Klim 34462034 Tempest Laptop Cooler With Vacuum Fan User Manual

: June 6, 2024
: KLIM

Table of Contents

Introduction
Product description
Assembly and installation
Operating the cooler
Troubleshooting & Contact
Technical specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Klim 34462034 Tempest Laptop Cooler With Vacuum Fan User Manual

Introduction

On behalf of the entire KLIM Team, we thank you for purchasing our KLIM Tempest laptop cooler. We hope it meets your expectations and that you enjoy using this device.

KLIM Tempest is a new generation cooling system especially designed to solve overheating problems in laptops. Please read these instructions carefully because proper installation is essential so that the product works effectively. If you have any questions about installation or compatibility, reach out to support@klimtechnologies.com.
We always answer within 24 hours and will be glad to assist you!

Product description

Connecting plate lock
Metal connecting plate
3M fixing adhesive
Digital display
Speed –
ON/M button
Speed +
Exhaust port
Power port
Clamp arm
Plastic connecting plate (with suction pads)
Rubber sleeve
Suction port

Assembly and installation

Attach a connecting plate (plastic or metal, according to your needs) to the main body by inserting the round hole in the connecting plate lock.

Note: to release the plate, press the lock and slide the plate towards the back of the main body.

Adjust the metal plate length by pushing the moving part.
Optionally, you can remove the 3M glue tape to fix it in a more permanent position.

Hint: check that the plate or suction pads aren’t blocking any air exhausts under your computer.

Select a rubber sleeve that fully covers your laptop’s exhaust port and attach the sleeve to the suction port on the KLIM Tempest.

Place the suction port with the sleeve against your laptop’s exhaust port, ensuring a proper seal.

Turn the clamp arms until they are facing forward and lift them above the computer to fix the cooler in place. The computer thickness must be between 13 and 27 mm for this attachment system to work.

Metal plate connection
Attachment to exhaust vent

Operating the cooler

Connect the laptop cooler to your computer using the supplied USB cable.

Automatic mode

Press the ON/M button to turn on the KLIM Tempest. The device enters Automatic Mode (AT) by default. In this mode, it automatically detects the air temperature coming off your computer and adjust the fan speed automatically. The cooler switches off when temperature is lower than 35 °C and works at full capacity when it reaches 50 °C.

Note: press and hold the ON/M button to switch the display mode between Fahrenheit and Celsius.

Manual mode

Press the ON/M button while in Automatic Mode to switch to Manual Mode (MT). The default fan speed is 7 (out of 13 levels).
Press the + / – buttons to adjust the fan speed. The LCD display briefly shows the speed level while adjusting it.

Hint: adjust the fan speed to find the perfect balance between noise and cooling.

Shutdown

Press the ON/M button while in Manual mode to switch off the cooler.

Troubleshooting & Contact

If you ever encounter any problems with the laptop cooler, remember that your product is covered by our warranty. We also remain at your disposal to help you with any issues.
Do not hesitate to contact us at support@klimtechnologies.com for additional support.

Q: The device makes too much noise

A: This can be normal in cases of excessive temperature (where the fan is spinning at maximum speed). If you hear any rattling sounds, a foreign object may have been lodged inside the product. Please contact us so we can help you solve this issue.

Q: The laptop cooler does not turn on

A: Check that the cable is in good condition and connected properly. If available, you can try on a different port on your computer, or with another compatible cable.

Q: The cooler turns on but the fan does not start

A: This can be normal if the device is in automatic mode (AT) and not detecting high temperature. Press the ON/M button to enter Manual mode (MT) and select your desired speed using the + and – buttons. If the fan does not work in Manual Mode, please contact us.