beamZ SkyNight LED Galaxy Effect Light User Guide
- June 6, 2024
- beamZ
Table of Contents
BAMZ
MADE
EAZY
153.210 V1
SKYNIGHT
QUICK START GUIDE
SAFETY INSTRUCTIONS
Before carrying out any operations with the unit, carefully read this
instruction manual and keep it with care for future reference. It contains
important information about the installation, usage, and maintenance of the
unit.
WARNING!
- Unpack and check carefully that there is no transportation damage before using the unit
- Please read these instructions carefully and follow the instructions.
- Observe all safety warnings. Never remove safety warnings or other information from the equipment.
- Be sure that no ventilation slots are blocked; otherwise, the unit will overheat.
WARNING!
Before connecting the equipment to the power outlet, first, verify that the
mains voltage and frequency match the values specified on the equipment. If
the equipment has a voltage selection switch, connect the equipment to the
power outlet only if the equipment values and the mains power values match. If
the included power cord or the power adapter does not fit in your wall outlet,
contact your electrician.
-
After connecting the unit, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
-
Make sure that the power cord is never crimped or damaged. Check the unit and the power cord from time to time.
-
Always disconnect power from the mains, when the unit is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
-
Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.
-
Do not switch the unit on and off in short intervals.
-
Do not connect the unit to a dimmer pack.
-
Install the unit in a well-ventilated place.
-
Never place any material over the lens.
-
Never let the sunlight lights directly to the front lens, even when the unit is not working.
-
Always allow free air space of at least 50 cm around the unit for ventilation.
-
Make sure that the area below the installation place is blocked when rigging, derigging, or servicing the unit.
-
For mounting height >100 cm, always fix the unit with an appropriate safety rope. Fix the safety-rope at the correct fixation points only.
The safety-rope must never be fixed at the transport handles! -
Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light may trigger epileptic seizures in photosensitive persons or persons with epilepsy.
-
This unit is not designed for permanent operation. Consistent operation breaks will ensure that the unit will serve you for a long time without defects.
WARNING!
If the power cord of the unit is equipped with earthing contact, then it must
be connected to an outlet with a protective ground.
Never deactivate the protective ground of a power cord.
- Make sure that the unit is not exposed to extreme heat, moisture, or dust.
- Clean the unit using a dry cloth.
- Do not touch the unit bare-handed during its operation (housing becomes very hot). Allow the unit to cool for at least 5 minutes before handling.
- This unit is designed exclusively for indoor use, do not use this equipment in the immediate vicinity of fluid (does not apply to special outdoor equipment – in this case, observe the special instructions noted below). Do not expose this unit to flammable materials, fluids or gases.
- If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.
- Never attempt to bypass the thermostatic switch or fuses.
- Do not dismantle or modify the unit.
- For replacement use fuses/bulbs of the same type and rating only.
- Repairs, servicing, and electric connections must be carried out by a qualified technician.
- The ambient temperature must always be between -5° C and +45° C.
- If this unit is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
- Plastic bags must be kept out of reach of children.
- The unit must be installed out of the reach of children. Never leave the unit running unattended.
This symbol on the product or on its packaging indicates that this product
shall not be treated as household waste. Instead, it shall be handed over to
the applicable collection point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product. The
recycling of materials will help to conserve natural resources. For more
detailed information about recycling of this product, please contact your
local Civic Office, your household waste disposal service, or the shop where
you purchased the product.
UNPACKING INSTRUCTION
CAUTION!
Immediately upon receiving the product, carefully unpack the carton, check the
contents to ensure that all parts are present, and have been received in good
condition. Notify the shipper immediately and retain the packing material for
inspection if any parts appear damaged from shipping or the package itself
shows signs of mishandling. Save the package and all packing materials. In the
event that the product must be returned to the factory, it is important that
the product be returned to the original factory box and packed.
If the unit has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation
water might damage your unit. Leave the unit switched off until it has reached
room temperature.
FUNCTION DESCRIPTION
-
USB input. Note that this projector can automatically recognize and play music while USB memory is inserted. USB must contain some songs.
-
a. Adjust the brightness of the ocean waves at 3 levels.
b. When power is on, LED light and laser light will stay on, short press control LED light switch, long press control laser light switch. -
DC input: 5V/2A.
-
Short press to play the previous track, long press to decrease volume.
-
Short press to play the next track, long press to decrease volume.
-
Short press to play or pause music, long press to turn BT on or off.
-
Press the button to switch between USB to BT (Connect BT and USB stick at the same time, then USB stick has music for priority).
-
Power on/off.
REMOTE CONTROL
- LED ocean wave light ON/OFF.
- Laser light ON/OFF.
- Press
"R", red light ON. Press again, red light OFF (at basic of light on at the first time) - Press “G”, green light ON. Press again, green light OFF (at basic of light on at the first time).
- Press
"B", blue light ON. Press again, blue light OFF (at basic of light on at the first time). - Press
"W ", white light ON. Press again, white light OFF (at basic of light on at the first time). - Volume up.
- Volume down.
- Previous track
- Next track
- Sound to light control: Connect with BT or USB memory playing music, press’IMICII icon, ocean wave, and starlight ill respond to the sound of the music.
- Control ocean wave moving speed up (Pause-Slow-Medium-Fast).
- Control ocean wave moving speed down (Fast-Medium-Slow-Pause).
- Long press (3 seconds) to stop timer function.
- Press “
FADE 1” ocean waves move circularly in R-G-B-W single color mode double-color mode and laser light changed to graduation mode.
(the same features as power On).
- Press “
FADE 2” ocean waves move circularly in RB-RG-RW-BG-BW-GW double-color mode and laser light changed to program mode. - Long press (3 seconds) control timing function for 1 hour. When LED, laser light flashes and emit “bleep” sound once time as prompting. One hour later, it’ll automatically switch off.
- Control LED ocean wave light brightness(In order of 70%-40%-40%-70%-100%).
- Press “
LASER light” for a stay on or enter into program mode. - Long press (3 seconds) control timing function for 2 hours. When LED, laser light flash and emit “bleep” sound 2 times as prompting. Two hours later, it’ll automatically switch off.
- Music Switch On/Off.
DOWNLOAD OUR FULL MANUAL IN MANY LANGUAGES UISIT »» WWW.BEAMZLIGHTING.COM
YOUR FUTURE
YOUR SKILLS
YOUR PLATFORM
YOUR PARTY
YOUR EVENT
is a leading developer of lighting products, including intelligent OMX
moving heads, wireless battery operated OMX effects, static washes, sound-
activated club effects,
strobes & blacklights, LED lighting, fog and special effects machines, lasers,
and indoor and outdoor architectural lighting, as well as lighting controllers
and protective bags.
BEAMZLIGHTING.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>