innr Wireless RF Mode User Guide
- June 6, 2024
- innr
Table of Contents
Connection to the bridge:
To connect the lamp to the bridge, follow the instructions in the related mobile app.
Factory-reset:
Switch the lamp OFF and ON six times (6x) with intervals of 0,5-1 seconds. The lamp will blink to indicate it is factory-reset. It can then be connected to a bridge again.
CAUTIONS and OPERATING INSTRUCTIONS:
- Not for use in totally enclosed or recessed fixtures.
- Not suitable for use with regular dimmers.
- Risk of electric shock – do not use when directly exposed to water.
- This device is not intended for use with emergency exit fixtures or emergency lights.
- Only install in operating environments between 0°F – 100°F / -20°C – +40°C.
- Before replacing, turn off the power and let the device cool down to avoid burning.
- The device is for indoor use only.
- Do not immerse in water or use the device in wet locations, e.g. bathrooms or outdoors.
- For cleaning, use a damp cloth, never a strong cleaning agent.
- Do not clean the device when it is on and connected to the power supply.
- This device is not a toy, designed to be played with by children.
- Do not place this device on hot surfaces.
- For safety reasons, do not open this device, which will also void the warranty.
- Use the device only in a socket rated for this device.
- Dispose of this device in accordance with disposal laws in your area.
FCC Certification:
FCC ID: 2AB2Q8ZA806ST04G
FCC Supplier’s Declaration of Conformity
AE 280 C
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference. and (2) this device must accept any interference received.
including interference that may cause undesired operation.
Supplier’s name: Opened Box Returns LLC
Supplier’s address (USA): 1790 Swarthmore Ave.. Unit 6. Lakewood NJ 08701 USA
Supplier’s phone number and/or internet contact information:
usaservice@innr.com
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment,
Note: This device has been tested and found to comply with the limits for a
Class B digital device. pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.This device generates. uses and can radiate radio
frequency energy and. if not installed and used in accordance with the
instructions. may cause harmful interference to radio communications. However.
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on. the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment, This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and any part of your body.
IC Certification:
IC: 10256A-8ZA806STQ4G
This device contains license-exempt transmitters)/receiver(s) that comply with
Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference. including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and any part of
your body.
This Class B digital apparatus complies with Canadian ICES-005. This digital
apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications
LIMITED WARRANTY:
Inner warrants that this device will be free from defects in material and workmanship and will operate for 2 years based on up to 3 hours average usage per day/7 days per week. when used as directed. If this device does not conform to the warranty. Innr will send you, at its election. a replacement device or refund your original purchase price upon receipt of the returned device. register receipt and proof of purchase. Please send an email to service@innr.com to find out how to return the device. This limited warranty does not cover devices subject to accident. neglect. abuse. misuse or acts of God. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages. so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights. and you may also have other rights which vary from state to state and province to province.
Wireless specification:
Wireless RF mode frequency band: 2400~2483.5 MHz
Wireless communications protocol: IEEE 802.15.4
Operating channels: channels 11 – 26
Environmental specification:
Temperature (operation): -20°C – 40°C
Temperature (storage): -25°C – 60°C
Relative humidity: 5-95 % non-condensing
Standby power: < 0.2W per lamp
© Innr Lighting B.V. 2019
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>