ProPlex Floppy Drive DIN Rail User Guide

June 6, 2024
ProPlex

ProPlex Floppy Drive DIN Rail- logo

ProPlex Floppy Drive DIN Rail- DIN Rail

ProPlex FloppyDrive DIN Rail
Quick Start Guide

Setup

ProPlex DIN Rail devices use a standard Phoenix MSTB screw terminal connector in various pin configurations. Please refer to the wiring diagrams below for correct hook up of your ProPlex DIN Rail product.

The ProPlex FloppyDrive DIN Rail can operate at 12 or 24 VDC. The required voltage of the LED product to be used determines the required voltage of DC supplied to the FloppyDrive. For example, when using Firefly FloppyFlex RGB LED Neon requiring 24V, a 24 VDC power supply must be used. When using 12V generic RGB LED tape, a 12 VDC power supply must be used.

The FloppyDrive DIN Rail can drive a maximum of 36 Watts per channel at 12V, or 72 Watts per channel at 24V. Please check the power consumption of the product to be
driven with the FloppyDrive to confirm the maximum length that can be attached to the two outputs of three channels.

Addressing and mode selection is done via RDM protocol.

  1. Connect the DC power (12/24V) to the power input located in the left top corner. The connector should be wired as follows:
    1.1. Because the FloppyDrive DIN Rail is capable of over 8 amps of current consumption, it is imperative that the power supply power leads be doubled for each polarity when the supply is 12V to keep the current below 10 amps per conductor and per screw terminal. When using a 24V supply, only one conductor per polarity is required. See diagram below for correct connection of the DC power supply.
    ProPlex Floppy Drive DIN Rail-Because the Floppy

  2. Connect the DMX signal input to the DMX input located in the right top corner of the unit. The connector should be wired as follows:
    2.1 To pass DMX to another device, connect the DMX cable to the DMX Thru port located in the right top corner of the unit. The connector should be wired as follows:

  3. Connect the LED product to the LED strip outputs. Each output is three channels of constant voltage, 12/24V output. The maximum load when the FloppyDrive is powered by 12 VDC, is 36 Watts per channel. The maximum load when the FloppyDrive is powered by 24 VDC, is 72W per channel. *Please consult the manual of the product to be used to determine the overall loads.
    The connectors should be wired as follows:
    ProPlex Floppy Drive DIN Rail- The connectors

Connection Scheme for RGB Products

ProPlex Floppy Drive DIN Rail-TConnection

Basic Scheme for Single-Color LED Products

ProPlex Floppy Drive DIN Rail-TBasic Scheme

Connection scheme for DMX Thru-Port usage.

ProPlex Floppy Drive DIN
Rail-Connection

Dimensions and Connections

ProPlex Floppy Drive DIN Rail- Connections

ProPlex Floppy Drive DIN Rail-Connect

LED Status Information

ProPlex Floppy Drive DIN Rail-B Information

The Power LED has two states: ON and OFF.

  • ON: Unit is receiving power
  • OFF: Unit is not receiving power

The DMX input activity LED has two states: OFF and BLINKING YELLOW.

  • OFF: There is no active incoming DMX signal.
  • BLINKING YELLOW: There is an active incoming DMX signal.

DMX values for each LED strip output

Channel Value Function Output Number
1 000 ↔ 255 RED intensity 0% – 100% (or Color 1) 1
2 000 ↔ 255 GREEN intensity 0% – 100% (or Color 2) 1
3 000 ↔ 255 BLUE intensity 0% – 100% (or Color 3) 1
4 000 ↔ 255 RED intensity 0% – 100% (or Color 4) 2
5 000 ↔ 255 GREEN intensity 0% – 100% (or Color 5) 2
6 000 ↔ 255 BLUE intensity 0% – 100% (or Color 3) 2

Note: The ProPlex FloppyDrive DIN Rail controller is designed for “constant voltage” RGB or Monochromatic LED 12V or 24V products via DMX. Depending on the input power (12V or 24V), the maximum output power varies:

Maximum power at 12V: 36W per channel.
Maximum power at 24V: 72W per channel.
CONTACT INFORMATION

LOS ANGELES HEADQUARTERS
527 Park Avenue | San Fernando, CA 91340, USA
Tel: +1 818.899.8818 | Fax: +1 818.899.8813
sales@tmb.com

LOS ANGELES +1 818.899.8818
LONDON +44 (0)20.8574.9700
NEW YORK +1 201.896.8600
BEIJING +86 10.8492.1587
CANADA +1 519.538.0888
ProPlex Floppy Drive DIN Rail-A full serviceA full service company providing technical support, customer service, and follow-up.
Providing products and services for the industrial, entertainment, installation, defense, broadcast, research, telecommunications, and signage industries.
Servicing the global market from offices in Los Angeles, London, New York, Toronto, and Beijing.

ProPlex FloppyDrive DIN Quick Start Guide, v1.2 14 June 2021

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals