GEWA Electronic Cymbals Owner’s Manual

Owner´s Manual
CP14
CP14-AC
CP18
CP18-AC
Electronic Cymbals

CP14 | CP14-AC | CP18 | CP18AC
Electronic Cymbals

Models| CP14 | CP14-AC | CP18 | CP18AC
---|---
Document| Owner´s Manual
Version| 1.0
Release Date| 2020-10-09

Please read this Owner´s Manual carefully before operating the device and take note of the safety information! Keep this document available for immediate reference.
Download the complete user´s manual on gewamusic.com:
https://int.gewamusic.com/downloads

https://int.gewamusic.com/downloads
www.gewaelectronics.com

SAFETY INFORMATION

Failure to observe the following safety directives may result in fire, electric shock, injury, device damage, or damage of other objects or property. Read the following safety instructions completely before operating this product.
Further risks are possible; therefore, the following list does not claim to be complete.
About the symbols
WARNING
Calls your attention to risks that can result in serious injuries or death.
CAUTION
Calls your attention to risks that can result in minor injuries and/or device damage.
REGULATION
Indicates a required action. The action which must be carried out is stated more precisely by the white design contained.
BAN
The symbol alerts the user to items that must never be carried out (are forbidden). The prohibited action is stated more precisely by the design contained within the circle.
WARNING
Indicates a hazard that could result in serious injury or death.
Do not disassemble or modify
Do not disassemble or modify this product unless this manual provides specific instructions.
Do not repair or replace parts by yourself
Do not attempt to repair the unit or replace parts within it (except when this manual provides specific instructions directing you to do so).
Refer all servicing to your retailer, GEWA service partner.
Do not use or store in the following locations

• Locations of high temperature (in direct sunlight. near heating equipment)
• Moist or humid locations (near a bath or shower, or a wet floor)
• Locations exposed to steam or smoke
• Locations subject to salt damage
• Locations subject to water or rain
• Expressively dusty or sandy environment
• Locations subject to high levels of vibration
• An environment with poor ventilation

CAUTION
Indicates a hazard that could result in injury or property damage.
Use only the specified stand
Install the unit only on the hi-hat stand which satis­fies the specifications described on p.9. Remove only the specified screws during the installation.
Evaluate safety issues before using stands
Even if you observe the cautions given in the own­er’s manual, certain types of handling may allow this product to fall from the stand or cause the stand to overturn. Please be mindful of any safety issues before using this product.
Do not place in unstable locations
Never place the unit on unstable stands. Such stands encourage malfunction and add potential risk for children by facing over.
Manage cables for safety
Try to prevent cords and cables from becoming entangled. Also. all cords and cables should be placed so they are out of the reach of children.
Route all power cords and cables in such a way as to prevent them from getting entangled
Injury could result if someone were to trip on a ca­’ be and cause the unit to fall or topple.
** Don’t allow foreign objects or liquids to enter the unit; never place containers with liquid on the unit
Do not place containers containing liquid on this product. Never allow foreign objects (e.g., flam­mable objects, coins, wires) or liquids to enter this product. Doing so may cause short circuits, faulty operation, or other malfunctions.
Do not drop or expose to strong impact
Otherwise, you risk causing damage or malfunction.
Be cautious to protect children from injury
Always make sure that an adult is on hand to pro­vide supervision and guidance when using the unit places where children are present, or when a child will be using the unit.
Avoid climbing on top of the unit, or placing heavy objects on it
Otherwise, you risk injury as the result of the unit toppling over or dropping down.
Take care not to pinch your fingers in the movable parts
Be careful not to allow your fingers or hands to be caught between the top and bottom hi-hat. Adult supervision is recommended whenever small chil­dren use the unit.
Disconnect all cords/cables before moving the unit
Damage or malfunction may result if you fail to disconnect all cables before moving the unit.
Keep small items out of the reach of children
To prevent accidental ingestion of the parts listed below, always keep them out of the reach of small children.
Removable Parts:
Clutch or clamp screws and nuts, clutch bumper, cymbal seat, felt washers, spinlock, and cable plugs.
Additional information about the use
Placement**

