73E-11215 RunCam Thumb Pro Camera Instruction Manual

October 27, 2023
THUMB

73E-11215 RunCam Thumb Pro Camera
Instruction Manual73E-11215 RunCam Thumb Pro
Camera

Please read this manual carefully before use and keep it in a safe place

Function indication

73E-11215 RunCam Thumb Pro Camera - Figure 1

  1. Detachable lens protection cover
  2. Button (power/shutter button)
  3. Indicator light(Red/Green)
  4. MicroUSB
  5. 1.25mm 4P

Power supply connection and flight controller connection

73E-11215 RunCam Thumb Pro Camera - Figure 2

Camera basic operations

Power on/off| Automatically turn on when powered on, the red light is always on Cut the power or long press the button to power off
---|---
Start/Stop recording| Click the shutter button to start recording, the red light flashes slowly / Click the shutter button again to stop recording, the red light is always on
Mode switch| Double-click the shutter button quickly to switch between the recording mode (the red light is always on) and the parameter settings mode (the green light is always on)
Parameter settings mode| Scan the QR code in the Runcam APP to configure
Remote control mode| Thumb Pro Connect ThumbPro to flight controller for operations
SD card error| Red light keeps flashing fast

Attention: SD card error includes card full, slow card speed, card damage and etc.

Micro SD Card

U3 card is recommended (4K@30FPS/2.7K@60FPS/1080P@120FPS requires U3 or above)
Supports up to 128G microSD card73E-11215 RunCam Thumb Pro Camera - Figure
3

Note: Be careful when handling the microSD card, please avoid contact with liquids, dust and debris.
As a precaution, turn off the camera before inserting or removing a microSD card. Please refer to the microSD card manufacturer’s instructions for use within an acceptable  temperature range.

Computer Connection

Connect the computer via Micro USB, it will be recognized as a U disk.73E-11215 RunCam Thumb Pro Camera - Figure 4

Note: If it cannot be recognized after connecting to the computer, please confirm that there is a microSD card inserted; if the microSD card cannot be read normally, please  try to replace the USB cable or the computer USB interface.

Firmware Update

To ensure optimal performance of the camera, please use the latest firmware version.
Check the link below to update for reference:
https://www.runcam.com/download/ThumbPro
Firmware upgrade status (Red and green lights flashing fast; when the upgrade is completed, the camera automatically shuts down.)

Android and IOS APP
Search“RunCam”on Google play and Apple Store, or download on our website http://www.runcam.com/download

Technical Support
Please visit: https://support.runcam.com

Video Bitrate and Codec

| Video Quality| Codec
---|---|---
Resolution| High| Medium| Low
4K@30fps| 60Mbps| 50Mbps| 40Mbps| H 264
2.7K@60fps| 60Mbps| 50Mbps| 40Mbps
1440P@60fps| 40Mbps| 30Mbps| 20Mbps
1080P@120fps| 60Mbps| 50Mbps| 40Mbps
1080P@60fps| 45Mbps| 30Mbps| 22Mbps|

Flight Controller UART Control

Preparation

  • Firmware: BetaFlight Firmware (3.2.0),CleanFlight Firmware(2.1.0) , KISS Firmware (1.3-RC30) or INAV Firmware (1.7.3).

  • Any available UART interface on the Flight Controller
    1. Connect the Runcam Thumb PRO with the UART interface of the Flight Controller
    2. Make the Flight Controller recognize the Runcam Thumb PRO For example, we connect the Runcam Thumb PRO to the UART 5 interface on the Flight Controller: connect the Flight Controller to the computer, then open the configurator software of the Flight Controller. (Open up the configurator that matches the firmware you  are running, Betaflight Configurator for Betaflight, Cleanflight Configurator for Cleanflight). In the Peripherals column of the line UART 5 (on the Ports tab), select Camera (RunCam Protocol) and click Save And Reboot.
    73E-11215 RunCam Thumb Pro Camera - Figure 53. Instructions of the functions of the camera and assigning transmitter channels to them In the Flight Controller Configurator, navigate to the Modes tab. There are  new CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes

  • CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to move to the next menu item.

  • CAMERA CHANGE MODE: Switch between the recording mode and the QR code setting mode.
    Assign any available channel to the function you need, for example:

  • Assign the AUX2 to the CAMERA POWER, range 1900-2100

  • Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100
    73E-11215 RunCam Thumb Pro Camera - Figure 64. Assign the channel to the switch of the controller
    Please choose your Model on the controller, then access to the MIXER interface and assign the channel to the switch of the controller. Take opentx 2.2.0 for example,  assign the channels CH5, CH6 and CH7 to SA, SB and SD respectively
    73E-11215 RunCam Thumb Pro Camera - Figure 75. Test
    Power the Flight Controller and the Runcam Thumb PRO

  • Set the SA to the bottom, the camera starts/stops the video

  • Set the SD to the bottom, the camera switches among the two modes: video and OSD setting mode

Specifications

Mode Runcam Thumb Pro
Resolution 4K@30fps \2.7K@60fps \1440P@60fps \ 1080P@120fps \1080P@60fps
Video Format MP4
Gyro Bulit-in
Communication Interface Micro USB
Micro SD Card Capacity 256G Max
USB Power Input/ Terminal Power Supply DC 5.0V
Remote Control Uart
Power Consumption 500mA@5V Max
Dimension 54mm25.5mm21mm
Net Weight 16g

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals