REXING 512GB Wireless Solar Powered Outdoor Security Camera System User Manual

REXING 512GB Wireless Solar Powered Outdoor Security Camera System

Thank you for purchasing our Solar lamp camera. For your operating the product easily, we provide an user manual including product introduction and operating steps. Please read this user manual before using the device so as to make sure you can operate the camera correctly. If there is any misprints or inadequate translation, please understand. Then keep this user manual for future reference or product sharing carefully.

Product Overview

1. Energy absorption glass
2. Lens
3. LED light
4. Motion Sensor
5. Photo Mode
6. Off mode
7. Video mode
8. TF card port
9. USB
10. Status indicator LED
11. Charging indicator
12. Reset

Specification

• Image resolution: 2M 1920x1080Solar
• Video resolution: FHD:1920×1080/30fps
• Lens angle: F/NO2.0; FOV=120°;
• PIR sensing angle: 120°
• Triggering distance 8m (Below 77°F/25°C at the Normal Level)
• Memory External memory (Micro SD card upto 512GB)
• PC   interface: Micro USB 2.0
• MIC:   YES
• Solar power: 3.0 W
• Lighting lamp: 4W high power LED, distance 8~10M
• Lighting mode: Lighting below EV3,PIR motion detection lighting, lights off after people go away (lighting lasting most 5 minutes if people always stay by the machine)
• Imaging  mode: Motion detection to triggering taking picture/video
• Operation keypad: Three-stage switch (Video, Image, OFF/Connect PC to setting menu) Reset
• Menu setting: Default triggering continuous shooting 5 pictures, can set to 1~10 picture and photo interval 0~5s; Default triggering video 10s, can set to 3s~5min,Automatic stop after people go away
• Time stamp: Support connect PC to set date and time, and date and time can display on image/video
• Installation height: 1.8-2.5m
• Power: Built-in rechargeable Lithium battery
• Spray-water protected: IP 54
• Operating temperature: -20 to +50
• Storage temperature: -30 to +60
• Dimensions: approx. 225X160X94MM

Before first use

Charging

The Solar lamp camera has an internal, rechargeable battery which must be fully charged before use for the first time. It takes about 20 hours to charge the battery full by.
Please charge the Solar lamp camera by using a common USB power adapter (DC 5V/1A) (not included). While charging the charging indicator LED (11) right to the MicroUSB port will turn RED. When the Solar lamp camera is fully charged, the charging indicator LED (11) will turn off.

MicroSD

Before using the device for the first time or after replacing the MicroSD card, it must be formatted, so as to facilitate the optimization of the Solar lamp camera. The MicroSD card can only be used after the system has been formatted on a PC, which can otherwise lead to errors.

Operation Introduction

Switch

1. When the device switch shows OFF mode, it can be used for charging and downloading with a computer U disk and setting of computer tools.
2. When the device switch shows Video mode,Only available for video.
3. When the device switch shows Photo mode,you can set the photo and photo + video according to the computer tools.

Indicator Light

• The light of Engineering mode

1. Red light:
   The first 30 seconds after power-on, if the battery voltage is normal, the red light will always be on. If the battery power is low (when the remaining power is 20%), the red light will always flash.

2. Green light:
   After starting up 30 seconds,if the animal

• The light of Charging mode

-If it is charged by USB, the charging light will show red and the lights off after charging is complete.
-If the solar charging,the blue light will turn on. No sun the blue charging light will be off.

in
| Flashing all the time| | Battery remaining 20% power or less
| Off| | Needs charging
| Flashing while power on/off| | Needs charging
| | Turns On| Motion is detected (photo / video recording)

Operation

1. Make sure that nothing is blocking the lens and infrared sensor in front of the Solar lamp camera.
2. Switch the Off mode to Photo or Video mode the red light on,the first 30s will enter Engineering mode.
3. Move your hand in front of the motion sensor of the machine (just for testing). The green light (10) will turn on and the red light (10) will turn off once to indicate that the image is recorded/saved.
   Info: After 30 seconds, the green light off will go into hunting mode. The camera will take photos or videos according to the parameters set by your computer (automatic loop is turned on by default).

