REXING V1 Max Real 4K UHD Dash Camera with Wi-Fi and GPS User Guide
- June 6, 2024
- Rexing
Table of Contents
REXING V1 Max Real 4K UHD Dash Camera with Wi-Fi and GPS
Overview
Thank you for choosing REXING! We hope you love your new product as much as we
do.
If you need assistance, or have any suggestions to improve it, please contact
us. You can reach us via care@rexingusa.com or
call us at 203-800-4466. Our support
team will respond you as soon as possible.
Always a surprise in Rexing. Check us out here.
https://www.facebook.com/rexingusa/
https://www.instagram.com/rexingdashcam/
https://www.rexingusa.com/support/registration/
What’s in the box
- Rexing V1 Max Dashboard Camera
- Car Power Connector (12ft)
- 3M Adhesive Mount
- USB Cable
- User Manual
- Safety Guide
- Cable Management Tool
Camera Overview
- OK (Confirm) Button / Emergency Lock Button
- Up Navigation Button / Record Button*
- Power Button / Screen Toggle Button
- Down Navigation Button / Mic Button**
- Menu Button / Mode Button
- Micro SD Card Slot
- Reset Button
- USB Charging Port
- Rear Camera Port (Not Support)
- GPS Logger Port (Built-in GPS Logger)
The camera is recording when the LED is flashing red.
Screen Icons
Installation
Step 1: Install the Dash Cam
Place the 3M tape on the Mount and properly orient the Mount square to the roof and hood line of the vehicle. Important! Ensure the T-interlock on the Mount is oriented in the correct direction.
Firmly press the Mount onto the windshield. Wait at least 20 minutes before mounting the camera.
On the illustration Orient the mount as shown.
Step 2: Insert the Memory Card
The Rexing V1 Max accepts [Class 10/UHS-1 or higher] Micro SD memory cards up to 256GB. You will need to insert a memory card before you can begin recording. Before inserting or removing a memory card, first ensure you’ve powered down the device. Gently push the memory card in until you hear a click, and allow the spring release to push the card out.
Step 3: Power the Camera and Format the
Memory Card
Power the camera by connecting the charger to the car cigarette lighter and
camera. To ensure the V1 Max records to your memory card properly and without
error. Before you start using a new memory card, you must format the card
within the camera using the format function. Always backup important data
stored on the memory card before formatting.
To format the memory card, make sure you have inserted your memory card, then
turn on the device by connecting to a power source. Press REC to stop
recording. Then press the MENU button twice to enter the System Setup Menu.
Use the REC and MIC buttons and go to the Format setting. Press the OK button
to confirm the selection.
You may now disconnect from power. The camera will shut down after 3 seconds.
The camera should begin recording auto
matically the next time it is powered on.
Step 4: Installing the Camera onto the Windshield
Place the camera on the mount and carefully route the power cable around the
windscreen and tuck in under the trim.
Plug the Car Charger Cable into a 12V DC power outlet or the car cigarette
lighter.
Connect car charger to the camera. The camera will auto-start recording once
powered on.
Basic Operation
Device Power
The device is automatically powered on when plugged into a 12V accessory
socket or cigarette lighter and received a charge (i.e.: the vehicle is
started).
To turn the device on manually, press and hold the Power button until the
welcome screen appears.
The camera will automatically start recording when power on.
Menu Settings
Power the camera On. If the camera is recording, press the REC button to stop
recording.
Hold the MODE button and toggle to the desired mode. Press the MENU button
once to enter the settings menu for a Mode. Press the MENU button twice to
enter the System Settings (Set up).
Video Recording
The camera will automatically start recording when the device receives charge.
The LED lights and red dot will blink red device when recording. Press the REC
button to stop recording.
EMR Mode
To use the Emergency Record Mode, press the “OK/EMR” button to manually record
a 20 second video that is automatically saved and locked.
View EMR recordings by pressing the menu/playback button.
Video Playback
Playback of videos can be done on the device or a computer.
To playback a video on the device, toggle to the Playback mode. Use the REC
and MIC buttons to toggle to the desired video. Press the OK button to play.
During playback use the OK (pause), REC (rewind) and MIC (fast forward)
buttons to control the video playback.
To playback a video on the computer
either use an SD card adapter or connect the device to the computer directly
using the USB cable.
To playback a video using an SD card adapter,
remove the memory card and insert it into an SD card adapter. Place the
adapter in the computer.
To playback a video using USB cable,
connect the USB Cable to the device and the computer. After the device powers
up, press the OK Button to select Mass Storage.
On the computer, navigate to device drive. The videos are stored at: the
“Front_xxx” subfolders respectively. Locked videos can be found on the memory
card under the
“front_emr” folder.
Wi-Fi Connect
Download “Rexing Connect” app from the App Store/Google Play Store.
- To access or exit the Wi-Fi feature, press the menu button/playbackbutton twice to access system settings. Find “Wifi” from the list, tap OK Button , set the Wi-Fi feature “ON” and “OFF”. Find “SSID” from the system setting > About.
- Open Wi-Fi settings on your phone, find “SSID” from the list, tap to connect. (Default password: 12345678)
- Open the Rexing Connect app, tap “Connect” to enter the realtime video streaming page.
- Once connected, the dash cam screen will switch to the camera view and will display “WiFi Connected” message. Using the Rexing Connect app, you can view a live preview of the dash cam screen, start / stop recording, as well as view and save your captures with your mobile device.
For further instruction regarding the Wi-Fi Connect feature, please visit www.rexingusa.com/wii-connect/.
GPS Logger
When connected to the camera, it will record the speed and location of your
vehicle as you drive.
You can then access this information while playing back your recordings using
the GPS Video player (For windows and Mac, available at rexingusa.com).
The dash cam will automatically search for the GPS signal once it’s connected
to the power source. Press the MENU button twice and go to System Settings.
Toggle the GPS Speed Unit setting, and select your favorite speed unit.
After a GPS signal is found, the screen icon will turn from not connected to
active – as per the below icons.
Parking Monitor
Connect the dash cam to the Smart Hardwire Kit (need to purchase separately)
to activate the parking monitor function. Please visit
www.support.rexingusa.com to watch a video tutorial.
Taking Photos
To take a photo, stop video recording and hold down the REC button.
To view a photo, stop video recording and hold on MENU button to the
Playback Mode.
Press the REC and MIC Buttons to toggle through your photos.
To delete a photo, stop video recording and toggle to the Playback Mode and
toggle through the videos and photos to the one you want to delete.
Hold the MENU to toggle the Delete option.
Press the OK Button and select Delete Current or Delete All.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>