Summer Doorway 37W Series with Quad Cam Lock Owner’s Manual
- May 15, 2024
- Summer
Table of Contents
Summer Doorway 37W Series with Quad Cam Lock
Safety Information
WARNING
Children have died or been seriously injured when gates are not securely installed.
- ALWAYS install and use gate as directed using all required parts.
- Install according to manufacturer’s instructions.
- Intended for use with children from 6 months through 24 months.
- Stop using when a child can climb over or dislodge the gate.
- Use only with the locking/latching mechanism securely engaged.
- NEVER use a gate to keep child away from pool.
- NEVER leave child unattended.
- ALWAYS close and lock the gate behind you.
- This product will not necessarily prevent all accidents. Proper adult supervision is required at all times.
- Do not use if any components are missing or damaged.
- Adult assembly required. Exercise care when unpacking and assembling product.
CAUTION: Keep small parts out of child’s reach.
Components
Warning
- You MUST install wall cups to keep gate in place. Without wall cups, child can push out and escape.
Gate Configuration
- Measure the width of the opening where you intend to install the gate.
- Baseboard molding may change which configuration is appropriate.
NEVER install both extensions on the same side of the gate.
- A. 29.75″ – 31.25″ without extension frame
- B. 31.75″ – 33.25″ with 2 inch extension
- C. 33.75″ – 35.25″ with 4 inch extension
- D. 35.75″ – 37.25″ with both extensions
Note: This instruction book illustrates installation of gate configuration B.
Installation
- Flip the Cam-Lock levers open.
- Insert the Cam-Locks into the gate as shown. DO NOT CLOSE THE CAM-LOCK LEVERS UNTIL STEP 6.
- Snap the 4 wall cups onto the ends of the Cam-Locks as shown.
- Peel the paper backing off of all 4 wall cups.
- Center the gate in the door frame. Make sure gate is flat and touching the floor as shown. Extend the Cam-Locks with the wall cups attached to secure to the door frame. Push on the wall cups for several seconds to secure them to the door frame.
- NOTE: Make sure gate is properly aligned in the doorway/opening. Refer to page 14 to troubleshoot.
- NOTE: Make sure all wall cups are facing up.
- Push the top Cam-Locks into the wall cups on both sides of the door frame by pushing the silver disc at the end of the rod. While holding in place, push the Cam-Lock lever down on both sides of the gate to secure in place. The red portion of the Cam-Lock will be hidden in the wall cup as shown.
- Tip: This step can be done one corner at a time. If you see red, release the Cam-Lock and repeat step 6.
- Note: Before operating the gate, confirm it is properly installed.
Hardware Mount Installation
IMPORTANT: For use at top of stairs:
At the top of the landing, position the gate a minimum of 3-6 inches (8-15cm) away from the top step.
- With a pencil, trace the entire outline of each wall cup directly onto the wall.
NOTE
- Make sure gate is properly aligned in the doorway / opening.
- Door stop must be opposite to stair side of gate. Gate door must open away from stairs.
- Unlock the lower and upper Cam-locks and wall cups, then remove the gate.
- Hold wall cup in pencil outline from step 1 and mark drill holes with a pencil through the center of each wall cup.
- NOTE: Skip this step and proceed to next step if mounting directly into wood
- Place wall cup over the center of each outline and align hole with your pencil mark or wall anchor. Screw wall cups into wall.
- NOTE: Make sure all wall cups are facing up.
You may now proceed to page 8 to complete installation.
Operation
To unlock gate
- Slide lock tab back to release, lift gate door open.
Confirm the installation
- Make sure gate is secure by pushing on all corners of the gate.
Troubleshooting
- If the gate does not close properly or is not aligned in the door frame.
Solution: Adjust the gate’s alignment by unlocking all four cam-locks and repositioning the gate so that it matches the “correct” image.
Maintenance
- Check all hardware to ensure gate is securely in place. Regularly check the wall cups and cam-locks are not loose.
- Do not use gate if any of the components are damaged or missing.
- Wipe surface with a damp cloth or sponge, using mild detergent and warm water to clean. Towel dry.
Contacts
We’re here to help!
- If you have any questions or need assistance, contact our Consumer Relations Team at
MANUFACTURED FOR
KIDS2, INC. ATLANTA, GA USA 30305 • 1-800-230-8190
IMPORTED BY
- SUMMER INFANT (USA) INC. 1275 PARK EAST DRIVE, WOONSOCKET, RI 02895 USA • 1-401-671-6551
- KIDS2 CANADA CO. PO Box 54059, RPA Lawrence Plaza, Toronto ON, M6A 3B7 • 905-456-8484
- KIDS2 AUSTRALIA PTY LIMITED CASTLE HILL, NSW AUSTRALIA 2154 • (02) 9894-1855
- KIDS2 JAPAN K.K. C/O ARK OUTSOURCING KK 4-3-5-704, EBISU, SHIBUYA-KU, TOKYO, JAPAN 150-0013 • (03) 5322-6081
- KIDS2 UK LTD. GROUND FLOOR, SUITE A1A, BREAKSPEAR PARK, BREAKSPEAR WAY, HEMEL HEMPSTEAD, HP2 4TZ • +44 01582 816 080
- KIDS2 EUROPE BV 5 KEIZERS, KEIZERSGRACHT 287, 1016 ED AMSTERDAM, NETHERLANDS • +31 20 2410934
- KIDS2 US MÉXICO S.A. DE C.V. • (55) 5292-8488
MADE IN VIETNAM
Colors and styles may vary.
Please read the following instructions carefully. Keep this instruction manual
and save for future reference.
Tools required: Phillips head screwdriver and drill (not included). For
technical support, contact us at
1-401-671-6551 or
www.summerbyingenuity.com
For use with children from 6 – 24 months. Keep small parts away from children.
Adult assembly required. Fits openings from 30″ (76.2 cm) – 37″ (94 cm) wide.
Install Video
© 2023 SUMMER INFANT (USA) INC.
©2023 KIDS2, INC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>