SEALEY Air Line Pressure Gauge Tyre Inflator Clip User Manual

INSTRUCTIONS FOR:
PROFESSIONAL AIR LINE GAUGES
MODELS: SA9302 & SA9312

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS FOR FUTURE USE.

SAFETY INSTRUCTIONS

Disconnect the gauge from the air supply before changing accessories, servicing or performing any maintenance.
Maintain the gauge in good condition (use an authorized service agent), and keep the gauge clean for best and safest performance.
Replace or repair damaged parts. Use recommended parts only. Unauthorized parts may be dangerous and will invalidate the warranty.
Locate gauge in a suitable work area, keep the area clean and tidy and free from unrelated materials and ensure there is adequate lighting.
Keep children and unauthorised persons away from the work area.
DO NOT direct gauge outlet at yourself or at other persons or animals.
DO NOT carry by the hose, or yank the hose from the air supply.
DO NOT use the gauge for a task which it is not designed to perform.
DO NOT operate the gauge when you are tired or under the influence of alcohol, drugs, or intoxicating medication.
DO NOT operate the gauge if parts are missing or the gauge is damaged, as this may cause failure and/or personal injury.

INTRODUCTION & SPECIFICATIONS

SA9302: Composite body and dial type gauge with rubber protector. Calibrated in bar/psi. Fitted with a 500mm rubber hose and single clip-on connector.
SA9312: Composite body and dial type gauge with rubber protector. Calibrated in bar/psi. Fitted with a 500mm rubber hose and a twin push-on connector.

INSTALLATION

3.1 INSTALLATION FOR BOTH MODELS
3.1.1 AIR SUPPLY – MAXIMUM PRESSURE 12bar (175psi)
The supply must be clean and dry – use a suitable filter/water trap if necessary. The supply pressure at the gauge inlet should ideally be 10bar (145psi).
Note: Maximum tyre inflation pressure cannot exceed the supply pressure.

OPERATION

4.1 ATTACH ADAPTOR TO VALVE
Push and hold the connector onto the tyre valve using the most convenient side of the twin valve connector (SA9312).
For SA9302, squeeze the thumb clip on the connector, push the connector onto the tyre valve and release the clip.
The connector will now be locked in place.
4.2 TO INFLATE
Momentarily depress the operation lever fully, then release to display tyre pressure. When reading the pressure, hold the gauge “flat” with respect to the eye to minimise error.
Fully depress operation lever for an appropriate period. Avoid overinflation, release the lever frequently to check the pressure.
4.3 TO DEFLATE
Depress lever halfway (until air can be heard escaping) for an appropriate period. Fully depress lever momentarily then release to display new pressure.
IMPORTANT – ALWAYS FULLY DEPRESS LEVER MOMENTARILY BEFORE READING TYRE PRESSURE.

MAINTENANCE & SERVICE

PERIODIC CHECKS AND MAINTENANCE
For long service and accuracy, the following actions should be carried out at the recommended intervals.
5.1 WEEKLY – CHECK OPERATION
The gauge should be checked weekly for correct operation. Look for smooth lever operation and fast, smooth gauge movements. Check for leaks from tyre connector seals, and for chafing or wear of the flexible hoses. Any problems should be immediately rectified.
5.2 QUARTERLY – CHECK CALIBRATION
We recommend the accuracy of the gauge is checked against a calibrated “master” gauge every 3 months, or at shorter intervals depending on the operator’s own quality procedures.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of these products.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
SA9302 & SA9312 – 1 – 091105

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>