better bathrooms BeBa-24919 Touch Control LED Mirror User Manual
- June 6, 2024
- Better Bathrooms
Table of Contents
better bathrooms BeBa-24919 Touch Control LED Mirror
CONGRATULATIONS ON YOUR PURCHASE
Our aim at Better Bathrooms is to bring you extraordinary bathroom products, for less.
If you’re after a modern, traditional, or a totally unique style bathroom, we have the fittings and fixtures to bring your ideas to life, so you can fall in love with your space every day.
We hope you’re happy with your new product. But if you experience any problems, we’re always here to help.
- Call our friendly UK call centre on 0330 390 3062 (Lines open 9am-4.30pm Monday to Friday, or 9am-2pm Saturday).
- Send us a message via www.betterbathrooms.com.
PRODUCT OVERVIEW
SAFETY
- This mirror should be installed by a qualified electrician.
- This fitting is only suitable for connection to a 220-240V earthed supply in accordance with current IEE wiring regulations, and should be installed in accordance with local Building Regulations.
- This is for domestic, indoor use only.
- The fitting should be connected to a dedicated lighting circuit which must be protected by a 5-amp fuse (or a 6 amp miniature circuit breaker).
- The electrical connection must be an adequate distance from the rear of the mirror to prevent the risk of shorting with the mirror’s casing.
- Before installing the fitting ensure that the mains supply is switched off, and that the appropriate fuse is removed (or appropriate circuit breaker is switched off) before commencing installation. Ensure that measures are taken to prevent the supply from being inadvertently reconnected.
- If there is a “Minimum Distance” label, please do not allow flammable materials to rest within that distance from the unit.
- This product may contain delicate parts be careful during handling and maintenance to avoid breakage.
- If any modification is made to the fitting it will invalidate the warranty and may render the product unsafe.
- A defective appliance may cause electric shock. Never switch on a defective or damaged appliance. Disconnect the appliance from the mains before seeking assistance.
- This product is IP44 rated, and no part of the installation is allowed to be within bathroom Zones 0 or 1. Installation is permitted within Zone 2.
- This product must be earthed. Before commencing installation, ensure that there are no pipes or wires located behind the wall that may be damaged during drilling.
- Ensure that the hanging location has been decided upon and marked clearly to avoid unwanted damage to the wall due to incorrect positioning.
- Inspect the mirror to ensure there are no signs of damage prior to installation.
- Take care unpacking, do not use a sharp blade to open as this may damage the mirror and void your warranty.
- Once installed a bead of silicon can be applied between the mirror and the wall around the unit. Never seal the bottom of the mirror to the wall, as this may allow water to accumulate behind the mirror.
BATHROOM ZONES
Zone 0: | The interior of the bathtub or shower basin. |
---|---|
Zone 1 | The area around the bathtub or shower basin up to a height of |
2.25m above the floor
Zone 2:| The area stretching to 0.6m outside the bath or shower and
above the bath or shower if over 2.25m
INSTALLATION
IMPORTANT: Before commencing installation, ensure that there are no pipes or wires located behind the wall that you will be drilling into.
- Ensure that the hanging location has been decided upon and marked clearly to avoid unwanted damage in the wall due to incorrect positioning.
- Check there the mirror is not damaged prior to installation.
- Take care unpacking, do not use a sharp blade to open as this may damage the mirror and void your warranty.
At the back of the mirror, there are 2 hanging hooks spaced across the top. To
hang the mirror, two holes are required in the wall. Before drilling, ensure
that no wires or pipes are behind the wall. If unsure, seek professional
advice.
- Measure the distance between the centre of the two hanging points.
- Make a note of the distance and mark their position on the wall. Use a spirit level to ensure that the marks are level.
- Drill the 2 holes into the wall at the position marked using a suitable drill bit.
- Insert the wall plugs into the holes.
- Insert the screws into the wall plugs, ensuring their heads are protruding by approximately 3mm.
- Check to ensure the screws line up correctly and the mirror can be safely hung from them.
- Carefully lower the mirror onto the 2 screws, ensuring that is secure and will not slide.
CONNECTING THE MIRROR
To connect your mirror, it must be first be connected to the mains supply.
IMPORTANT: Installation must only be carried out by a qualified professional or electrician.
At the back of your mirror is a length of 3 core cable which is connected to the mirror. After fitting the fuse spur which will be used to connect the mirror to the mains, identify the EARTH NEUTRAL and LIVE wires in both the spur and the mirror.
When connecting the cables, ensure that no connections are lose, and that proper safety regulations have been followed. Leave enough cable to make moving and hanging the mirror easier.
After connection, the mirror should be hung using the steps 4-5 in the “HANGING THE MIRROR SECTION”.
OPERATION
When the mirror is connected and hung securely onto the wall, turn the mains power back on and the mirror will be ready to use. To operate, use the touch button on the front of the mirror, it is located at the bottom. Touch the button gently to turn on, and press again to switch off.
TECHNICAL SPECIFICATION
Model | BeBa-24919 |
---|---|
LxHxW (cm) | 80x80x3.5 |
Net Weight (Kg) | 6.65 |
Power Cord length (cm) | 68.5 |
Rated Power | 44 W |
IP Rating | IP44 |
Input | 220 V – 240 V 50 Hz |
DISPOSAL
Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centers.
For more information
- visit www.betterbalhrooms.com
- email customerservlcesr@buyitdirect.co.uk
- call 0330 390 3062
- write to Trident Business Park, Neptune Way, Huddersfield, HD21UA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>