summer Everywhere Extra Wide Walk Thru Safety Gate User Manual

Everywhere™ Extra Wide
Walk Thru Safety Gate
USER MANUAL

Please read the following instructions carefully.
Keep this instruction manual and save it for future reference.
For technical support, contact us at 1-401-671-6551 or www.summerinfant.com/contact
Tools required: Phillips-head screwdriver, measuring tape (not included), and wrench (included).
For use with children from 6 – 24 months.
Keep small parts away from children.
Adult assembly required.
Fits openings from 28.75″ – 39.75″ wide.

WARNING
Children have died or been seriously injured when gates are not securely installed.

• ALWAYS install and use gate as directed using all required parts.

• Install according to manufacturer’s instructions.

• Stop using when a child can climb over or dislodge the gate.

• Use only with the locking/latching mechanism securely engaged.

• To prevent falls, never use at top of stairs without wall mounting cups and door stopper.

• You MUST install wall cups to keep the gate in place.
  Without wall cups, children can push out and escape.

• NEVER use a gate to keep the child away from the pool.

• NEVER leave the child unattended.

• ALWAYS close and lock the gate behind you.

• This product will not necessarily prevent all accidents. Proper adult supervision is required at all times.

• Do not use if any components are missing or damaged.

• Adult assembly required. Exercise care when unpacking and assembling products.

CAUTION: KEEP SMALL PARTS OUT OF THE CHILD’S REACH.

components:

NOTE : Gate will appear as though the door is off-center when taken out of the package until you mount it into the doorframe and tighten the bolts according to the instructions.

A. Gate Door
B. 4” extension
C. 4” extension
D. Screws (4)
E. Tension Bolts with Tension Nuts (4)| F. Wall Cups (4)
G. Adhesive Mounting Pads (4)
H. Wrench
I. Wall Anchors (4)
---|---

gate configurations (choose which best fits your scenario)

Measure the width of the opening where you intend to install the gate. Refer to the following illustrations to determine the correct installation configuration. Baseboard molding may change which configuration is appropriate.

Note : This instruction book illustrates the installation of gate configuration D.
If choosing gate configuration A, skip ahead to step 2.
Otherwise, follow step 1 using the appropriate extension frames that best fit your scenario.

Important: Gate includes a doorstop that prevents the gate from swinging open in one direction. When installing the gate at the top of the stairs, be sure that the doorstop is used so the door cannot open over the stairs.

installation:

1. 
   • If choosing gate configuration A, skip this step.
   • If choosing gate configuration B or C, add the desired extension frame to either side of the gate frame.
   Connect the extension frames to the gate frame by inserting extension pins into the holes.

2. Slide tension bolts into upper and lower holes on both sides of extension frames (or into the gate frame if no extensions are being used).

3.  A. Stand the gate in the center of the opening. Make sure the bottom of the gate is completely flush to the floor.
   B. Slide tension bolts out until they contact the door frame or wall on both sides. IMPORTANT
   Check distances A & B. The distance between the gate and the wall should never exceed 2.75 in.

4. Use the tension nuts to tighten both of the bottom tension bolts.

5.  Use the tension nuts to tighten both of the top tension bolts.

STOP! wall cup installation:

WARNING
You MUST install wall cups to keep gate in place. Without wall cups, children can push out and escape.

1. With a pencil, trace the entire outline of each tension bolt directly onto the wall. IMPORTANT
   At the top of the landing, position the gate a minimum of 3-6 inches (8-15cm) away from the top step.

2. Loosen the lower and upper tension nuts and remove the gate.

3.  Place a wall cup over the center of each circular outline on the wall.

4. NOTE: Skip this step if: – mounting directly into wood,
   Drill a 7/32” pilot hole into each of the 4 center marks.

5. Remove backing from one side of each adhesive mounting pad

6. Align the wall cups so the center hole is placed directly over the wall anchor. Stitched wall cups to the wall.

7. Screw wall cups into the wall. Note Screws are Only required for top of stair use.

8. **IMPORTANT**
   NEVER open the gate door over the stairs.
   Repeat “installation” steps on page 5. The 4 tension bolts will rest within each wall cup.

9. Tighten all 4 tension nuts with the provided wrench.

Gate stopper

****Note: This gate includes a gate stopper which prevents the gate door from swinging open in one direction when used at the top of the stairs.
When mounting this product at the top of the stairs, locate the door stopper that is on the opposite side of the stairs.

Testing the installation

1. Close the gate. Make sure the upper and lower latches lock securely.
2. Push the gate and frame to check stability.

Operation

to unlock gate:

First, slide the locking tab back to release.
Second, open the door.

Troubleshooting

If the gate does not close properly:

1. Gate is not properly aligned in the door frame.
   Solution: To adjust the gate’s alignment, loosen all four tension bolts and reposition the gate so that it matches the “correct” image. Re-tighten tension nuts.

2. The pressure of tension bolts needs adjusting.
   Solution: Loosen or tighten the upper tension nuts.
   Ensure the upper latch handle always remains below the release button. Ensure the upper latch handle engages securely when the gate swings closed and that it releases properly when the release button is pressed.

maintenance:

1. Regularly check tension bolts to make sure the gate is securely in place.
2. Do not use the gate if any components are damaged or missing.
3. Surface-clean with a damp cloth or sponge using mild detergent and warm water.

Summer Infant stands behind all of its products. If you are not completely satisfied or have any questions, please contact our Consumer Relations team at 401-671-6551 or www.summerinfant.com/contact

Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
401-671-6551
© 2020 Summer Infant, Inc.
Colors and styles may vary.
MADE IN CHINA.
D0000000852 1/21

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>