avenli 290729US Sand Filter Pump Instructions
- June 6, 2024
- avenli
Table of Contents
Avenli 290729US Sand Filter Pump Manual
SFP6-20-GB
Product specifications
Safety instructions
Always follow the basic safety precautions for installation and use of this electrical equipment, including
WARNING: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
WARNING: Children being supervised not to play with the appliance
WARNING: The product should be away from the product, so as to avoid children climbing into it.
WARNING: There is risk of electric shock. This product is only connected to the outlet with grounding protection. If it can not be confirmed, please contact an experienced electrician for installation, this outlet has a maximum leakage current of up to 30mA.; please do not use the movable outlet.
WARNING: The pump is to be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.
WARNING: To remove this product, before cleaning, maintenance or adjustment, unplug the power plug from the outlet.
WARNING: Do not bury the wire in the soil, and must arrange it on safety location where it can not be damaged by the lawn mower and other equipment.
WARNING: The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped.
WARNING: To reduce the risk of electric shock, do not connect any extension wire, timer, plug adapter or converter to the filter body. Please provide a fixed outlet.
WARNING: If you stand in a place with water or your hands are wet, do not unplug the power wire plug.
WARNING: After this product is installed, the installation position of the plug should be visible to the user and easy to access.
WARNING: When the product is in use, do not start this product.
WARNING: Only adult can install and remove this product.
WARNING: This product can only be used with a movable product. Do not use it in conjunction with a fixed product. The movable product can be removed for water storage and re-installed on its original position.
WARNING: To avoid damage to the product and the risk of injury, before the rotating the control valve position, please turn off the product.
WARNING: To reduce the risk of being absorbed, if the filter cover is loosened, damaged, destroyed, or lost, do not put it into the product. In case of the above conditions, please replace the filter cover immediately.
WARNING: Do not play or swim near the filter cover. Your body or hair may be inhaled to cause permanent injury to the body or drowning.
WARNING: When the reading displayed on the pressure gauge of the body exceeds a predetermined maximum data, do not start this product.
WARNING: There is a risk of pressure; any improper installation of the cylinder head can cause its damage, resulting in serious injury, death or damage to any property.
NOTE: this product is limited to those purposes described in the specification.
WARNING:The maximum total head:1.5m.
Note: During the operation of the sand filter pump, check the pressure reading of the manometer.
Generally, when the pressure of the recommended sand filter pump is less than 0.2bar (3psi) (green area) , it runs normally. Note: You must make sure that maintenance begins only after the sand filter pump is unplugged. Otherwise serious risks such as personal injury and even death may occur. Note: Record the reading of the manometer during the operation of the sand filt er pump. When the manometer shows a pressure of 0.2bar (3psi) or higher, please clean up the sand bend or replace the sand. Use “backwash” and “rinse” functions.
Note: regular rinsing according to use situation is recommended.
Long-term storage and storage in winter
Using the product in a frozen pool may damage the product and invalidate the quality warranty. If the product has to be used with antifreeze, propylene glycol may also be used. Propylene glycol is a nontoxic chemical unharmful to any plastic parts. Other types of antifreeze are highly toxic and may be harmful to the product’s plastic elements.
-
Before discharging the water or repostioning of the pool, make sure the discharge direction is towards the discharging ditch and away from the home. Review local regulations for special water treatment requirements.
-
Switch off the product and remove the power plug.
-
After emptying, remove all connected sand filter pumps, corrugated tubes and filter hoods on the pool wall.
-
Unscrew the drain valve (8) in an anticlockwise direction to completely empty water inside the body. The drain plug is at the bottom of the body.
-
Dry the parts of the sand filter pump and corrugated tubes.
-
Lubricate the seal rings and washers in the order below for long-term storage.
-
The best practice for product storage is to dry the parts and motor and replace them in the original package. To avoid shrinkage or corrosion, do not cover or wrap the motor with a plastic bag.
-
Please store the motor and parts in a dry place at 32°F (0°C) ~104°F (40°C).
Diagnosis of Problems and Solutions
