ENFORCER MVE-AHMPM-41NQ 4K HDMI Extender over IP User Manual

: June 6, 2024
: ENFORCER

Table of Contents

Features
Introduction
Parts List
Specifications
Overview
Installation
Sample Applications — One-to-One
Sample Applications — One-to-Many, Switch/Router
WARRANTY
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ENFORCER MVE-AHMPM-41NQ 4K HDMI Extender over IP User Manual

Features

Extends HDMI over one Cat5e/6 cable or IP network
Supports One-to-One, and One-to-Many applications
Power adapters and IR hardware included
IR Support (20kHz~60kHz)
HDCP Compliant
Receiver (MVE-AHMPM-41NRQ) also available separately

HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Introduction

The MVE-AHMPM-41NQ 4K HDMI Extender over IP extends the range of HDMI signals by using an active transmitter and receiver to send video and audio over a single Cat5e/6 cable. The 4K HDMI Extender over IP supports IR signals using the included IR transmitter and receiver, allowing remote control use from one end of an installation to control a device such as a media player or DVD player at the opposite end of the installation. The MVE-AHMPM-41NQ supports One-to-One, and One-to-Many installations, allowing the connection of multiple units for extended range.

Parts List

1x Transmitter
1x Receiver
1x IR Transmitter
1x IR Receiver
2x Power adapters
1x Manual

Specifications

Model| Transmitter

MVE-AHMPM-41NTQ

| Receiver

MVE-AHMPM-41NRQ

---|---|---
Maximum video resolution| 4K@30Hz
Deep color| 24-bit
Video formats supported| DTV/HDTV: 480i, 480p,576i,576p,720p,1080i, 1080p, 4K@30Hz

Range – 4K

| Cat5| 262ft (80m)

Cat5e

|

328ft (100m)

Cat6|

393ft (120m)

IP addressing

| Static
IR frequency|

20kHz~60kHz

Operating voltage

| 5VDC
Power supply|

2A@5VDC

Power consumption

| 6W| 4W
Operating temperature|

32°~140° F (0°~60° C)

Dimensions

| 47/16″x15/16″x311/16″ (112x23x94 mm)
Weight|

5.9-oz (170g)

Overview

Input/output are reversed on the transmitter

Installation

Determine the location where the 4K HDMI Extender over IP units will be installed as well as how much Cat5e/6 cable will be necessary.
Connect the transmitter to the HDMI output of the source device.
Connect the transmitter and receiver:
- If connecting One-to-One, connect one end of the Cat5e/6 cable to the transmitter and the other end directly to the receiver.
- If installing with a switch or router, connect one end of the Cat5e/6 cable to the transmitter and the other end to a switch or router. Then, with a second Cat5e/6 cable connect the receiver to the other end of the switch or router.
Connect the receiver to the HDMI input of the display or other device.
Connect one 5VDC adapter to the transmitter and the other to the receiver.
If remote control is desired:
- Install the IR transmitter extension to the IR OUT port of the transmitter, pointing the IR transmitter at the IR sensor of the device to be controlled.
- Install the IR receiver extension to the IR IN port of the receiver, pointing the IR receiver in a direct line of sight to where the remote control will be.
- Point the remote control at the IR receiver when in use.
Switch on the HDMI source and display to verify that the system is functioning properly. It may take up to a minute to sync up the video stream.

Sample Applications — One-to-One

Cable Legend:

HDMI
Power
IR
Cat5e/6

Sample Applications — One-to-Many, Switch/Router

Cable Legend:

HDMI
Power
IR
Cat5e/6

California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO- LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

WARRANTY

This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2021 SECO-LARM U.S.A., Inc. All rights reserved.