
to the rear wheels, allowing rear brake adjustment without altering the amount
of pressure that goes to the front wheels. Increasing the Rear Brake Valve
value will generate more brake line pressure to the rear wheels, producing a
similar effect to reducing front brake bias, without reducing the braking
force to the front wheels. Reducing the Rear Brake Valve setting will reduce
brake pressure to the rear wheels, similar to shifting the brake bias forward.
LAUNCH RPM LIMIT
For standing starts, the RPM limiter can be adjusted up or down to optimize
launch for different grip levels. Higher limits can prevent the engine from
bogging down, but can spin the front tires more easily.
CENTER SPLIT TER HEIGHT
The front splitter ground clearance is shown in the garage. This is not
directly adjustable but will change based on other settings in the garage.
There are no tech-inspection checks on this value and it only serves as a
reference for the car’s attitude under static conditions.
FRONT CORNERS
CORNER WEIGHT
The weight underneath each tire under static conditions in the garage. Correct
weight arrangement around the car is crucial for optimizing a car for a given
track and conditions. Individual wheel weight adjustments and crossweight
adjustments are made via the spring perch offset adjustments at each corner.
RIDE HEIGHT
Distance from ground to a reference point on the chassis. Since these values
are measured to a specific reference point on the car, these values may not
necessarily reflect the vehicle’s ground clearance, but instead provide a
reliable value for the height of the car off of the race track at static
values. Adjusting Ride Heights is key for optimum performance, as they can
directly influence the vehicle’s aerodynamic performance as well as mechanical
grip. Increasing front ride height will decrease front downforce
as well as decrease overall downforce, but will allow for more weight transfer
across the front axle when cornering. Conversely, reducing ride height will
increase front and overall downforce, but reduce the weight transfer across
the front axle. Minimum legal front ride height is 70 mm.
SPRING PERCH OFFSET
Spring perch offset is used to adjust ride height and corner weight by
changing the preload on the spring under static conditions. Decreasing the
value increases preload on the spring, adding weight to its corner and
increasing the ride height at that corner. Increasing the value does the
opposite, reducing height and weight on a given corner. These should be
adjusted in pairs (left and right together, for example) or with all four
spring preload adjustments in the car to prevent crossweight changes while
adjusting ride height.
SPRING RATE
This setting determines the installed corner spring stiffness. Stiffer springs
will result in a smaller variance in ride height between high and low load
cases and will produce superior aerodynamic performance through improved
platform control; however, they will also result in increased tire load
variation which will manifest as a loss in mechanical grip. The drawbacks of
stiffer springs will become more pronounced on rougher tracks where softer
springs will result in increased overall performance. Corner spring changes
will influence both roll and pitch control of the platform and ARB changes
should be considered when altering corner spring stiffnesses in order to
retain the same front to rear roll stiffness and handling balance. When
reducing corner spring stiffness the ARB stiffness should be increased to
retain the same roll stiffness as before the spring change. Spring perch
offsets must be adjusted to return the car to the prior static ride heights
after any spring rate change.
BUMP STIFFNESS
Bump stiffness affects how resistant the shock is to compression (reduction in
length), usually in chassis movements as a result of driver input (steering,
braking, & throttle) and cornering forces. Higher Bump Stiffness values will
slow suspension travel and increase wheel load during travel, but reduces how
well the suspension can handle bumps. Reducing Bump Stiffness can help the
suspension absorb bumps, but can reduce how responsive the chassis feels to
the driver.
REBOUND STIFFNESS
Rebound stiffness affects how resistant the shock is to extension (increase in
length), typically during body movement as a result of driver inputs. Higher
rebound values will slow extension of the shock, lower values will allow the
shock to extend faster. Higher rebound values can better control aerodynamic
attitude but can result in the wheel being unloaded when the suspension can’t
extend enough to maintain proper contact with the track. Excessive rebound can
also lead to unwanted oscillations caused by the wheel bouncing off of the
track surface instead of staying in contact.
CAMBER
Camber is the vertical angle of the wheel relative to the center of the
chassis. Negative camber is when the top of the wheel is closer to the chassis
centerline than the bottom of the wheel, positive camber is when the top of
the tire is farther out than the bottom. Due to suspension geometry and corner
loads, negative camber is desired on all four wheels. Higher negative camber
values will increase the cornering force generated by the tire, but will
reduce the amount of longitudinal grip the tire will have under braking.
Excessive camber values can produce very high cornering forces but will also
significantly reduce tire life, so it is important to find a balance between
life and performance. Increasing front camber values will typically result in
increased front axle grip during mid to high speed cornering but will result
in a loss of braking performance and necessitate a rearward shift in brake
bias to compensate.
REAR CORNERS
CORNER WEIGHT
This displays the weight on each wheel while sitting in the garage under
static conditions. Useful for determining weight distribution during chassis
adjustments.
