MEES M1 TWS Wireless Earbuds User Manual

User manual

Accessories

charging case

Select one earbud as main earbud
Remark : Make sure the other earbud is in the charging case

Search the Bluetooth list from the device, and choose “M1(R) or (L)”
You will hear “connected” Pairing is done and succeed. If require, Please input “0000” as a Bluetooth password

Pick up the other earbud  from the charging case
You will hear “Power on” and “TWS connected”

M1 remember devices it’s not necessary to Repair, Enable Bluetooth on your device, it’ll reconnect automatically.
Note : All calls will be heard in the Main earbud only.

Best fit & best sound
Try all the ear tips to find the best fit and the best sound. The fit is right when you get a complete seal, the ear tips feel comfortable, and you get the best quality and loudest sound.

Insert the earbuds with the ear tip directed towards your ear canal. Twist gently until fit comfortably and feel secure in your ear. Insert the earbuds with the ear tip directed towards your ear canal. Twist gently until fit comfortably and feel secure in your ear.

Tip: More than one eartips size may fit you. Choose the one that completely seals your ear canal for the best sound. You may need different size ear tips for left and right.

M1 basics
Power On/Power off
Pick up earbuds from the charging case, earbuds will be power on automatically, you will hear “Power on”Put the earbuds into the charging case, earbuds will be power off and start to charge, you will hear “Power Off”

Short press
| Previous song
Long press| | Next song
Long press

Charge the earbuds
Put the earbuds into the case.
Push back the case until it is completely closed.
The earbud green light turns on when it is charging and the light turns off when it is completely charged.
Charge the case
Charging the case by plugging in the charging cable. The case light turns on when it is charging.

Charge level
Your earbuds let you know when your battery level is low. Every 20 seconds you will hear“Battery low” when there is 2 minutes of battery level.

Earbud status lights

Case status lights
When your case is plugged into a charging cable for charging, you will see charging lights.

Note: Your battery is designed to last the life of the product. It should only be removed by a recycling facility. An attempt to remove or replace your battery will damage the product and void your warranty.

Basic Specifications of Earphone

Size: 23.6×16.5×26.7mm
Weight: 4.5g
Earbuds Charging Current:55mA
Earbuds Charging time: 1 hour
Working Voltage: 3.3V~4.2V
Standby time: about 40 hours Music Time:2~2.5 hours
Talking Time:2 hours
Bluetooth version: Bluetooth 4.2
Support Profile: HSP, HFP, A2DP, AVRCP
RF transmit: Class-2
Transmission Range (Hz): 2.40GHz ~ 2.48GHz
Transmission distance: 10m
Audio sampling accuracy: 16bits
Audio sampling rate: 44.1~48kHz
Audio encoding format: CVSD、MSBC、SBC、AAC
SNR: >95dB
Working temperature: -15℃～+60℃
Working humidity: 10%~85%( in a non-frozen state)
Earbud Speaker Specifications
Speaker specifications / mode: Φ6mm
Impedance: 16Ω/ TYP.
Frequency(Hz): 20Hz～20KHz
Sensitivity: 93±3dB
Input Power: 2.0mW (Normal), 5mW (Maximum)
Earbud MIC Specifications
1. MIC type: Silicon MIC
2.MIC sensitivity: -42±3dB
3. SPL：130dB
Basic Specifications of Charging Case
Size: 593424mm Weight:27g
Charging Port: Micro
Charging base(Full) provide power to earphone: 2 times
Charging time: 2hrs

Safety instructions for use
To avoid hearing damage, keep the volume at a moderate level. Avoid listening to music at loud volume levels for prolonged periods of time as this may cause permanent hearing damage or hearing loss.  Do not use M1 when it is unsafe to do so. For example, while operating a vehicle, cycling, crossing a road, or any activity which requires yourattention and ability to hear.
Note : If you are watching video while using your earbuds, your audio may be slightly out of sync with your device. Safety Warning Please disconnects the USB cable after charging. The product should not de charging for a long time. Please use the charger or adaptor with output voltage and current(max) 5V/1A or 5V/1.5A and product original charging cable for the product charging. lf the output voltage and current of the charger exceeds the requirement, it will cause severe damage to the product, and the product warranty will be invalid.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>