Airspan AirSpot 1310 CPE-CBSD Device User Guide

June 6, 2024
Airspan

Airspan-AirSpot-1310-CPE-CBSD-Device-logo

Airspan AirSpot 1310 CPE-CBSD Device

General

Getting Started Guide for Airs pan CPE-CBSD AirSpot 1310.

Instructions

Note: This guide is intended for the customer technicians when installing the device. 2.1 Entering the webGUI with Administrator Credentials

Entering the webGUI with Administrator Credentials

  • Enter the SIM card into the device (when device is still powered off)
  • Connect a laptop/PC Ethernet LAN card to the CPE-CBSD
  • Power on the device (using PoE)
  • Open Google Chrome on the laptop/PC, and type http:/1192.168.0.1 to access the webGUI.Airspan-AirSpot-1310-CPE-CBSD-Device-1
  • Enter the username: superadmin Enter the password: admin (Note: these are the administrator credentials for the technician)

Setting APN #1 Name

  • Go to Setting ➔ Network ➔ APN Management
  • Verify the “APN Number” shows #1
  • Verify the “Status” is checked to “Enabled”.
  • Enter the APN #1 Name according to the network
  • Verify the “Default Gateway” is checked to “Enabled”
  • Check the TR069 checkbox (in case customer has TR-69 server in its network)
  • Press the Submit Button

Important Note: APN #1 is the Management APN communicating over internet with the CBRS SAS and NTP Server.
Important Note: Correct UTC timing of the CPE-CBSD device is mandatory for correct communication with CBRS SAS. CPE-CBSD device needs to receive as part of LTE ATTACH process the correct UTC time as part of S1-NAS EMM message (customer 4G EPC needs to provide this correctly). Airspan-AirSpot-1310-CPE-
CBSD-Device-2

Setting APN #2 Name (typically used in customer networks)
Important Note: If customer network is designed to operate with APN #1 only, then APN #2 is not configured in the CPE­CBSD. Skip this section and continue to the next section.

  • Typically in customer networks there are 2 APNs: APN #1 for Device Management and APN #2 for end user data.
  • Go to Setting ➔ Network ➔ APN Management
  • Select the “APN Number” to #2
  • Check the “Status” to “Enabled”.
  • Enter the APN #2 Name according to the network
  • Verify the “Default Gateway” is NOT checked
  •  Verify the TR069 is NOT checked
  • Verify the SNMP is NOT checked
  • Press the Submit ButtonAirspan-AirSpot-1310-CPE-CBSD-Device-3

Entering CBRS SAS URL and User-ID

  • Go to Setting ➔ System ➔ CBSD
  • Verify the “Certificate Information” exists with Validity until 2030

Important Note: the CPE-CBSD comes from factory with a built-in certificate valid for operation with any commercial SAS. If the “Certificate Information” is empty, the device is malfunctioning and needs to be returned to Airspan for repair.

  • Enter in “Registration Parameters” the following:
    • “User ID” according to the commercial User ID received when establishing the contract with SAS
    • “SAS URL” according to commercial SAS URL. Do NOT enter the https:// as part of the URL. Note: Sometimes SAS declare their URL ending with /v1 .2. Do NOT enter the /v1 .2 as part of the URL.
  • Press the “Submit” buttonAirspan-AirSpot-1310-CPE-CBSD-Device-4
  • Go to Settings ➔ System ➔ Maintenance
  • Press the “Regular Reset” button
  • The device will reboot automatically

Important Note: this CPE-CBSD device is certified under FCC Part 96 rules. The CPE-CBSD will NOT pass user data traffic until reaching AUTHORIZED state from CBRS Commercial SAS.
Important Note: this CPE-CBSD device is certified under FCC Part 96 rules. This device is a Category B CBSD which must be professionally installed. For this CPE-CBSD the method of entering the CBRS Installation Parameters to SAS is ‘WlnnForum CPI Multi-Step” (see next section for details).

CPE-CBSD Installation Parameters for “WlnnForum CPI Multi-Step”
The AirSpot1310 CPE-CBSD device is certified under FCC Part 96 rules. This device is a Category B CBSD which must be professionally installed. For this CPE-CBSD the method of entering the CBRS Installation Parameters to SAS is ‘WlnnForum CPI Multi-Step”.
The Mandatory CBRS Installation Parameters to be entered in SAS portal by WlnnForum CPI are the following:

  • FCC-ID: PIDAS1310CPE (verify this FCC-ID on the label of the device)
  • Serial Number: according to the label of the device
  • Category: B
  • Deployment Type: Outdoor
  • Location: according to the location of the device taken by the WlnnForum CPI
    • Antenna Parameters:
    • Gain: 16dBi
    • Horizontal Beam Width: 60 degrees
    • Azimuth: according to the azimuth of the device taken by the WlnnForum CPI
    •  Down Tilt: according to the down tilt of the device taken by the WlnnForum CPI

Important Note: For some SAS portals, the WlnnForum CPI also must enter “CBSD Type: CPE” (NOT “CBSD Type: Base Station”)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals