TIMEGUARD LEDPROSLB Dedicated PIR Detector for LEDPRO Floodlights User Manual
- June 6, 2024
- TIMEGUARD
Table of Contents
LEDPROSLB Dedicated PIR Detector for LEDPRO Floodlights
IInnssttaalllal atitoi onn&&OOp pe reartai nt ign gInIsnt rsutcr tuicotni os n s
Dedicated PIR Professional LEDPROSLB & LEDPROSLWH
1. General Information These instructions should be read carefully and
retained for further reference and maintenance. 2. Safety
off.
3. Technical Specifications
1
Dimensions
78
108 114
TOP VIEW
A
180°
Dusk Level Adjust
C
Delay Time Adjust
SIDE VIEW
12
B
D
Lens Sticker
Less sensitive
More sensitive
Restrict Long Detection
Restrict RHS Detection
Restrict short Detection
Restrict LHS Detection
E
Mains Supply
Note:
Isolation ‘Switch Live’ Switch
3
F
4. Selecting The Location
angles as shown (see diagram A).
to maintain coverage and forward coverage will be reduced. diagram A detailing
detection range and direction.
4
may cause false activation under extreme conditions.
During extreme weather conditions the motion sensor may exhibit unusual behaviour. This
5. Installation
G
IMPORTANT
Switch off the electricity at the fuse box by removing the relevant fuse or
switching off the circuit breaker before proceeding with the installation.
Locking bar
Jumper Plug
bar with one
with the other to reconnect).
5
CONNECTION
mains supply cable
N L
cable from the slave lighting load
to the terminal block on the
N L1
6. Commisioning and Operation Walk Test Procedure The unit can be set up in
daylight or at night. seconds. This indicates the unit is wired correctly. The
unit is in Automatic Mode when the light turns off.
Setting Up For Automatic Operation
6
setting between these limits.
each adjustment to try to get the unit to detect as above.
7. Masking The Sensor Lens
sensor lens using the lens mask sticker supplied (see diagram D). range.
Similarly the left and right lens sections cover the left and right detection
area respectively.
8. Manual Override Mode
17
procedure.
9. Detector Head Adjustment The detector head can be panned 90° to the right
and 90° to the left.
Unit activates during the daytime.
90°
90°
Tilt down
10. Accessing Terminals After Installation
This may be necessary to add further lighting for instance and the following
procedure for removing the unit from its backplate should be followed:Insert
the wire through the hole indicated in diagram F. The terminals are now
accessible. If adding lighting, ensure the unit’s rating is not exceeded.
If you experience problems refer to Troubleshooting Guide. If problems still
exist,
do not immediately return the unit to store.
Telephone the Timeguard Customer Helpline
020 8450 0515
Qualified Customer Support Co-ordinators will be on-line to
8
assist in resolving your query.
11. Troubleshooting PROBLEM
SOLUTION
night and day.
terminals may be transposed.
night, or PIR keeps activation at random for no apparent reason
The unit may be suffering from false activation. Cover the sensor lens completely with black PVC tape. This will prevent the sensor from “seeing” anything. If the unit now switches off after the set time duration and does not re-activate, this indicates that the problem was cause by false activation. The problem may be solved by slightly adjusting the direction/angle of the sensor head (see previous section). If however, the unit
the unit is faulty and should be replaced.
You may not be allowing the unit time to complete it’s warm-up period. Stand well out of the detection range and wait (the warm-up period
Sometimes passages between buildings etc. can cause a “wind tunnel” effect. Ensure the unit is not positioned so as to allow detection of cars/people using public throughfares adjacent to your property. Ensure that the unit is mounted securely, even the slightest movement can result in a false detection.
PIR sensor will not operated
UIT
at all.
breaker/internal wall switch.
wiring connections as per the diagram (see
diagram E).
Ensure no connections are loose.
9
Check the bulb. If the bulb has failed, replace (do not hold bulb directly with fingers, use a tissue or
clean dry cloth).
Ensure that the bulb is seated correctly in the
bulbholder.
The PIR sensor will not operate at night.
Refer to section 4 for DUSK control adjustment.
Unit activates during the daytime.
Refer to section 4 for DUSK control adjustment.
PIR coverage is poor/ sporadic.
Unit may be poorly located. See previous section-“Selecting The Location” and re-locate the unit.
Detection range varies from day to day.
PIR sensors are influenced by climatic conditioins. The colder the ambient temperature, the more effective the sensor will be. You may need to make seasonal adjustments to the sensor head position to ensure trouble-free operation all year round.
3 Year Guarantee In the unlikely event of this product becoming faulty due to
defective material or manufacture within 3 years of the date of purchase,
please return it to your supplier in the first year with proof of purchase and
it will be replaced free of charge. For years 2 and 3 or any difficulty in the
first year, telephone the helpline on 020 8450 0515 .
agreed by Timeguard) the customer is responsible for all shipping/postage
charges is sent.
10
If you experience problems, do not immediately return the unit to the store.
Telephone the Timeguard Customer Helpline;
HELPLINE
020 8450 0515
or email helpline@timeguard. com
Qualified Customer Support Co-ordinators will be on-line to assist in
resolving your query.
For a product brochure please contact:
Timeguard Limited. Victory Park, 400 Edgware Road,
London NW2 6ND Sales Office: 020 8452 1112 or email csc@timeguard.com
www.timeguard.com
67.058.563 (issue 2)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>