drive BLS18FBD-SF Blue Streak Wheelchair User Manual
- June 12, 2024
- Drive
Table of Contents
drive BLS18FBD-SF Blue Streak Wheelchair
Please read this manual carefully to insure safe usage and understanding of maintenance instructions. Congratulations on your purchase of a Drive wheelchair. Drive wheelchairs are a product of quality engineering and are manufactured to meet our own highly rigid specifications and will surpass all your expectations.
Use and Safety
WHEEL LOCKS – Engage both wheel locks before getting in or out of the chair, leaning forward in chair, or while in an elevator or wheelchair lift. Proper adjustment of wheel lock is at least 1/8” when locked. Locks are engaged by pushing handle completely forward. Adjustments to locks are made by loosening or tightening nut on the carriage bolt. Embed lock shoe at least 1/8” by sliding the clamp toward the rear wheel while handle is engaged in the locked position. Tighten nut and bolt to secure in position. Test for correct locking action before actual use.
TIRES – Solid rubber tires need minimal maintenance, but should be cleaned occasionally with a damp cloth. Replace if tires become severely worn or cracking appears.
FRONT CASTERS – Casters should be checked periodically and lubricated occasionally. Lubricate by removing the fork and greasing the caster stem bearings. Lubricate wheel bearings by removing the wheel from the fork. Reassemble fork and wheel by tightening nuts until no play remains, but wheels roll freely. If nut is too loose, caster will shimmy, if too tight, chair will be hard to steer.
REMOVAL OF SWING-AWAY FOOT RESTS/LEG RESTS – Release lock by pushing on the front rigging lever. Swing-away footrest/leg rest out and sideways. Lift to remove.
ADJUSTING LENGTH OF FOOTREST/LEG REST – When adjusting length of foot rests or leg rests, the user should be sitting in a wheelchair with feet on the footplates. Loosen bolt on the clamp around support assembly. Raise or lower foot plate to desired position that will provide maximum support of thighs. Front rigging should not be so low that it causes uncomfortable pressure to thighs at front of seat upholstery. Footrest should not be lower than 2-1/2” from the ground to ensure clearance.
ADJUSTING/ELEVATING LEG REST – Lift the foot plate on leg rest assembly to desired position. Release leg rest assembly and it will automatically lock into place. To lower, push out on leg rest lever and lower foot plate to desired position.
WHEELS – Large rear wheels should be inspected at least once a month to ensure proper tightness. If wheel wobbles or is loose, release lock nut and tighten axle bolt slightly. Test for proper tightness by learning chair to one side and spin adjusted wheel.
GENERAL CARE – Wipe chrome parts with a clean, soft cloth at least once a week. All metal parts can be cleaned with auto wax or similar poducts. If exposed to moisture, dry immediately. Do not use an abrasive cleanser that will scratch the finish.
TO OPEN CHAIR – Open the wheelchair by tilting to one side and pushing down on seat rail until fully opened.
TO CLOSE/FOLD CHAIR – First fold foot plates to vertical position. Grab seat with both hands at front and back edge and lift. Or, tilt chair to one side and lift up on seat rail.
REMOVABLE ARMS – Remove arms by depressing the spring button and lifting arms out of front and rear sockets.
WARNING
Do not attempt to adjust or operate a wheelchair without reading carefully all
instructions in this manual.
This wheelchair has not been approved as a seat that can be used within vehicles of any kind. Always transfer wheelchair users to a vehicle manufacturer’s approved seat and use the safety restraints available. Do not operate this wheelchair on roadways, streets or any surfaces with vehicular traffic. Do not attempt to operate on inclines 10% or greater without proper assistance. Be sure to completely engage wheel locks when getting in and out of a wheelchair or when in an elevator or wheelchair lift. The wheelchair should be on a smooth, stable and level area with wheel locks engaged before transferring user in or out of wheelchair. Do not adjust foot rests any lower than 2-1/2” from the floor. When getting in or out of the wheelchair, do not stand on or apply weight to footrests. Before reaching or leaning forward, rotate the casters to the front of the wheelchair engage wheel locks to help prevent the wheelchair from tipping over. Do not lean over or apply weight to the top of the wheelchair back. This can cause the wheelchair to tip over. When trying to extend your arms over your back, only reach as far as your arm can extend without having to alter your seating position. DO NOT stand on a wheelchair. DO NOT use wheel locks to slow your descent down an incline. Abruptly changing directions while going down an incline could cause instability or possible tipping over
WEIGHT CAPACITY: 250 LBS
CAUTION:
Stability – The wheelchair is designed to be safe and stable as long as the center of gravity is maintained while going about normal activities. Care must be taken while performing activities that shift your center of gravity in the chair. Never reach so far that requires you to shift in the seat or bend over out of the chair. When you have to reach for objects that require you to lean, be certain front casters are pointing in a forward position that extends the wheelbase and will stabilize the chair.
Ramps – Be sure of your own capabilities, limitations, and strength before attempting to go up a ramp. Correct techniques on ramp negotiation should be shown to you by a qualified professional. Assistance is recommended when going up or down inclines greater than 10o. If you must stop on an incline, avoid sudden, abrupt movement when you resume movement. Because of the backward angle of the chair, sudden abrupt movement could cause instability. Attempting to use the wheel lock brakes could result in accidental locking, tipping to one side, or causing a sudden stop. Avoid changing direction when going down an incline, as this could result in instability of tipping over.
3 year limited warranty
Your Drive brand product is warranted to be free of defects in materials and workmanship for three years of the original consumer purchaser. This device was built to exacting standards and carefully inspected prior to shipment. This 3-year Limited Warranty is an expression of our confidence in the materials and workmanship of our products and our assurance to the consumer of years of dependable service. This warranty does not cover device failure due to owner misuse or negligence, or normal wear and tear. The warranty does not extend to non-durable components, such as rubber accessories, casters, and grips, which are subject to normal wear and need periodic replacement. If you have a question about your Drive device or this warranty, please contact an authorized Drive dealer.
- 2012 Medical Depot, Inc. All rights reserved. The drive is a trademark of Medical Depot, Inc. Port Washington N.Y. 11050 USA Made in China
- EU Authorized Representative
- Drive Medical LTD
- Ainley’s Industrial Estate
- Elland, West Yorkshire,
- United Kingdom HX5 9JP