ENFORCER EV-Y2251-A2WQ 4-in-1 HD TVI, CVI, AHD, Analog Turret Cameras User Manual
- June 6, 2024
- ENFORCER
Table of Contents
ENFORCER EV-Y2251-A2WQ 4-in-1 HD TVI, CVI, AHD, Analog Turret Cameras User Manual
Features:
- ICR Module
- D-WDR (Digital Wide Dynamic Range)
- Joystick OSD control
- Heavy-duty vandal-resistant design
- Rugged, weatherproof (IP66) construction
- Split-glass design eliminates IR reflection
- Cables concealed in bracket to prevent tampering
Specifications:
Parts List:
Overview:
OSD Controller Settings:
To set format via the OSD controller, move the controller in the direction of
the desired setting, hold for 5 seconds, and release when the camera restarts.
See chart below.
NOTE : Do not press joystick in when setting different modes.
Before Starting:
- Use the camera within the given temperature and voltage limits.
- Do not point the camera at the sun. Heat could damage the camera, even when not in use.
- Do not subject the camera to strong vibrations.
- Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
Installation:
-
Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted.
-
Loosen the outer case ring and remove the case from the base.
NOTE: The camera ball is NOT attached to the case or the base. It sits loose inside the case. Therefore, be very careful when removing the case from the base. Do not drop the camera ball. -
Mount the base to the wall using the three included mounting screws. If the wall is made of dry wall, brick, or similar material, it may be necessary to use the included screw anchors.
-
Run the camera’s BNC and power connectors through the camera base, and connect to the video and power wires that were run through the wall.
-
Put the case over the camera ball and onto the base.
-
Holding the case loosely on the base, turn the camera ball to the desired direction. Use a small screwdriver to adjust the zoom and focus of the camera ball if needed, via the holes marked “ZOOM” and “FOCUS” on the top of the camera ball (EV-Y2501-AMWQ, EV-Y2251-AMWQ, and EV-Y2501-AMGQ only).
NOTE: Before securing installation, make sure to check both the day and night images. Adjust the camera ball in a way so that there are no objects blocking the camera’s view. -
Use the OSD controller joystick to adjust camera settings (see the separate OSD manual).
-
Once the ball is pointing in the desired direction, tighten the outer case ring to secure the camera in its position.
-
Do a final test of the video camera and monitor.
Troubleshooting:
California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open the case of this device, as there are no user-serviceable components inside. Do not cut any wires as the warranty will be voided.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO- LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no
change to the antenna or the device is permitted. Any change to the antenna or
the device could result in the device exceeding the RF exposure requirements
and void user’s authority to operate the device.
WARRANTY : This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
NOTICE : The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., Inc. All rights reserved.
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-
larm.com
Phone: 949-261-2999 |
800-662-0800 Email: sales@seco-
larm.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>