Freedompro 4C 5 A 110-230 V Audio Visual Intelligence Instructions

Freedompro 4C 5 A 110-230 V Audio Visual Intelligence

Wiring option 1 Wiring option 2

Read before use

Caution!
Follow the illustrated wiring diagram exactly.

Caution!
Output loads must be connected to the same supply voltage of the device.

Legend:

• O1: Load circuit 1 output terminal (Max 5 A)
• O2: Load circuit 2 output terminal (Max 5 A)
• O3: Load circuit 3 output terminal (Max 5 A)
• O4: Load circuit 4 output terminal (Max 5 A)
• S1: Switch (controlling O1) input terminal
• S2: Switch (controlling O2) input terminal
• S3: Switch (controlling O3) input terminal
• S4: Switch (controlling O4) input terminal
• SC: Switch common output terminal
• L: Live (110-240 V AC) terminal
• N: Neutral (110-240 V AC) terminals

Caution!
Neutral fusing: disconnect mains supply before servicing.

Caution!

• The installation of the device must be carefully performed by a qualified electrician.
• Any changes to the wiring must only be carried out after ensuring that there is no voltage in the electrical system.
• Install the device in a protected, dry environment and inside the building.
• Do not connect devices to the module that exceed the maximum load indicated.
• Install the module only on power grid and appliances that meet applicable standards.
• A short circuit in the mains supply or any device connected to the module may cause damage to it.
• Connect the module only as instructed in this manual. Any other method may cause damage and void the warranty.
• Install a 20 A circuit breaker with impulse withstand voltage (Uimp) of at least 4 kV and compatible voltage rating on the AC side of the device.
• The device may be connected with heat resistant (not less than 105 °C) solid-core 18-12 AWG cables.

Installation

1. Disconnect the power from the system.
2. Attach the device to the DIN rail of an electrical panel or inside a junction box. After the installation, only the central part of the front panel may be accessible to the user.
3. Remove the covers from the terminals with the help of a screwdriver.
4. Connect the accessory cables to the top connectors as shown in the diagrams.
5. Connect the control cables to the lower connectors as shown in the diagrams.
6. Connect the power supply to the device as shown in the diagrams.
7. Check that the wiring is correct and restore the power supply to the electrical system.
8. Reapply the covers over the terminals.
9. After connecting the device and powering it up, use the Freedompro app and follow the instructions to proceed to the final configuration step.

Technical specifications

• Power Supply: 110-240 V AC 50/60 Hz
• Max load per channel: 5 A / 240 V 50/60 Hz
• Radio protocol: Wi-Fi 2.4 GHz IEEE 802.11b/g/n
• Radio TX Power: < 20 dBm
• Frequency: 2412-2484 MHz
• Dimension: 2 DIN module 90 x 36.1 x 32.2 mm
• Operating temperature: -20 °C up to +45 °C
• Complies with: RE Directive 2014/53/EU
• Safety & Health: (Art. 3.1 a) EN IEC 62368-1:2020 + A11:2020,EN IEC 62311:2020
• EMC: (Art. 3.1 b) ETSI EN 301 489-1 V2.2.3, ETSI EN 301 489-17 V3.2.4
• Radio: (Art. 3.2) ETSI EN 300 328 V2.2.2

Status LED

• Fixed blue: System ready
• Flashing blue: Pairing mode
• Flashing green: Identify
• Fixed magenta: No Wi-Fi connection
• Flashing magenta: No internet connection
• Fixed red: System boot
• Flashing red: Error
• Fast flashing red: Factory reset

If the instructions in this manual are not followed correctly, this may result in malfunction, danger to health and life, violation of laws, or voiding of legal and/or commercial warranties (if any).
Freedompro is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure to follow the user and safety instructions in this guide.
Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
To control this HomeKit-enabled accessory, the latest version of iOS or iPadOS is recommended.
For more information, please visit: https://freedompro.eu/

References

• Freedompro | Build your smart home, module by module

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>