STAMINA InLine 55-1406 Back Stretch Bench Pro Owner’s Manual

STAMINA InLine 55-1406 Back Stretch Bench Pro

SAFETY INSTRUCTIONS

WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
WARNING: Consult your physician before starting this or any exercise program. This is especially important if you are over the age of 35, have never exercised before, are pregnant, or suffer from any health problem. This product is for home use only. Do not use in institutional or commercial applications. Failure to follow all warnings and instructions could result in serious injury or death.
WARNING: To reduce the risk of serious injury, read the following Safety Instructions before using the inLINE® Back Stretch Bench Pro.

1. Save these instructions and ensure that other exercisers read this manual prior to using the inLINE® Back Stretch Bench Pro for the first time.
2. Read all warnings and cautions posted on the inLINE® Back Stretch Bench Pro.
3. The inLINE® Back Stretch Bench Pro should only be used after a thorough review of the Owner’s Manual. Make sure that it is properly assembled and tightened before use.
4. We recommend that two people be available for assembly of this product.
5. Keep children away from the inLINE® Back Stretch Bench Pro. Do not allow children to use or play on the inLINE® Back Stretch Bench Pro. Keep children and pets away from the inLINE® Back Stretch Bench Pro when it is in use.
6. It is recommended that you place this product on an equipment mat.
7. Set up and operate the inLINE® Back Stretch Bench Pro on a solid level surface. Do not position the inLINE® Back Stretch Bench Pro on loose rugs or uneven surfaces.
8. Make sure that adequate space is available for access to and around the inLINE® Back Stretch Bench Pro.
9. Before using, inspect the inLINE® Back Stretch Bench Pro for worn or loose components, and securely tighten or replace any worn or loose components prior to use.
10. Consult your physician before using this product. If you feel faint, dizzy, or experience pain during use, stop immediately and consult with your physician.
11. Choose the intensity that fits your strength and flexibility level. Know your body’s limits and use this product within them. Use common sense when using this product.
12. Do not wear loose or dangling clothing while using the inLINE® Back Stretch Bench Pro.
13. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross training shoes that fit well, provide foot support, and feature non-skid rubber soles.
14. Be careful to maintain your balance while using, mounting, dismounting, or assembling the inLINE® Back Stretch Bench Pro, loss of balance may result in a fall and bodily injury.
15. The inLINE® Back Stretch Bench Pro should not be used by persons weighing over 250 pounds.
16. The inLINE® Back Stretch Bench Pro should be used by only one person at a time.
17. The inLINE® Back Stretch Bench Pro is for consumer use only. It is not for use in public or semipublic facilities.

BEFORE YOU BEGIN

We take great pride in this quality product and hope it will provide many hours of quality exercise to make you feel better, look better, and enjoy life to its fullest.
It’s a proven fact that a regular exercise program can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise. The inLINE® Back Stretch Bench Pro provides a convenient and simple method to begin your journey of getting your body in shape and achieving a happier and healthier lifestyle.
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Locate the serial decal on the product and write the serial number on the cover of the manual in the space provided. See the next page for an image of the serial decal. Model number and serial number are required when calling for assistance.
Read this manual carefully before using the inLINE® Back Stretch Bench Pro.
Providing you with a quality product is Stamina’s top priority. However, sometimes there could be a missing or incorrectly sized part. If you have any questions or problems with the parts included with your inLINE® Back Stretch Bench Pro, please do not return the product. Contact us FIRST!
If a part is missing or defective, please contact Customer Care for assistance. Call us toll free at 1-800-375-7520 (in the U.S.) or live chat on staminaproducts.com. Our Customer Care Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.
Be sure to have the name and model number of the product available when you contact us.

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY:

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.

NOTICE: The length of all bolts and screws, except those with flat heads, is measured from below the head to the end of the bolt or screw. Flat head bolts and screws are measured from the top of the head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items. Some hardware may be already attached to the part.

