MEES DA MS6439 Wireless Open-Ear Headphones Instruction Manual

: June 12, 2024
: MEES

Table of Contents

MS6439
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MS6439

Instruction Manual Of Full Open Earcuff

FCC ID：2AR23-MS6439

1. Phone Pairing Guide

(1) Phone pairing: Open the Bluetooth function menu on the phone, and select MS6439 for pairing and connecting. When successfully paired and connected, the blue lights of the left and right earphones are on for 1 second and then go out, accompanied by the “connected” prompt tone. When the phone is disconnected, the blue light of the primary earphone flashes, and the secondary earphone is without light, accompanied by a “disconnected” prompt tone.

Paired Connection Disconnect

The blue light is on for 1 second and then goes out “Connected” prompt tone
L: Left earphone (primary earphone)
R: Right earphone (secondary earphone)

(2) Back-connect mobile phone: If there is a mobile phone that can be connected back after the earphone is taken out from the case, the mobile phone will be automatically connected back. The blue lights of the primary and secondary earphones are on for 1 second and then go out without prompt tone.

(3) Over-distance back-connection: Connect back after the distance is exceeded, the primary earphone light flashes to start the pairing, and the blue light is on for 1 second after the back-connection. The disconnection is accompanied by a “disconnected” prompt tone, and the back-connection is accompanied by a “connected” prompt tone

Note: You have about 5 minutes to connect the earphone to your phone, otherwise the earphone will exit the pairing mode, the blue light of the primary earphone flashes, and the secondary earphone is without light. Then the earphone will turn off and enter the deep sleep state. Put the earphone back into the charging case, close the cover and open the charging case again, and take out the earphone and re-start pairing.

2. Method of Operation

Multifunctional touch control area (Music/Call/Mode Switch)

		L: Left earphone	R: Right earphone
Music (music playing)	Play/Pause	Double click	Double click
Next song	–	Press and hold for 2 seconds
Previous song	Press and hold for 2 seconds	–
Call (call from others)	Answering/Closing	Double click	Double click
Reject a call	Press and hold for 2 seconds	Press and hold for 2 seconds
Mode switching	Voice Assistant	–	Triple click
Game space sound effects	Triple click	–
Basic Functions	Power on (Shutdown status outside the case)	Press and
hold for 2 seconds	Press and hold for 2 seconds
Power off (When no device is connected)	Press and hold for 5 seconds	Press

and hold for 5 seconds
Clear device records and mode memory| Penta click| Penta click

3. Wearing Mode

Wearing method: Hold the ear tip with one hand and lift it upwards, hold the earphone with the other hand and buckle it in at the middle and upper part of the ear, then move it down to the middle of the ear, and finally push it in and fix it to finish the wearing of the earphone.

4. Earphone Parameters:

Each earphone size: 272417mm
Weight:(Each earphone: 5.9g)
Charging current of dualearphones: 60mAh*2
Earphone charging time: about 1.5H
Stand-by time of earphone: about 70H
Music stand-by time : about 9H
Full-power talk time: about. 6H
Operating temperature:-10°C~+55°C
Operating humidity: 10%-85%(non-frozen)

5. Bluetooth Parameters:

Bluetooth version: 5.2
Bluetooth protocol: A2DP/AVRCP/HFP/SPP
Bluetooth transmission range: 2.40GHz~2.48GHz
Communication distance: 10m

6. Loudspeaker Parameters:

Loudspeaker type: moving coil loudspeaker
Loudspeaker specification: 17*12 mm
Loudspeaker impedance: 18 ± 15% Ohm
MIC sensitivity:-38±1dB
MIC frequency response range: 20Hz~10KHz

7. Charging Case Parameter:

Size: 584525mm
Weight (without earphones): 33.1g
Charging input interface: USB-C charging port
Battery capacity: 350mAh
Full charge time: about 1.5H

Customer FAQs Answers

Q1: How to solve the problem that one side has no sound or is not synchronous when both earphones are being used?****

A. Try putting the earphone back into the charging case, turn it off and remove the earphone again.
B. If the two earphones cannot be automatically connected after repeated removal, it is mostly because the left ear or right ear is used alone and other wrong operation leads to the disconnection of the two earphones.
Follow the steps below to reconnect the two earphones.
1. Put the earphone back into the charging case and turn it off.
2. Find and delete “MS6429” from the phone list.
3. Refer to the pairing guide to pair again.

Q2: How to solve the problem of earphone jamming and intermittent?****

A: Adjust the angle of wearing the earphone according to point 6 of the instruction manual or put the earphone back into the charging box and take it out again.

Q3: How to solve the problem of earphone touch failure?****

A: Water or oil stain on the surface of the touch area of the earphone may lead to poor touch control of the earphone. Try wiping off the earphone and cleaning finger surfaces before retrying.

Q4: What can I do if the earphone cannot connect and I want to reset the earphone?****

A: Clear the pairing information connected with the earphone on the device, and re-pair according to the Bluetooth pairing parts in point 3 and point 4 of the instruction manual.

Q5: Can the earphone be soaked in water or worn when swimming, bathing or being in heavy rain?****

A: The MS6439 is dust-proof and waterproof to the lPX6. Sweat from running or other physical exercises is OK, but it cannot be submerged.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.