ADEPT INDUSTRIES V2 Club Booster Remote User Manual
- June 5, 2024
- ADEPT INDUSTRIES
Table of Contents
ADEPT INDUSTRIES V2 Club Booster Remote
Introduction
Speed Control – Press “C.” [Go/Speed Up] button to move forward. Your
Club Booster has 6 speeds and defaults to Speed 1 each time you stop, for
safety. Cycle through speeds by pressing Go/Speed Up and Reverse/Slow Down;
each time you press Up or Down, the speed changes. Reverse/Slow Down – Press
and hold the “4 ” [Reverse/Slow Down] button at stationary to reverse. Release
the button and the unit will gradually stop. Left/Right turn – Press and hold
the “t” [Left] or “f” [Right] buttons to turn left or right. Slow to Speed 1
or Speed 2 to turn a fixed-front wheel cart.
Stop – Press the “0” [Stop] button to bring your Club Booster to a
gradual stop. 15-Yard/30-Ya『d Presets – Press “0” or “G” button and your cart
will travel
those preset yardages. You are able to steer your cart while in Preset Mode.
Free-Wheel Mode -You can free-wheel to push your cart by holding down the Stop
button for 3 seconds. The red light on the Club Booster console will flash.
Press any button to exit Free-Wheel Mode.
Gyro On/Off – Press “0” [Gyro] button to deactivate the gyro. The yellow
light on the Club Booster console will turn off. Turn off the gyro when you
are using your Club Booster for power-assist, when walking with the unit and
steering manually. Keypad Lock – Press the “(!)” [Keypad Lock] button to lock
the keypad so buttons are not accidently activated. The red light on the
remote will flash. Press the Keypad Lock button and any other button within 3
seconds to exit Lock Mode. Charging The Remote – Charge the remote by plugging
the micro USB cable (included) into the remote and any USB charging inlet.
Pairing The Remote – The remote is paired to your Club Booster at the factory.
If your unit loses pairing to the remote, use the following procedure: 1) Turn
off the Club Booster, 2) Press and hold both the “Stop” and “30-Yard” buttons
until the light in the upper corner flashes, 3) Turn on the Club Booster, 4)
Release the “Stop” and “30” buttons. The remote is paired when the red light
stops flashing.
This device complies with Industry Canada licence-exempt RSS standard( s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.”
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>