Part Number and Description

• 33 – Bolt, Button Head (M6 x 1 x 13mm) – Quantity 4
• 34 – Bolt, Button Head (M8 x 1.25 x 22mm) – Quantity 4

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part, please go to staminaproducts.com under the Customer Care section and order the part needed, e-mail us at customer.care@staminaproducts.com, or call us toll free at 1-800-375-7520 (in the U.S.). Our Customer Care Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.
Some product parts are fit tested at the factory to ensure proper fit and alignment. Marks in the paint may be noticeable, but are not an indication of damage.

• STEP 1
  Slide the PILLOW(39) onto the CUSHION(12) and secure in position with the elastic band. Attach the CUSHION(12) to the MAIN FRAME(1) with BUTTON HEAD BOLTS(M6x1x13mm)(33).

• STEP 2
  Push the BUTTON PIN(9) in and insert the ARMPIT PAD SUPPORT(7) into the SWING ARM(6). Slide an ARMPIT PAD(8) on the ARMPIT PAD SUPPORT(7). Repeat on other side.
  NOTE: There are three adjustment holes in the bottom of the SWING ARM(6) which allow the ARMPIT PAD SUPPORTS(7) to be attached in three different positions. Start with the center position and adjust if necessary.
  

• STEP 3
  Insert the HEIGHT ADJUSTMENT BEAM(3) into the EXTENDING TUBE(2). Lock the HEIGHT ADJUSTMENT BEAM(3) in position by inserting the pin of the ADJUSTMENT KNOB(23) into one of the adjustment holes in the HEIGHT ADJUSTMENT BEAM(3) and tightening the ADJUSTMENT KNOB(23).

• STEP 4
  Insert the PAD TUBE(5) through the hole in the HEIGHT ADJUSTMENT BEAM(3) and secure with BUTTON HEAD BOLT(M8x1.25x22mm)(34). Slide the FOAM PADS(24) on both ends of the PAD TUBE(5).

• STEP 5
  Refer to detail view A, push in the BUTTON PIN(9) and insert the ADJUSTABLE INSTEP FRAME(4) into the HEIGHT ADJUSTMENT BEAM(3). Slide the FOAM PADS(24) on both ends of the ADJUSTABLE INSTEP FRAME(4).
  NOTE: There are four adjustment holes in the HEIGHT ADJUSTMENT BEAM(3) which allow the ADJUSTABLE INSTEP FRAME(4) to be attached in four different positions. Find the position which is most comfortable for holding your ankles while performing the back stretching exercise.
  

STORAGE

1. To store the inLINE® Back Stretch Bench Pro, simply keep it in a clean dry place.
2. Adjust the HEIGHT ADJUSTMENT BEAM(3) and MAIN FRAME(1) to the shortest position. The inLINE® Back Stretch Bench Pro is approximately 56 inches long x 18.5 inches wide x 14 inches tall. These dimensions will vary. Please measure your inLINE® Back Stretch Bench Pro if exact dimensions are needed.
3. To move the inLINE® Back Stretch Bench Pro, lift by the CUSHION(12) on one end and the HEIGHT ADJUSTMENT BEAM(3) at the other end. Use caution as the SWING ARMS(6) may move and cause a pinching hazard.

MAINTENANCE

The safety and integrity designed into the inLINE® Back Stretch Bench Pro can only be maintained when the inLINE® Back Stretch Bench Pro is regularly examined for damage and wear. Special attention should be given to the following:

1. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts. Tighten loose nuts and bolts.
2. Verify that the CAUTION LABEL(40) is in place and easy to read. Call Stamina Products immediately at 1-800-375-7520 for a replacement CAUTION LABEL(40) if it is missing or damaged.
3. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
4. Worn or damaged components must be replaced immediately or the inLINE® Back Stretch Bench Pro removed from service until repair is made.
5. Only Stamina Products supplied components should be used to maintain/repair the inLINE® Back Stretch Bench Pro.
6. Keep your inLINE® Back Stretch Bench Pro clean by wiping it off with an absorbent cloth after use.

