HOLO AUDIO R2R-DS1024 Digital to Analog Converter User Manual

R2R-DS1024 Digital to Analog Converter
User Manual

OVERVIEW

Spring3
A new generation DAC of a fully discrete resistor network (commonly known as R2R). Relative to its predecessor the “Spring 2”, the following improvements have been applied.

FEATURES

• A new generation of linear compensation technology. It’s a better solution to the resistance and accuracy errors caused by the switching components and the PCB. After compensations have been applied, the equivalent accuracy will be 0.00005%.
• The new generation of de-glitch technology can provide a full range without increasing the noise floor or other adverse effects.
• Based on this new generation of technology, “5R3” Spring3 can provide a SINAD of > l l 2dB and a dynamic range of > 128dB, which represents the performance limit reached by today’s most advanced R2R architecture DAC.
• Using the ultimate performance of PLL+FIFO technology, which provides 0.1 Hz: Third-Order low-pass ability to inhibit jitter. It also uses a high-performance femto­ second VCXO as the PLL clock source. Under the premise of being almost immune to the front-end jitter, it can also lock up to 1.5us-2us @ 1 kHz signal with high jitter.
• The USB interface uses proprietary firmware with ultra-low latency, a highly reliable data transmission, and ideal USB eye pattern measurements that contribute to 2-4 times higher performance than official firmware.
• A single, independent HDMI-I25 input interface is provided, which has a four-way independent circuit, as opposed to a standard LVD5 chip, making 125 clock signals subject to lower interference and lower jitter. In addition, the 125 input can be configured with a specific pinout configuration, making it compatible with most of the  HDMI-I25 digital devices on the market.
• Optional (Factory installed only): A fully balanced, fully discrete analog pre-amplifier. Provides 84 steps, each step is 1 dB of volume control.

SPECIFICATION

DIGITAL INPUT

DSD 64X (DOP)
USB| PCM 44.1 K-1.536M (32bit)
DSD 64-512X ( DOP )
DSD 64-1024X (Native)
I²s| PCM 44.1 K-1.536M (32bit)
DSD 64-1024X

ANALOG OUTPUT

DNR 127dB
DAC Voltage Output 2.9Vrms (RCA), 5.8Vrms (XLR)
(Optional) Pre-amplifier Voltage Output 5.8Vrms (RCA), 11.6Vrms (XLR)
DSD 128X| THD+N 0.00035% @1K(-109dB)
DNR 115dB
DAC Voltage Output 1.4SVrms (RCA), 2.9Vrms (XLR)
(Options l) Pre-amplifier Voltage Output 2.9Vrms (RCA), 5.8V (XLR)

PHYSICAL CHARACTERISTICS

Size (Chassis)| 430x300x55mm (W x L x H, Dimensions do not include protruding parts)
---|---
Weight| 8.5kg

POWER SPECIFICATION

Power Input (configurable, see label on the bottom of the unit for specified input)| 220-230V 50/60Hz – Fuse Type 2A SB 5x2Omm
---|---
110-115V 50/60Hz – Fuse Type 4A SB 5x2Omm
Power Consumption| 40W

ACCESSORIES

USB Cable xl
Remote Control xl (Not included in Level 1 models)

FRONT PANEL

BUTTON CONFIGURATION

POWER, MUTE, MENU, ←/ Volume -,→ / Volume +
Left of display
POWER (INDICATION LIGHT IS RED HEN POWER IN OFF-STATE AND GREEN HEN ON)
Press and hold this button for 1 second to switch the power on and off. In the off state, all is power is off except for the standby circuit and red indication light, other circuits of the Spring 3″*3″ will stop working and stop outputting.
Right of the display, 4 buttons from left to right
MUTE
In the silent mode, some of the Spring 3 ‘0.3″ output stage circuit turns off. However, the power consumption is essentially unchanged and will maintain its hot machine state.