RIDE HEIGHT
Distance from ground to a reference point on the rear of the chassis.
Increasing rear ride height will decrease rear downforce but will increase
overall downforce and will allow for more weight transfer across the rear axle
when cornering. Conversely, reducing ride height will increase rear downforce
percentage but reduce overall downforce while reducing the weight transfer
across
the rear axle. Rear ride height is a critical tuning component for both
mechanical and aerodynamic balance, and static rear ride heights should be
considered and matched to the chosen rear corner springs for optimal
performance. Minimum legal rear ride height is 70 mm while maximum legal rear
ride height is 85 mm.
SPRING PERCH OFFSET
Spring perch offset is used to adjust ride height and corner weight by
changing the preload on the spring under static conditions. Decreasing the
value increases preload on the spring, adding weight to its corner and
increasing the ride height at that corner. Increasing the value does the
opposite, reducing height and weight on a given corner. These should be
adjusted in pairs (left and right together, for example) or with all four
spring preload adjustments in the car to prevent crossweight changes while
adjusting ride height.
SPRING RATE
Similar to the front axle, stiffer springs will result in a smaller variance
in ride height between high and low loads and will produce better aerodynamic
performance through improved platform control at the expense of mechanical
grip. Spring stiffness should be matched to the needs of the racetrack and set
such that the handling balance is consistent between high and low speed
cornering. Increasing rear spring rate will allow for a lower static rear
height which will reduce rear weight transfer during slow speed cornering
while maintaining or even increasing the rear ride height in high speed
cornering to shift the aerodynamic balance forwards and reduce understeer.
Spring perch offsets must be adjusted to return the car to the prior static
ride heights after any spring rate change.
BUMP STIFFNESS
Bump stiffness affects how resistant the shock is to compression (reduction in
length), usually in chassis movements as a result of driver input (steering,
braking, & throttle) and cornering forces. Higher Bump Stiffness values will
slow suspension travel and increase wheel load during travel, but reduces how
well the suspension can handle bumps. Reducing Bump Stiffness can help the
suspension absorb bumps, but can reduce how responsive the chassis feels to
the driver.
REBOUND STIFFNESS
Rebound stiffness affects how resistant the shock is to extension (increase in
length), typically during body movement as a result of driver inputs. Higher
rebound values will slow extension of the shock, lower values will allow the
shock to extend faster. Higher rebound values can better control aerodynamic
attitude but can result in the wheel being unloaded when the suspension can’t
extend enough to maintain proper contact with the track. Excessive rebound can
also lead to unwanted oscillations caused by the wheel bouncing off of the
track surface instead of staying in contact.
CAMBER
As with the front of the car it is desirable to run significant amounts of
negative camber in order to increase the lateral grip capability. Since the
rear wheels are not driven and are typically under less load than the fronts,
the rear tires will usually see better performance with less camber than the
front tires. More rear camber will increase cornering forces from the tires as
increasing wear and heat buildup, but will decrease maximum braking capacity
from the tires.
REAR
FUEL LEVEL
Fuel level is the amount of fuel in the fuel tank when the car leaves the
garage.
ANTI-ROLL BAR DIAMETER
The Anti-Roll Bar Diameter setting controls the roll stiffness in the rear
suspension. Larger rear Anti-Roll Bar sizes will increase roll stiffness and
induce oversteer, while smaller Anti-Roll Bar sizes can reduce oversteer by
softening the suspension’s roll stiffness.
ANTI-ROLL ARM LENGTH
The length of the Anti-Roll Bar arms can be adjusted to fine tune the
effective stiffness of the bar without changing the diameter. Longer arms
(higher number values) will create a softer effective stiffness than shorter
arms (lower number values).
NET TOE-IN
Toe is the angle of the rear wheels, when viewed from above, relative to the
centerline of the chassis. Positive values for this setting are Toe-In,
negative values are Toe-out. Toe-in is when the front of the wheels are closer
to the centerline than the rear
of the wheels, and Toe-out is the opposite. On the rear end, adding toe-out
will decrease straight-line stability and can induce oversteer suddenly in
some cases. Toe-in at the rear will reduce turn-in responsiveness but will
increase straight-line stability.
REAR WING SET TING
The rear wing’s angle of attack can be changed via the Rear Wing Setting.
Higher angles will cause the wing to produce more downforce and shift aero
balance rearward, inducing understeer in mid- to high-speed corners, but will
increase drag. Lower angles will reduce the amount of downforce generated and
shift aero balance forward, increasing oversteer in mid- and high-speed
corners, but will also reduce the amount of drag produced by the wing. Angle
settings are available from -4.0° to +4.0°, however it is important to note
that all angles will produce downforce, and negative angles do not produce
lift.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>