OPERATIONAL INSTRUCTIONS

STRETCH SYSTEM

The inLINE® Back Stretch Bench Pro stretches the back with its one way rack and pinion engineering. Lie on the inLINE® Back Stretch Bench Pro with the ARMPIT PADS(8) under your armpits, and the FOAM PADS(24) holding your ankles. Pull the LEVER(13) back and forth as many times as needed until you feel a gentle stretch. Stop pulling at the desired position and stay at the stretched position for a few minutes. Push the LEVER(13) firmly toward your feet to release the stretch.

NOTE: Prior to releasing the stretch please remove your arms from the ARMPIT PAD SUPPORTS(7). Once the ARMPIT PAD SUPPORTS(7) are no longer under your arms push the LEVER(13) firmly toward your feet to release the stretch.

USING THE inLINE® Back Stretch Bench Pro

To use the inLINE® Back Stretch Bench Pro, proper height adjustment is important. Use the following procedure to set the height adjustment for a revitalizing stretch.

1. Refer to illustration A. Push the LEVER(13) toward the FOAM PADS(24) at your feet and pull the EXTENDING TUBE(2) in to its shortest position.
2. Lie on the inLINE® Back Stretch Bench Pro with the ARMPIT PADS(8) under and supporting your armpits. If the ARMPIT PADS(8) do not rest comfortably under your armpits, adjust the ARMPIT PAD SUPPORTS(7) by pushing in the BUTTON PIN(9) and sliding them in or out of the SWING ARMS(6). Straighten your body and legs to determine if a height adjustment needs to be made.
3. To make a height adjustment, loosen and pull the ADJUSTMENT KNOB(23) and slide the HEIGHT ADJUSTMENT BEAM(3) to adjust. Lock the HEIGHT ADJUSTMENT BEAM(3) in desired position by inserting the pin of the ADJUSTMENT KNOB(23) into one of the adjustment holes in the HEIGHT ADJUSTMENT BEAM(3). Tighten the ADJUSTMENT KNOB(23) to lock the HEIGHT ADJUSTMENT BEAM(3) securely.
4. Sit up on the CUSHION(12). Adjust the ADJUSTABLE INSTEP FRAME(4) by pushing in the BUTTON PIN(9) and sliding it up, then place your ankles between the FOAM PADS(24). Push the ADJUSTABLE INSTEP FRAME(4) down to secure your feet. Place the ADJUSTABLE INSTEP FRAME(4) at the position which is most comfortable for holding your ankles. Lie down with the ARMPIT PADS(8) under and supporting your armpits, refer to illustration B.
5. To stretch, pull the LEVER(13) back and forth as many times as needed to reach the proper stretch. Stop pulling at the desired stretch position and stay at the stretch position for few minutes. To release, push the LEVER(13) firmly toward your feet.

ARMPIT PAD ADJUSTMENT

To accommodate different sizes of users, the ARMPIT PAD SUPPORTS(7) can be adjusted to one of three positions. Refer to the Bottom View illustration above. There are three adjustment holes in the bottom of the SWING ARM(6). Start with the center position and adjust if necessary. To adjust, push the BUTTON PIN(9) in and slide the ARMPIT PAD SUPPORTS(7) to the position that is comfortable. Make sure that the BUTTON PIN(9) is snapped into the proper adjustment hole before use.

