TIMEGUARD Slimline LED Floodlight Instruction Manual

Slimline LED Floodlight

Installation & Operating Instructions

General Information

These instructions should be read carefully in full before installation and retained for further reference and maintenance.

Safety

• Before installation or maintenance, ensure the mains supply to the floodlight is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or employed for the installation of this floodlight and that it is installed in accordance with current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this floodlight is fitted does not exceed the rating of the circuit cable, fuse, or circuit breaker.
• DO NOT place any object closer than 1 meter in front of the floodlight.

Technical Specifications

• 230V AC, 50Hz
• These luminaires are of class I construction and must be earthed
• Colour Temperature: 4000K
• Energy Efficiency: Class F
• IP65 Rated suitable for restricted external applications
• CE Compliant

LEDPRO10WH & LEDPRO10B

• 10W LED Nonreplaceable lamp
• Energy Usage: 10Kwh/1000h
• Lumen Output: Black: 1160 lm, White: 1160lm

LEDPRO20WH & LEDPRO20B

• 20W LED Nonreplaceable lamp
• Energy Usage: 20Kwh/1000h
• Lumen Output: Black: 2350lm, White: 2350lm

LEDPRO30WH & LEDPRO30B

• 30W LED Nonreplaceable lamp
• Energy Usage: 30Kwh/1000h
• Lumen Output: Black: 3300lm, White: 3300lm

LEDPRO50WH & LEDPRO50B

• 50W LED Nonreplaceable lamp
• Energy Usage: 50Kwh/1000h
• Lumen Output: Black: 5300lm, White: 5300lm

Installation

• Ensure the mains supply is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
  

• An isolating switch should be installed to switch the power ON & OFF to the luminaire.
  This allows the unit to be easily switched OFF for maintenance purposes.
  

• Mark the position of the mounting holes on the wall using the U bracket supplied as a template.

• Drill the holes for the wall plugs ensuring not to infringe with any gas/water pipes or electrical cables that may be hidden below the surface.

• 10W & 20W use 6mm screw peg

• 30W & 50W use 7mm screw peg
  

  • Fix the U bracket to the wall using the correct screws for the wall plugs installed.
    Note: Ensure that when you mount this, the slots at the end of the bracket open upwards to allow you to easily attach and secure the floodlight when ready.
    

  • Secure the supply cable into the junction box through the hole(s) provided ensuring that a cable gland, grommet, or sealing compound is used to maintain the IP rating of the luminaire.
    

  • Attach the strain relief to the luminaire and screw in ensuring not to over-tighten.
    

  • Attach the luminaire to the U bracket fitted to the wall. You are able to pre-fit the supplied fixing screws and washers to the luminaire before you do this, the screws will just need to be loose enough to fit over the upward-facing slots on the end of the U bracket. Make sure the washers are in the correct order as per the diagram. When the luminaire is in place, secure the screws ensuring not to over-tighten.
    

  • Terminate the supply cable into the terminal block (please refer to section 5 connection diagram) ensuring correct polarity is observed and that all bare conductors are
    sleeved.
    

  • Attach the supplied wall plate to the luminaire, apply pressure to catches located on top and bottom, then screw in on both sides ensuring not to over-tighten.

Connection Diagram

Connect the 3 core mains supply cable to the block on the unit as follows:

Live Supply (Brown or Red) to| L
Neutral Supply (Blue or Black) to| N
Earth (Green/Yellow) to|

Note: the L1 terminal is a Switch Live ‘Live Output’ for slave floodlights (when used in conjunction with the Timeguard LEDPROSLB/WH PIR or LEDPROPCB/WH Photocell)

Operation

• Turn the power on to the isolating switch and test for correct operation.

Lamp Adjustment

• The lamp can be tilted 360º turn through U-Bracket.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For years 2 and 3 or any difficulty in the first year, telephone the helpline on 020 8450 0515.
Note: A proof of purchase is required in all cases.
For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK. All shipping costs are to be paid in advance before a replacement is sent.

If you experience problems, do not immediately return the unit to the store. Telephone the Timeguard Customer Helpline:
HELPLINE
020 8450 0515
or email helpline@timeguard.com
Qualified Customer Support Coordinators will be online to assist in resolving your query.

For a product brochure please contact:
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email csc@timeguard.com
www.timeguard.com
67-058-561 (Issue 2)
TW – June 2021

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>