• This unit may interfere with radio and television Do not use this unit in the vicinity of such receivers.
• When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours until the condensation has com­pletely evaporated.
• Whenever any liquid has been spilled on the sur­face of this unit, be sure to promptly wipe it away using a soft, dry
• Spurs included with stands and pads might scratch the floor. Use a mat or similar, adequate object to protect the floors from damage.
• Make sure that children are not exposed to risks of injury caused by improper placement or setup of

Maintenance

• Never use benzene, thinners, alcohol, or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
• Remove stick marks and dust by treating the top surface of the cymbal with a sponge lightly soaked in silicone oil. Silicone oil protects the top sutruce um! teslotes U rleSi I and even look.
• For everyday, cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterward, be sure to wipe the unit thoroughly with a soft, dry

Additional Precautions

• Use a reasonable amount of care when using the unit’s jacks and connectors. Rough handling can lead to malfunctions.
• When disconnecting all cables, grasp the con­nector itself – never pull on the cable. This way you will avoid causing cable breakage and short
• This instrument is designed to minimize the extra­neous sounds produced when it’s played. How­ever, impact noise still can be transmitted through floors and walls to a greater degree than ex­pected, take care not to allow these sounds to become a nuisance to others nearby.
• Continuous playing may cause discoloration of the pad, but this will not affect the pad’s function.

DISPOSAL AND RECYCLING

EU Countries

**Devices labeled with this symbol fall under the scope of the European Waste Electrical and Electronic Equipment Directive (WEEE) under which owners are obliged to dispose of such devices separately from domestic waste. Manufacturers and EU member states on the other hand are obliged to transpose the directive into federal law and provide separate collection systems to ensure effective protection of human health and the environment. In case this product needs to be disposed of, take it to your local community waste management service (e.g. disposal companies, re-cycling centers) or to the dealer where the product was purchased.
USA**
CA Prop 65
This product contains chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm, including lead.

PACKAGE CONTENTS

The original packaging contains the following items. Please check carefully the completeness of the purchased product:

ASSEMBLY INSTRUCTIONS

1. Screw cymbal seat (D) on an 8 mm cymbal arm (F).
2. Place the cymbal (C) on the cymbal seat (D), followed by the spinlock (B).
3. Orient the spinlock (B) in the cymbal mold as shown in Figure 3.
4. With the spinlock attached, orient the whole cymbal with the “G“ facing in playing position.
5. Secure the cymbal seat (D) by fastening screw (E) as shown in Figure 1.
6. Screw felt and wing nut (A) onto the cymbal arm.

CONNECTIONS & TRIGGER SETTINGS

Standard (Trigger Type = Dual)
The standard connection only utilizes one cable for all component sensors (Bow, Bell, and Edge). The required Trigger Type (Dual) is set by default in the factory Trig­ger Banks and Setups provided for GEWA Cymbals.

1. Connect the stereo cable to the cymbal, using the jack closest to the middle hole (Z).

2. Connect the other plug of cable to one of the following Trigger Inputs of your console:
   Ride I Crash 1 I Crash 2 I Aux 1-4 I (Hi-Hat)

3. In your Drum Console make sure that the cor­rect Trigger Bank is loaded at the corresponding input channel. *
   Default Trigger Banks:
   CP14: GEWA Crash 14inch
   CP18: GEWA Ride 18inch
   

*For more information about loading trigger banks consult the owner’s manual of your GE-WA Console.
Option: 3Way triggering (Trigger Type = 3Way)
3Way triggering moves the Bell signal to its own connection, resulting in a 2-cable setup. With this method, it is possible to use individual velocity curves for Edge and Bell signals. Signals for Bow and Edge remain in connection (1), whereas the bell is connected to the Console via the outer jack of the cymbal (2). See the table on the right-hand side for all combinations of trigger inputs available for 3Way triggering.
With this setup, load the matching “3W” Trigger Bank version at the input channel to which the Bow Component of your Cymbal is connected.
Cymbal Component

| Bow/Edge| | Bell
---|---|---|---
Trigger Inputs| Ride| +| Aux 1
Aux 1| +| Aux 2
Aux 2| +| Aux 3
Aux 3| +| Aux 4
Trigger Banks:| CP14:| GEWA Crash 14inch 3W
---|---|---
CP14:| GEWA Ride 18inch 3W

