Pioneer Electronics TS-ME770FS TS-ME770FC Instruction Manual
- June 6, 2024
- Pioneer
Table of Contents
Pioneer Electronics TS-ME770FS TS-ME770FC Instruction Manual
Thank you for purchasing this Pioneer product. Be sure to read this instruction manual before installing this speaker.
BEFORE YOU BEGIN INSTALLING
Check with your local waterway authority for any regulations the use of accent / speaker lighting on your boat and vessel.
WARNING The marine-grade speakers are capable of reproducing music at extremely loud levels. Caution should be exercised to prevent permanent hearing loss. Additionally, listening music with the audio system at high volume levels could impair your ability to hear a warning signal.
Caution
To prevent damage to your speakers please observe the following caution. Be sure to install at a place having no possible problem with the boat’s and vessel’s safety. Consult your dealer on method of installation. Since this speaker is continuously used being turned on full blast, temperature of the magnetic circuit rises, avoid touching it directly by hand and placing something near it. If it is heated, it may cause a burn, deformation of or damage to peripheral things.
Do not install on submersibles or any boat and vessel likely to be under water at any time. Do not hit to this speaker high-pressure water spray in long time. PIONEER recommends that this speaker be used in conjunction with amplifiers whose continuous (RMS) output is lower than the nominal input power of this speaker. Do not touch the speaker flexible wire 0. Do not bend the terminal ()with force.
Do not pull the tweeter cord © with force. Make sure speaker terminals and/or flexible wires do not come into contact with metal surfaces.
It may cause short circuiting, sparks, electrical failure or fire hazards. Please use a stainless-steel fasteners to ensure a secure installation. When making connections, refer also to the instruction manual of the marine-grade audio unit or amplifier.
FEATURES
- Pioneer ME-series marine speakers are protected from the effects of sun and water exposure, meeting both IPX7 and ASTM D4329 to achieve all-weather reliability
- Mica reinforced IMPP monocoque cone with rubber surround constructed using an advanced in-mold bonding technique for superior water resistance while maintaining high quality, powerful sound
- Symmetrical motor design with high strength suspension optimized to provide stability, linearity and clear, low distortion sound reproduction
- Lightweight polyimide (PI) tweeter diaphragm and uniquely shaped wave guide provides natural and clear vocals with wide dispersion
- Classic, contemporary grille cosmetically integrates seamlessly into marine interior and cabin designs (TS ME770FC)
- Sleek, modern grille design included in both black and white cosmetically integrates seamlessly into marine interior and cabin designs (TS ME770FS)
- Optional RGB color illumination of the woofer cone provides enhanced personalization and cosmetic integration (UD-ME770LED RGB LED light KIT required, sold separately)
SPECIFICATIONS
- Reproduction system: Coaxial two way
- Speaker specifications Woofer: cb 195 mm (7-5/8″ dia.) Tweeter q520 mm (13/16″ dia.)
- Continuous power handling: (RMS) 75 W
- Maximum peak power handling: 250 W
- Sensitivity: 88 dB (1 W / 1 m) 94 dB (1 W / 0.5 m)
- Frequency response: 32 Hz to 23 kHz (-20 dB)
- Nominal impedance: 4 Q
- Cutout diameter: / 159 mm (6-1/4″ dia.)
- Waterproof performance: IPX7
Characteristic
Output Sound Pressure Frequency Characteristic: Input Voltage 2 V
How To Install
Dimensions
Parts Included
-
4 mmx 35 mm X12
-
X12
-
X 2 (TS-ME770FS)
-
X 2 (TS-ME770FS)
-
3 mm X 25 mm
X 6
2 colour grilles are included
How To Replace The Grille
Take tweeter wire out
Take 6 screws out
Take 2 screws out
Do not lose screws
Do not crush the diaphragm
Tighten 2 screws
Tighten 6 screws
| Model | Cutout hole: | Mounting depth: | Height |
|---|---|---|---|
| Ts-ME770FS | 159 (6-1/4 Dia.) | 80 (3-18), 80(3-18) | 27 (1-1/8) |
| Ts-ME770FC | 159 (6-1/4 Dia.) | 80 (3-18), 80(3-18) | 27 (1-1/8) |
How to Use of UD-ME770LED (sold separately)
CAUTION
- Do not connect the LED wires to speaker signal.
- Do not short circuit +12 V wire and R.G.B. wires when it will be connected to a power supply.
How to Use LED Kit
LED kit
To power supply or controller
LED kit
Screw ×3
Fuse 1 A
Use a fuse of 1 A sold separately.
EU models only
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>