MONGOOSE BT200 Rear Red LED Light with Built-in GPS tracker User Manual

June 6, 2024
MONGOOSE

MONGOOSE BT200 Rear Red LED Light with Built-in GPS tracker User Manual
MONGOOSE BT200 Rear Red LED Light with Built-in GPS
tracker

Overview

MONGOOSE BT200 Rear Red LED Light with Built-in GPS
tracker

Included

  • 1 x Rear red LED light with built-in GPS tracker
  • 1 x Fitting bracket
  • 1 x mains/USB charger
  • This manual
  • Free APP download for your mobile phone or tablet – Android or
  • IOS.
    • Free website access on your computer
  • Required;
    • Activated sim card ( Vodafone ONLY! )

IMPORTANT


Record your IMEI number (Shown on the tracker label)


Record your trackers SIM phone number

BT200 GPS TRACKER

Thank you for choosing Mongoose as your GPS tracking provider.
The BT200 is a battery operated GPS tracker for both safety and security.
Apart from tracking GPS satellites, it also contains LBS (land based system) for search and rescue assistance and gives approximate location based on mobile phone cell sites. This can be used if, for some reason, there is no satellite GPS reception. LBS will show which cell tower area the tracker is within – not an actual accurate location.
It contains a rechargeable battery with a standby life of up to 14 days. The mobile APP displays the current battery condition.
The tracker also contains a mounting bracket suitable for attaching a bicycles saddle stem or other tubular frame.

The bracket allows for quick detachment should you wish to use the tracker off the bicycle.

The tracker allowsfree access to a 3rd party mobile APP and onlinePC website.
The APP is a powerful tool and is used for tracker location, historical travel as well as issuing commands that control how the tracker operates.
Location data is stored on the website for a continuing 6 month period. More detailed travel history and reporting functions can be found on the website.

How GPS tracking works

The tracker uses fixed orbit GPS satellites to find its location on the earth. The tracker therefore needs to beagle to ‘see’ the sky in order the receive satellite information. It cannot receive satellite information when inside buildings or in locations where the view of the sky is interrupted.

The tracker requires its own mobile 2G GSM SIM card so it can send GPS location data to the website and the mobile APP. It also allows for text communications.

Locations are automatically uploaded to the website using inexpensive mobile data.

The mobile APP is used to display the information stored on the website.
The APP and the website are also used to control and change tracker settings.
The tracker, APP and website work seamlessly together with virtually no delay in operation.

The trackers SIMcard must have the ability and credit for VOICE, TEXT and DATA.

Vodafone is the only 2G PROVIDER, NO OTHER CARDS WILL WORK.

Due to the nature of this product, a PrePay SIM card is usually sufficient, but ensure ‘auto top-up’ is selected when registering the SIM phone number with the service provider.

Quick guide
  1. Fully charge the battery before using

  2. Insert the 2G GSM SIM cardand turn on outdoors.
    Small LEDsflash whenGSM and GPS signals are located
    The main red LED will light for a short period during boot-up

  3. Configure the tracker with the 5 text messages detailed on page 5

  4. Download the mobile APP and logon to see your tracker.

Battery & charger

Fully charge the battery for about 8 hours or until small red LED goes out.

Subsequent charging should take approximately 4~6 hours depending on battery state.

Please use the 240v to 5v charger supplied.

NOTE: Do not use the USB lead connected to a computer to charge – charging time will be considerably extended.

The mobile APP shows the battery charge on the opening screen.

SIM card installation
  • Open the rubber cover
    SIM card installation

  • Insert the microSIM card
    SIM card installation

  • Close the dust/rain cover
    SIM card installation

SIM card type:- Vodafone is the only 2G PROVIDER, NO OTHER CARDS WILL WORK.
The SIM card must have the ability and credit for VOICE, TEXT and DATA.

Mounting bracket

Usually attached to the saddle stem or other suitable tubular mounting point with the light facing backwards.

The quickly detachable thumb screws can be replaced with more permanent locking nuts (not supplied) if you prefer this method for better security.

The tracker thumb screw allows easy detachment of the tracker itself to make battery recharging more convenient.

Mounting bracket

IMPORTANT: THESE 5 TEXT COMMANDS MUST BE SENT FROM YOUR MOBILE PHONE TO THE TRACKERS PHONE NUMBER FOR THIS PRODUCT TO OPERATE CORRECTLY.