Note
Other Manufacturers (Modules)
Although GEWA cymbals are manufactured to meet industry standards of analog trigger sys­tems, GEWA does not guarantee flawless functioning with equipment of other manufacturers. The operation of this product with 3rd party equipment is at your own risk. If you still decide to operate this product with 3rd party drum modules, please take first note of the following hints:

• Check first whether your drum module supports the trigger types (Sensors) built into GEWA pads.
• Check whether the manufacturer of your module offers a trigger bank for the GEWA pad you want to connect.
• Consult the owner’s manual of your drum module for Information about trigger setups, accessible parameters, and customization of 3rd party

PLAYING TECHNIQUES

Cymbals
Tip Stroke (Bow)

Strike the bow region with the tip of the stick within the highlighted area. This will trigger the bow sound.
Edge Stroke

Bell Stroke

Bells on acoustic cymbals produce musical sounds using either the shoulder or the tip of the stick. Utilize both techniques to trigger the bell sound.
Cymbal Choke

After performing an Edge Stroke, subsequently, apply pressure to the edge sensor using the fingers. This will prevent the edge sound from sustaining any longer. Regarding Hi- ats this technique is only practical for longer sounding, open sounds.
With pressure applied to the edge, striking the cymbal will result in a short, staccato edge sound.

COMPATIBLE STANDS

Compatible stands for GEWA E-Cymbal seats

The following measurements describe the minimum requirements for a cymbal stand to fit GEWA E-Cymbal Seats, providing enough play for free cymbal movement. Note that the min/max measurements suppose an overall height of wing nut and felt of 33 mm (1 ¾”).

| | | Measure in [mm]| Measure in Inch [“]
---|---|---|---|---
A| Thread diameter| M8| 8 mm|
B| Thread length| min| 38,1mm| 1 ½”
C| Length non-threaded rod| min| 38,1mm| 1 ½”
D| Diameter non threaded part| max| 8,5 mm|

TECHNICAL DATA

CP14 Electronic cymbal (Included with drum set configurations)

Bell Trigger Output (optional for 3Way trig­gering)
Dimensions| 52 (H) x 355 (Ø) mm
2 (H) x 14 (Ø) inches
Weight| 850g / 1 lb 14 oz
Accessories included| Owner’s manual (this document)

CP 14-AC Electronic cymbal with accessories

Bell Trigger Output (optional for 3Way triggering)
Dimensions| 52 (H) x 355 (Ø) mm
2 (H) x 14 (Ø) inches
Weight| 1080 g/ 2lbs 6 oz
Accessories included| Universal e-cymbal seat, 8mm wing nut with felt, spinlock, 6,35 mm (1/4″) TRS stereo cable, owner’s manual (this document)

Cr ID-AC Electronic Cymbal With accessories

Bell Trigger Output (optional for 3Way triggering)

Dimensions| 55 (H) x 458 (Ø) mm
2 1/64 (H) x 18 (Ø) inches
Weight| 16409/ 3lbs 10 oz
Accessories in- chided| Universal e-cymbal seat, 8mm wing nut with felt, spinlock, 6,35 mm (1/4″) TRS stereo cable, owner’s manual (this document)

For reasons of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. The present specifications describe the version of the product at the time this document was issued. For the latest specifications please refer to gewamusic.com.

GEWA music GmbH
Oelsnitzer Straße 58
08626 Adorf
GERMANY
www.gewamusic.com
Manufacturer
GEWA music GmbH
Oelsnitzer Straße 58
08626 Adorf
GERMANY

References

• Gewamusic - English
• GEWA Drum Workstation G9
• Gewamusic - English
• Gewa Česká republika - GEWA music Tschechien
• Gewa España
• Gewa France - GEWA music France
• Gewa International - GEWA music International
• Gewa Italia - GEWA music Italia
• Gewa Polska - GEWA music Polen
• Gewa Portugal - GEWA Portugal
• Gewa Deutschland - we engineer music

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>