LIMITED WARRANTY

WARRANTY

Stamina Products, Inc. (“Stamina”) warrants to the original purchaser that this product will be free from defects in materials and workmanship that arise under normal use, service, proper assembly and proper operation in accordance with product warnings/instructions for a period of 90 days on the parts and one year on the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE, ALTERATION OF ANY KIND OR TO ANY DEFECT OR CHANGE CAUSED BY IMPROPER ASSEMBLY, REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS NOT PROVIDED BY STAMINA. Commercial use includes use of product in athletic clubs, health clubs, spas, gyms, and all other public or semipublic facilities whether or not the product’s use is in furtherance of a profit making enterprise, and all other use which is not for personal purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase and a brief description of the defect along with your receipt to Stamina Products, Inc. 2040 N Alliance Ave, Springfield, Missouri, USA, MO 65803, or email us at customer.care@staminaproducts.com, or call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the product or part to us for free repair or replacement at our option.
NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY (INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. These warranties are not transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY. If any claim is made under this limited warranty or any implied warranty, Stamina reserves the right to require the product to be returned for inspection, at the purchaser’s expense, to Stamina’s premises in Springfield, Missouri. Return of the enclosed warranty registration card is not required for warranty coverage, but is merely a way of establishing the date and place of purchase.
Stamina SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED WARRANTY.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS WARRANTY. NO ORAL OR WRITTEN INFORMATION GIVEN BY STAMINA, ITS AGENTS OR EMPLOYEES, SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. This warranty gives you specific legal rights, and you may also have other legal rights which vary from state to state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
The laws in some states affect the disclaimer or limitation of implied warranties and consequential and incidental damages. If any such law is found applicable, the foregoing disclaimers and limitations of and on implied warranties and consequential and incidental damages shall be deemed to be modified to the extent necessary to comply with applicable law.

PRODUCT PARTS DRAWING

PARTS LIST

PART#

| PART NAME|

QTY

---|---|---

1

| Main Frame| 1
2| Extending Tube|

1

3

| Height Adjustment Beam| 1
4| Adjustable Instep Frame|

1

5

| Pad Tube| 1
6| Swing Arm|

2

7

| Armpit Pad Support| 2
8| Armpit Pad|

2

9

| Button Pin| 3
10| Square Bushing|

4

11

| Bushing| 4
12| Cushion|

1

13

| Lever| 1
14| Ball end|

1

15

| Gear| 1
16| Shaft|

1

17

| Twist Spring| 1
18| Claw|

1

19

| C Ring (8mm)| 1
20| Claw Stopper|

1

21

| Pressing Spring| 1
22| Gear Rack|

1

23

| Adjustment Knob| 1
24| Foam Pad|

4

25

| Wheel| 2
26| Round Plug (19mm)|

4

27

| Round Plug (25mm)| 4
28| Square Plug (30 x 30mm)|

2

29

| Endcap (38mm)| 4
30| Shoulder Bolt, Button Head (M6 x 1 x 18mm)|

1

31

| Carriage Bolt (M8 x 1.25 x 35mm)| 2
32| Carriage Bolt (M8 x 1.25 x 52mm)|

2

33

| Bolt, Button Head (M6 x 1 x 13mm)| 4
34| Bolt, Button Head (M8 x 1.25 x 22mm)|

1

35

| Serial Decal| 1
36| Bolt, Flat Head (M6 x 1 x 13mm)|

2

37

| Screw, Round Head (M3.4 x 8mm)| 1
38| Nylock Nut (M8 x 1.25)|

6

39

| Pillow| 1
40| Caution Label|

1

41

| Allen Wrench (4mm)| 1
42| Allen Wrench (6mm)|

1

43

| Manual| 1

Email: customer.care@staminaproducts.com
Website: www.staminaproducts.com
Tel: 1 800-375-7520
Fax: 417-889-8064
STAMINA PRODUCTS, INC.
ATTN: Customer Care
2040 N Alliance Ave, Springfield, MO 65803

References

• Customer Care - Exercise Equipment | Stamina Products
• Customer Care - Exercise Equipment | Stamina Products
• Customer Care - Exercise Equipment | Stamina Products
• Quality Home Fitness & Exercise Equipment | Stamina Products
• P65Warnings.ca.gov
• Quality Home Fitness & Exercise Equipment | Stamina Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>