TIMEGUARD Professional Rewireable Floodlight Instruction Manual

Professional
Rewireable Floodlight

Installation & Operating Instructions

General Information

These instructions should be read carefully in full before installation and retained for further reference and maintenance.

Safety

• Before installation or maintenance, ensure the mains supply to the floodlight is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or employed for the installation of this floodlight and that it is installed in accordance with current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this floodlight is fitted does not exceed the rating of the circuit cable, fuse, or circuit breaker.
• DO NOT place any object closer than 1 meter in front of the floodlight.

Technical Specifications

• 230V AC 50Hz
• This PIR sensor is of class I construction and must be earthed
• Colour Temperature:4000K
• Energy Efficiency: Class F
• Operating Temperature: -20°C to +40°C
• IP65 Rated, suitable for restricted external applications
• Dimensions (H x W x D): 235 x 305 x 66mm
• CE Compliant

LEDPRO70B & LEDPRO70WH

• 70W LED Non replaceable lamp
• Energy Usage: 70kWh/1000h
• Lumen Output: Black = 7800lm, White = 7800lm

LEDPRO100B & LEDPRO100WH

• 100W LED Non replaceable lamp
• Energy Usage: 100kWh/1000h
• Lumen Output: Black = 12,000lm, White = 12,000lm

Installation

• Ensure the mains supply is switched off and the circuit supply fuses are removed or the circuit breaker turned off.

• An isolating switch should be installed to enable the power to be switched ON and OFF to the floodlight. This allows the unit to be easily switched OFF for maintenance purposes.
  

• Mark the position of the mounting holes on the wall using the U bracket supplied as a template.
  

• Drill the holes for the wall plugs ensuring not to infringe on any gas/water pipes or electrical cables that may be hidden below the surface.
  

• Fix the U bracket to the wall using the correct screws for the wall plugs being used.
  Note: Ensure that when you mount this, the slots at the end of the bracket open upwards to allow you to easily attach and secure the floodlight when ready.
  

• Attach the floodlight to the U bracket fitted to the wall. You can pre-fit the supplied fixing screw/bolt and washers to the floodlight before you do this, the screws/bolts will just need to be loose enough to fit over the upward-facing slots at the end of the U bracket. Make sure the washers are in the correct order as per the diagram. When the floodlight is in place, secure the screws/bolts, ensuring not overtightened.
  

• Pass the supply cable through the holes(s) provided in the backplate ensuring that a cable gland, grommet, or sealing compound is used to maintain the IP rating of the floodlight.
  

• Terminate the supply cable into the terminal block (see section 5.
  Connection diagram) ensuring correct polarity is observed and that all bare conductors are sleeved.

• Attach the backplate to the floodlight, and apply pressure to the top and bottom, then secure all four fixing screws ensuring not overtighten.
  

Connection Diagram

• Connect the 230V 50Hz mains supply cable as follows;

230V 50Hz Mains Supply

Live Supply (Brown or Red) to| L
Neutral Supply (Blue or Black) to| N
Earth (Green/Yellow) to|

Note: the L1 terminal is a Switch Live “Live Output” for slave floodlights (when used in conjunction with the Timeguard LEDPROSLB-WH, LEDPRORFKB-WH PIRs or the LEDPROPCB-WH Photocell).

Operation

• Turn the power ON and test for normal operation.

Lamp Adjustment

• The floodlight can be tilted as per the diagram.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For years 2 and 3 or any difficulty in the first year, telephone the helpline on 020 8450 0515.
Note: A proof of purchase is required in all cases.
For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK. All shipping costs are to be paid in advance before a replacement is sent.
If you experience problems, do not immediately return the unit to the store. Telephone the Timeguard Customer Helpline:
HELPLINE
020 8450 0515
or email helpline@timeguard.com
Qualified Customer Support Coordinators will be online to assist in resolving your query.

For a product brochure please contact:
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email csc@timeguard.com
TW – June 2021
www.timeguard.com
67-058-637 (Issue 3)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>