How do camera, LED and motions sensor work together?

• In the evening,  when the motion sensor detects a moving object (because of infrared sensing light), light lit up to 5 seconds. If the person keeps moving under the camera, the light will stay on for up to 5 minutes. The length of the video is based on the parameters you set via the software on your computer.
• Same video control during the day but the fill light is off.

Parameter Setting

1. Turn the device to the OFF position and connect it to the computer. When the red light of the work instruction goes out, time and parameter settings can be made.

Camera_Config_Tool_exe tools

You can find the following tool virtual disk on your computer

1. Open Camera_Config_Tool_exe tools
   
   

2. Set the Date and Time of camera or PC time.
   After you setting please click the Save Camera Settings to save the setting.
   

3. Formatting TF card
   Before using the device for the first time or after replacing the TF card, it must be formatted,so as to facilitate the optimization of the machine.The TF card is only used after the system is formatted on a PC, which will cause errors. Note: The tool needs to unplug the USB cable after formatting the machine, and then insert it into the PC to correctly display the blank TF card after formatting.

4. Settings
   You could according your need to set the Monitor Mode / Photo Series / PIR Delay / Video Length / Endless Capture / Date / Tme Stamp
   

Watch videos

To watch recorded videos on your PC, set the device into Off Mode and connect the device with a Micro USB cable to your PC. The device now should be recognized as mass storage. In case this does not work insert the Micro SD card directly into the Micro SD card slot of your PC or use a Micro SD adapter card.

Note: If you eject the Micro SD card from the camera you need to format it after inserting to the camera again!

PIR detecting range

Remark: The PIR detection area is 120°. Moreover, the PIR detection range is affected by the environment temperature (25°C is the best temperature).

Battery life

It is depending on the mode you select as a default. Long battery life is one of the most important requirements. There are several variables that will determine the battery life (hours of sunlight, temperature outside, frequency of activity, etc.) Night video and photo frequency (light and record) will result in shorter battery life.

Attention: If RED status LED flashes, it is time for charging!

Installing / Mounting

You can install the solar lamp camera to a tree or fix it to flat surfaces by bracket.

• You should mount the solar lamp camera via bracket in advance.
• The solar lamp camera should be placed, where it has enough sunlight, no barrier and shelter. And the solar panel has to face to the sunlight.
• Place the solar lamp camera above the ground or platform to avoid being inundated by rain.
• Check and make sure the solar lamp camera is fixed well.

Cautions

1. When you connect the computer, the red light is off. Please check if the USB plug is too loose to cause poor contact. When the battery is out of power, it needs to be reset (you can insert a metal strip such as a paper clip into the Reset hole and touch it to reset the machine with a light touch); whether WIN7 prompts the USB due to the high current surge caused by the slow insertion, you need to restart the computer.
2. Before connecting to the computer, the three-gear switch should be set in the OFF position. After connecting to the computer, you can check the pictures and videos and set the computer parameters when the red light is on.
3. When the red light is off at startup, there may be no power to charge. You can use a metal strip such as a paper clip to insert it into the Reset hole and press it to reset it.
4. If the red light keeps flashing when starting up (flash) or the power is turned OFF after starting up for 4 seconds, it needs to be charged, then the three-gear switch should be plugged into the USB 5V computer at the OFF position or the charging cable should be red and red, and the charging red light should be turned OFF when it is fully charged.
5. If the red light keeps flashing (slowly flashing) when you turn on, please check whether the memory card is installed or the cycle is full (connect the computer with the Camera_Config_Tool_exe tool to check whether the machine is closed cycle) and the bad card prompt.
6. 30 seconds after starting up, move your hand quickly outside the machine’s motion sensor. The green light will not flash. Check whether the infrared sensor window is too dirty. After the green light flashes, the red light keeps flashing. Please check whether the MicroSD is properly inserted or not (connect to the computer with Camera_Config Tool exe to format the machine MicroSD card).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>