eufy T1305 Lumi Dual Bright Night Light User Manual

eufy T1305 Lumi Dual Bright Night Light User Manual

Important Safety Instructions

Read and follow all the safety instructions:

• This device is for indoor use only
• This device should not be exposed to dripping or splashing water.
• This device is powered by three AAA batteries (not included). Do not attempt to recharge them when using non-rechargeable batteries.
• This device uses a non-replaceable light source. When the light source reaches the end of its life cycle, the device should be replaced.
• Do not install near any heat sources
• Do not place any sources of danger on this device (e.g. liquid filled objects, lighted candles).
• Do not mix different types of batteries together, e.g. lithium-ion (Li-ion) and nickel-metal hydride (NiMH) batteries.
• Do not mix new and used batteries.
• Do not use metal objects to connect the terminals of the battery.
• An exhausted battery should be disposed of according to local environmental regulations.

Introduction

Thank you for purchasing Lumi Dual-Bright Night Light (hereafter called “Lumi”). Lumi uses light and motion sensing technology to temporarily illuminate dark spaces with a soft light.

At a Glance

1. Motion sensor
2. Wall plugs x2
3. Screws x2

Installing the Batteries

1. Slide down to remove the mounting bracket on the back of your Lumi.

2. Insert three AAA batteries. Make sure the positive and negative ends are facing the correct polarity direction as marked in the battery compartment.

Installing Your Lumi

After installing the batteries, there are two ways to install your Lumi. When choosing a suitable location for your Lumi, remember that:

• It should be installed in a dark area.
• Do not install Lumi in a location that can interfere with your work or rest.
• Do not install Lumi in a location that directly faces an infrared beam.
• The motion sensor is designed to cover an arc of approximately 120 degrees horizontally and to detect motion up to 3 meters/10 feet away;
• The effective distance and range are subject to the ambient temperature.
• Make sure the area in front of the motion sensor is obstruction-free.

Option A: Installing Lumi with the adhesive mounting bracket:

1. Remove the protective film on the back of the bracket.

2. Stick the bracket onto the wall. Make sure the arrow on the bracket is pointing up.

3. Align the holes on the back of Lumi with the pins on the bracket; slide down to mount Lumi

Select the type of surface you will adhere the mounting  bracket to carefully. Removing the mounting bracket may cause damage to the surface if removed

Option B Installing Lumi with the supplied screws:

1. Measure a distance of 1.97in (50mm) between two points for the wall plugs. Use a pen to mark the drill points.

2. Use a drill bit to drill two 0.9in (23mm) deep holes and fully insert the wall plugs into the holes.

3. Align the mounting bracket with the wall plugs and hold against the wall. Insert the screws through the fixing holes and screw firmly into the wall plugs. Make sure the arrow on the mounting bracket is pointing up when installing.

4. Align the mounting holes on the back of Lumi with the pins on the mounting bracket; slide down to mount Lumi.

Using Your Lumi

Troubleshooting

Specifications

Specifications are subject to change without notice

Notice

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/ TV technician for help.

The following importer is the responsible party (for FCC matters only) Company Name POWER MOBILE LIFE, LLC
Address: 400108th Ave NE Ste 400, Bellevue, WA 98004-5541
Tel ephone:1-2 06-383-82 4 7

Declaration of Conformity

Hereby, Anker Innovations Limited declares that the product type T1305 is in compliance with Directives 2014/35/EU & 2014/30/EU
The full text of the EU declaration of conformity is available at the following internet address:https://www.eufylife.com/

Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong

Customer Service

For FAQs and more information, please visit: www.eufylife.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>