  1. Pair your mobile phone to the tracker
    The tracker needs to know your mobile phone number so it can communicate with you.
    Send this text message from your phone to the trackers SIM phone number;
    admin123456 XXXXXXXXXX
    space here
    123456 is the password – XXXXXXXXX is your mobile number Reply: admin okay

  2. Set the time zone (for accurate reporting times)
    Send this text message timezone123456 13 (13hours ahead of GMTfor NZ daylight saving)
    space here Reply: Time ok

  3. Set how often to upload location to APP & website (10~300sec’s)
    Send this text messageupload123456 20 (upload locationto website every 30 sec’s)
    space here Reply: Upload ok

  4. Set the APN Access Point Name –your SIM cards data connection
    apn123456 warehouse (The Warehouse SIM)
    or apn123456 internet (2 Degrees SIM)
    space here Reply: APN ok

  5. START GPRS DATA LOCATION REPORTING
    gprs123456 Reply: GPRS ok
    To cancel data uploading, send:-nogprs123456 NoGPRS ok

IP ADDRESS OF RECEIVING COMPUTER

Openand login intothe mobile APP. If there is a message at the top of the screen ‘not enabled’, this means that the website has not received any tracker data. One reason may be the IP address needs to be re-set.(Other reasons can be the SIM card not activated, wrong APN, or no data allowance on SIM)
Send this text message to the tracker: adminip123456 47.88.85.196 7700
You should get a reply: adminip okay

DOWNLOAD THE MOBILE APP

Android or IOSAPP :- TKSTAR GPS


Google Play Store

Apple Store

LOGON TO THE APP

If you own just one GPS tracker, select ‘Log in   by IMEI’
Owners of multiple trackers select ‘Log in by   username’

Login Interface

Login Interface

Multiple trackers

Please contact Mongoose for a username and password to be allocated

The mobile APP gives you full control of the trackers features as well as showing real time location and historical travel. The APP can be used on smartphones and tablets.
Please explore the features.

APP ICONS

App Icons

  • ‘Real time tracking’ –shows current / last reported position
  • ‘Historical route’ –shows the locations/routefor a particular day
  • ‘Geofence’ –allows you to set defined boundaries
  • ‘Issue command’ –sets tracker parameters & commands
  • ‘Device info’ – Details about the tracker, SIM number etc
  • ‘Device message’ – record of texts sent from device
  • ‘Alarm setting’ -define which alerts are required
HOW TO TRACK WITH THE MOBILE APP

Open the app and logon.
Complete all details to ‘Device Info’ – some features will not operate if not completed
Click on ‘real time’ to show current location.
Click on ‘historical route’ to show where the tracker has been.

  • APP menu
    App menu

  • Real time location
    Real Time Location Tracker

  • Historical travel replay
    Historical Travel Replay Tracker

LOG ONTO THE WEBSITE

Goto:- www.mytkstar.net

The international website may open in Chinese. Select your chosen language by clicking on the corresponding flag.
The next time you go to the website, it will default to your chosen language.

Login onto website Interface

This website is operated by a third party andis free to use.
No fees are payable apart from your trackers SIM charges.

GPS Navigation system

Log onto to the website as you would for the mobile APP.
The website stores all the location data which the APP accesses.
Travel is more detailed compared to the mobile APP.History replay is shown above.
Travel reports can be saved and printed.

MULTIPLE TRACKERS –USERNAME LOGON

If you have more than one tracker, call Mongoose to request an account. You can choose your own username and password that allows you to monitor all devices with just one logon.

TEXT (SMS) LOCATION REQUEST

If not using the APP, send thistextfrom any smart mobile phone to the trackers mobile number:-

G123456#

  • Google link: tap the link, it opens opens the phones map to show location.
  • v:A = GPS signal ok. v:V = no GPS signal
  • 2013-08-30 20:54:15: the last reported date and time of GPS information.
  • Spd:000km/h: the speed of tracker.
  • Bat:6 state of battery back-up charge
  • ID:4102000759: Unique IMEI code of device
  • S19G04;plmn:46001 GSM operator data
    Lac:9516, cellid:23596 LBS data
LED’s – WHAT THEY MEAN
  • YellowLED —Mobile GSM signal state
    • Unlit: off or in discretemode
    • Lit solid: searching
    • Flashing once every 3 sec’s: connected to network
  • Blue LED –GPS signal state
    • Unlit: off or in discrete mode
    • Lit solid: searching
    • Flashing once every 3 sec’s: receiving GPS
  • Red LED – battery
    • Lit solid: charging
    • Off: fully charged or not connected to charger
SOS NUMBERS

Apart from your paired mobile phone, you can add 2 other SOS numbers that also receive alerts.
The numbers can be set within the APP under ‘issue command’

CONTROLLING THE TRACKER

The tracker can be controlled via the mobile APP or by text messages from your phone.

