ENFORCER SK-919T1-GBWQ Wired Single-Channel RF Transmitter Installation Guide
- June 6, 2024
- ENFORCER
Table of Contents
Wired Single-ChannelRF Transmitter
**SK-919T1-GBWQ (315MHz)*
SK-939T1-GBWQ (433.92MHz)†
Installation Manual**
Specifications
| Model | SK-919T1-GBWQ | SK-939T1-GBWQ |
|---|---|---|
| Type | 1-Channel Wired RF Transmitter | |
| Switch | Two 6″ wires for N.O. |
Wiring
Power| Two 6″ wires for power input
Battery| 3VDC battery (CR-2032. included)
Power
External| 3-13 VDC output regulated adapter
RF Frequency| 315MHz (FCC)| 433.92MHz (CE)
of Buttons| 1
Channels| 1
Possible codes| Over 68 billion (6.8×1010)
Dimensions| 11/4″x23/16″x5/16″ (31.5x55x8 mm)
Dimensions
- Powered by an internal battery or external 3~13 VDC output regulated adapter (not included)
- Frequency 315MHz / 433.92MHz
- Operates up to 500ft (150m)*
- Over 68 billion (6.8×1010 ) possible codes
- LED transmission indicator
- Includes one 3VDC lithium battery (CR-2032)
- Compact size
- Compatible with all SECO-LARM SK-series receivers of the same frequency
- Also available without logo –
SK-919T1-GBWUQ – 315MHz ****
SK-939T1-GBWUQ – 433.92MHz
*Actual range will vary depending on the installation and operating environment
Sample Applications
Make any push-to-exit plate wireless
Convert photo beam sensors with dry
contacts into an entry alert
Wireless equipment/perimeter security
Wireless doorbell/service call button
ENFORCER Wired Single-Channel RF Transmitter
Installation
Power Connection
The wired transmitter can be powered by the factory preinstalled 3VDC lithium
battery (CR-2032) or by an external 3~13VDC output regulated adapter (not
included).
If an external power adapter is preferred, connect the red and black wires of
the wired transmitter to the adapter’s output wires, being careful to ensure
correct polarity. The red wire is connected to the positive and the black wire
to the negative.
NOTES:
- The power input range of the wired transmitter is 3~13VDC and is polarity sensitive. Connecting more than 13VDC or reversing the polarity will burn out the unit and void the warranty.
- Use only “regulated” adapters to power the wired transmitter.
- If using an external power adapter, the factory-installed lithium CR-2032 battery will serve as a backup in case of power interruption (Battery must be removed for external inline power-on switch).
- If connected to an external power-on switch, it is suggested that you remove the battery to disable the built-in button so that it can only be controlled by the power-on switch.
External Switch Connection
The wired transmitter can be controlled by its built-in button (see Fig. 1),
by an external N.O. switch* only (button, contact, or sensor, see Fig. 2), or
by both (Fig. 3). To disable the built-in button, the external switch must be
installed inline to the positive terminal of the power source with the battery
removed.
NOTES:
- Any wires not in use must be insulated to avoid a short-circuit
- Do not let the red wire touch any other wire. Doing so may burn out the transmitter.
*Switch not included
FCC COMPLIANCE STATEMENT (SK-919T1-GBWQ)
FCC ID: K4E919T2GDW
This device complies with part 15 of the FCC rules. operation is subject to
the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Notice : The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any change
to the antenna or the device could result in the device exceeding the RF
exposure requirements and void the user’s authority to operate the device.
California Proposition 65 Warning: These products may contain chemicals
that are known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
WARRANTY : This SECO-LARM product is warranted against defects in
material and workmanship while used in normal service for one (1) year from
the date of sale to the original customer. SECO-LARM’s obligation is limited
to the repair or replacement of any defective part if the unit is returned,
transportation prepaid, to SECO-LARM. This Warranty is void if damage is
caused by or attributed to acts of God, physical or electrical misuse or
abuse, neglect, repair or alteration, improper or abnormal usage, or faulty
installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects
in material and workmanship. The sole obligation of SECO-LARM and the
purchaser’s exclusive remedy shall be limited to the replacement or repair
only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any
special, collateral, incidental, or consequential personal or property damage
of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and
improvement. For that reason, SECO-LARM reserves the right to change
specifications without notice.
SECO-LARM is also not responsible for misprints. All trademarks are the
property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright ©
2021 SECO-LARM U.S.A., Inc.
All rights reserved.
SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: 949-261-2999 |
800-662-0800
Website: www.seco-larm.com
Email: sales@seco-larm.com
PITSW1
Order Part# 762-121%
MI_SK-9x9T1-GBWQ_210119
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>