MENU

In normal operation mode press this button to select the digital input (Source) mode, use the arrow buttons, F and —> to select USB (ground isolation), 125, RCA, BNC, AES, and fiber optic.
In-display mode (Display), use the arrow keys e and -+ to select whether to turn off the display (Display Off) automatically; in configuration (Menu) mode, press this button to select the configuration item.
←/VOLUME
In configuration mode, press this key to change the configuration items. (Volume – only applies when pre-amp module installed.) In the normal mode, press this key to decrease the output volume.
→/ Volume +
In configuration mode, press this key to change the configuration items. (Volume + only applies when pre-amp module installed.) In the normal mode, press this key to increase the output volume.

CONFIGURATION MODE

How to enter Configuration mode:
In shutdown mode (powered off state, red light indicated) press and hold the menu button and power button to enter menu mode. Then press the menu button to select the configuration mode, press the left button or right button to change the configuration mode.
CONFIGURATION MODE OPTIONS (IEFT TO RIGHT SELECTION )

12S FAT

Select from HOLO, ALT1, ALT2, ALT3. Reference 125 Port Pinout for an explanation and the 125 line sequence. (See page 08)
OUTPUT
STANDARD, the analog RCA output is normal polarity, balanced XLR output 1 -Ground, 2-Hot, 3-cold.REVERSED, the analog RCA output is reverse polarity, balanced XLR output 1-Ground, 2-Cold, 3-Hot.
PLL
Select ON to turn on the PLL function and work with all digital input signals to eliminate Jitter. Select OFF to turn off the PLL function.

REAR PANEL

REMOTE CONTROL

This remote control is a universal remote control for HOLO AUDIO. The sampling mode setting and analog output setting buttons are invalid for the “M3” Spring 3; the volume (+/-) button is only available for configuration with preamplifier. This remote will work simultaneously with other HOLO Audio branded products i.e. DACS, pre-amps, and head-amps.

125 PORT PINOUT

Using LVDS differential transmission. Physical interface and HDMI consistent, you can use the HDMI cable. But note that the electrical signal transmission is 125, not conventional HDMI audio and video signals.

R-
4| 12S_BCLK+| DSD_BCLK+| 12S_BCLK+| DSD_BCLK+| 12S_BCLK+| DSD_BCLK+| 12S_BCLK+| DSD_BCLK+
5| GND| GND| GND| GND| GND| GND| GND| GND
6| 12S_BCLK-| DSDBCLK-| 125 BCLK-| DSD_ BCLK-| 12S_BCLK-| DSD_BCLK-| 12S_BCLK-| DSD_BCLK-
7| 12S_LRCK-| DSD_R-| I2SL _RCK+| DSD_R+| 12S_LRCK-| DSD_L-| 125_LRCK+| DSD_L+
8| GND| GND| GND| GND| GND| GND| GND| GND
9| I2S_LRCK+| DSO_R+| 12S_LRCK-| DSD_R-| 12S_LRCK+| DSD_L+| 12S_LRCK-| DSD_L-
10| 12SMCLK+ DSD MCLK+| I2S_MCLK+| DSD_MCLK+| 12S_MCLK+| DSD_MCL K+| 12S_MCLK+| DSD_MCLK+
11| GND| GND| GND| GND| GND| GND| GND| GND
12| 12SMCLK- DSD MCLK- 125_ MCLK-| OSD_MCLK-| 12S_MCLK-| DSD_MCLK-| 12S_MCL K-| DSD_MCLK-
13| NC| NC| NC| NC| NC| NC| NC| NC
14| NC| NC| NC| NC| NC| NC| NC| NC
15| NC| NC| NC| NC| NC| NC| NC| NC
16| RSV| RSV| NC| NC| NC| NC| NC| NC
17| GND| GND| GND| GND| GND| GND| GND| GND
18| NC| NC| NC| NC| NC| NC| NC| NC
19| GND| GND| GND| GND| GND| GND| GND| GND

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>