APP: Use ‘issue command’ in the mobile APP.
The APP gives you the choice of controlling by data (GPRS) or by SMS (text).
The following are explanations of commands that can be sent by text or by the APP.

TIME-ZONE

GPS tracking time is based on GMT (Greenwich Mean Time). To get accurate reporting times, a text command to the tracker must be sent to set the correct time zone.

timezone123456 12 –when no daylight saving
timezone123456 13 –with daylight saving

FREQUENCY OF LOCATION REPORTING Range:- 10~300 seconds
To maximize the battery life, thetracker only reports when moving. It should be set to report its location at reasonable time intervalsto give an accurate map plot of travel. 20 to 30 seconds is typical.
When stationary for more than 10 minutes, it enters sleep mode – turns off GPS reception and stops reportinglocations to preserve battery life.Mobile receptionand alert functions are still on.

Send this text message upload123456 20 (upload every 20 seconds when moving)

GPRS

This stands for ‘Global Packet Radio System’. Commonly called ‘data’.
It is the method of sending computer data over the mobile phone network.
It should not be confused with the letters GPS.

RED LED LIGHT –how to control

The bright red rear light can be controlled from within the APP or by these text messages;

  • led123456 on The light will flash until it is turned off
  • led123456 off Turns the flashing light off
  • led123456 shock The LED light will start to flash when the tracker receives a shock or vibration. It automatically turns off if no shock or vibration is detected for 5 seconds.

The LED light will naturally shorten battery life, so check the APP for battery condition and recharge as necessary.

GEO-FENCE ANTI-THEFT ALERT

A geo-fence is an invisible boundary around a fixed location.
This boundary can have a minimum radius of 100m to a maximum of 5000m. Geo- fences can be added and deleted.
If the tracker moves out of or into a geo-fenced area, it will send a text alert to the authorised numbers confirming it is either ‘IN” or ‘OUT’ of the geo-fenced area.
You can set multiple geo-fence areas.

NOTE: In normal use this can become an unnecessary text, together with associated text cost, and will shorten battery life. Only use the feature when required.
To stop it sending texts, either delete the geo-fence or turn off in ‘alarm settings’ on the mobile APP.

SHOCK ANTI-THEFT ALERT

When the tracker has beenstationaryfor 5 minutesand it then receives a heavy shock, it will send atext alert.

You canactivate shock alert by APP command or text message: shock123456

You can cancel shock alert by APP command or text message: noshock123456

MOVE ANTI-THEFT ALERT

Once the tracker has remained stationary for more than 5minutes, you can set a move alert.
move123456 reply: move ok

If the tracker moves more than 500m (factory setting), it will send a text alert to the paired mobile phones.

To cancel this mode, send
nomove123456 reply: nomove ok

SPEED ALERT

You can set a speed limit for the tracker and receive a text alert if this speed is exceeded every 5 minutes.

speed123456 60 reply: speed ok

To cancel this alert, send nospeed123456 reply: nospeed ok

Do not set speeds lower than 50km/has GPS willbe inaccurate at low speeds.

LOW BATTERY ALERT

When battery voltage is too low, it will send a text alert
Battery condition is shown on the mobile APP.
Alert can be programmed on or off. See chart at rear of this manual.

MONITOR MODE – Covert Listening

This mode allows you dial in and listen to what is happening around your tracker.
In monitor mode,
Send this text: monitor123456
Now make a phone call to the trackers SIM number, allow it to ring and it will answer. You can now listen – you cannot talk. Hang up when finished.
GPS tracking is not possible in monitor mode.
Once you have finished with this feature, switch it back to tracking mode,

TRACKER MODE

Send this text: tracker123456
Switches the tracker from monitor mode to tracking mode

LBS

LBS stands for ‘Land based System’. It is a basic location method based on the closest mobile cell tower. It is mainly used for search and rescue when a GPS satellite fix cannot be obtained. It will not provide an accurate location, just which search area it is within.
When using the APP or website to see current or historical locations, uncheck ‘LBS’ to prevent spurious locations from appearing – usually signified by straight lines.

TEXT COMMAND CHART

Instruction

| Text to send to trackers SIM #|

Reply

---|---|---
Cell phone pairing (master user #1)| admin123456 xxxxxxxxx
(xxxxxxxx = your mobile phone number)| admin ok
Cancel pairing| noadmin123456 xxxxxxxxx| noadmin ok
SOS – Tamper alert| sos123456 xxxxxxxxx mobile no’

sossms123456 Text alert

soscall123456 Call alert To cancel, insert ‘no’ in front of text

eg; nososcall123456

| ok
Set time zone| timezone123456 13
(EG: NZ Daylight saving – 13 hours ahead of GMT)| time ok
Set how often to upload location to APP & website| upload123456 20
(range 10~300 sec’s)| upload ok
Start sending location data to

website

| ****

gprs123456

| ****

gprs ok

Stop sending location data to website| nogprs123456| nogprs ok
Tracker mode| tracker123456| tracker ok
Monitor mode| monitor123456| monitor ok
Move alert| move123456

nomove123456

| move ok

nomove ok

Speeding alert| speed123456 105

nospeed123456

| speed ok

nospeed ok

Shock alert| shock123456

noshock123456

| shock ok

noshock ok

Request location by text reply| g123456| Tap blue to see on your phones map
Set mobile APN| apn123456 xxxxxxx
(xxxxxxx = APN name)| APN ok
Set IP address| adminip123456 47.88.85.196| adminip ok
Change password| password123456 XXXXXX
Must be numbers – 6 digit| password ok
Check setting| Param1 or Param2| Shows settings
Language|

  • LAG1 (English)
  • LAG2 (Chinese)

|

  • Switched to English
  • Switched to Chinese

Check IP address| (S42,1234)| Tracker status, IMEI, IP address etc
Turn red LED on| led123456 on| LED on ok
Turn red LED off| led123456 off| LED off ok
Auto LED turn on by shock| led123456 shock| LED shock ok
Turn shock off| led123456 off| LED off ok
Low battery alert|

  • LOWBATSMS123456 on
  • LOWBATSMS123456 off

| lowbatsms ok
Parameters| check123456| sends all tracker parameters
Reset| format or begin123456| Re-sets all settings to default

Caution:

This product contains a Li-ion battery which has harmful chemicals.
Do not dismantle, drop, bump, puncture or treat it violently.
Do not get wet – tracker is water resistant, not water proof.
Never incinerate.
Never submerge.
Do not leave the battery discharged as this will affect its recharge ability.

This GPS tracking device uses the 2G GSM mobile network for sending data and texts.
Mongoose is not responsible or liable if the mobile network becomes unavailable for any reason.
The purchase of this product provides free access to an international mobile APP and website. These are operated by a 3rd party and Mongoose has no control over the design or operation. Mongoose accepts no liability or responsibility if the APP or website become unavailable or access terms change.

  1. Head Light
  2. SIM Card Slot
  3. Indicator Light
  4. USB Port
  5. SOS Button

Overview

INDICATOR LIGHT STATUS MEANING
Yellow light -Solid No GPRS signal
Yellow light -Flash GPRS connection
Blue light -Solid No GPS signal
Blue light -Flash GPS connection

Note: GSM SIM CARD INSTALLTION GUIDE: ONLY GSM SIM cardworks in this model.

Specification

GSM module 2G GSM Quad Band 850/900/1800/1900Mhz
Network 2G GSM/GPRS/LBS
SIM card Micro SIM
GPS sensitivity -159dBm
GPS chipset UBLOX
GPS Position Accuracy 5m (outdoors)
Time Accuracy Synchronized to GPS time & GMT
Cold start 45~80 sec
Hot start 1 sec., average
Warm start 35 sec., average
Battery Re-chargeable Li-ion – 3.7v 1800mAh
Charger 110v~220v input 5v output
Battery standby Up to 14 days. Operating life is subject to usage &

environmental effects. Using flashing LED light will shorten life considerably
Operating temperature| -20°C to +55° C
Dimensions| 40 x 85 x 28mm 80g
Humidity| 5% to 95% Non-condensing
Dust / Water resistance| IP67
USB input| For charging – use charger supplied

Support

Mongoose New Zealand Limited
www.mongoose.co.nz
Email: sales@mongoose.co.nz
Phone: (09) 443 3128

MONGOOSE Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals