techtop SPL 54 Stage Light User Manual

SPL 54 Stage Light

User Manual

Safety Instructions

CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
For your own safety, please read this user manual carefully before you initial start-up.

Features:

SPL 54: STAGE LIGHT is one of the classical LED fixtures designed and created uniquely, really ideal for theaters, churches, TV studios, photography studios, fashion shows, stage performances, musical shows, etc.

• Power in powerCON/blue, Power out powerCON/grey equipped;
• LED display;
• New PWM dimming electronic theory applied for reasonable fresh rates and real flicker free;
• Molded aluminum for excellent ventilation, no need of fans, no noise;
• Driving IC and capacitors from USA and European unions equipped for steady constant current outputs;
• Intelligent temperature self controlling: self adjusting temperature to protect at the time of max. temperature happening;

Installations:

Regardless the rigging point you choose for your fixture, always be sure to secure the fixture with a safety rope which sold separately.

DMX-512 Connection / Connection Between Fixtures

Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX- output of the controller directly with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter-cables.

Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX- input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected.

Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.

Connection with the mains
Connect the device to the mains with the enclosed power supply cable.

1. DMX 512 protocol

Addressing
The LED DISPLAY on the rear side of the base allows you to assign the DMX fixture address, which is defined as the first channel from which the item will respond to the controller. If you set, for example, the address to channel 7, the item will use the channel 7 to 14 for control.

Please, be sure that you don’t have any overlapping channels in order to control each item correctly and independently from any other fixture on the DMX data link. If two, three or more items are addressed similarly, they will work similarly. At DMX mode you can choose the address from 1 to 512.After you connect the item to the mains, the item starts running. When the item finishes resetting, A-OO1 will flash in the led display and then set the desired DMX address by pressing the UP or DOWN buttons.

DMX Controlling:
After having addressed all items, you may now start operating these via your lighting controller.
After switching on, the item will automatically detect whether DMX 512 data is received or not.

DMX Functions

9-CHANNEL MODE
Channel 1 – red from darkness to full brightness
Channel 2 – green from darkness to full brightness
Channel 3 –blue from darkness to full brightness
Channel 4 – white from darkness to full brightness
Channel 5 – master dimmer from darkness to full brightness
Channel 6 –strobe
Channel 7 –color macros
Channel 8 – color changing
Channel 9 – color fades

5-CHANNEL MODE
Channel 1 – red from darkness to full brightness
Channel 2 – green from darkness to full brightness
Channel 3 –blue from darkness to full brightness
Channel 4 – white from darkness to full brightness
Channel 5 – master dimmer from darkness to full brightness

6-CHANNEL MODE
Channel 1 – red from darkness to full brightness
Channel 2 – green from darkness to full brightness
Channel 3 –blue from darkness to full brightness
Channel 4 – strobe
Channel 5 – white from darkness to full brightness
Channel 6 – master dimmer from darkness to full brightness

2. Auto

Press the MODE button, the following functions can be achieved by the button ENTER:
SH01-03:: run the preset shows；
SP01-10: running the preset shows speed adjustments

3. Sound active

Press the MODE button, till SOUND appears, press UP or DOWN, SOUND ON,SOUND OFF, display, confirm SOUND ON by the button ENTER, the item will run to the beat of music, the sound active sensitivity can be adjusted from SENS 001 smallest to SENS 010 biggest

4. Synchronization & master /slave mode

Take one item and set the item at auto or sound active as above,then get other items and press the button MODE, set at SLAVE, confirm by the button of ENTER, then connect the items at SLAVE to the item at AUTO or sound active, disconnect the items from DMX controller, the items will work simultaneously. The item at auto or sound active works as master, others as slave.

LED Display Control:

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Before replacing the fuse, unplug mains lead.

Procedure:
Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.

Technical Specifications

One of the classical LED fixtures designed and created uniquely, really ideal for theaters, churches, TV studios, photography studios, fashion shows, stage performances, musical shows,etc.

• Power in powerCON/blue, Power out powerCON/grey equipped;

• LED display;

• new PWM dimming electronic theory applied for reasonable fresh rates and real flicker free;

• molded aluminium for excellent ventilation, no need of fans, no noise;

• driving IC and capacitors from USA and European unions equipped for steady constant current outputs;

• intelligent temperature self controlling: self adjusting temperature to protect at the time of max. temperature happening;

• Equipped with 54*high MCD 3W LED,RED/GREEN/BLUE/WHITE, each 12/14/14/14 pcs,

• total max. 162W, 50,000 hours
  AC 100-240V 50/60Hz

• Power consumption: max. 170W

• beam angle 25°
  0-100% linear dimming, separate strobe
  DMX 512 protocol, master/slave, auto, sound active with adjustable sound sensitivity
  9/5/6 DMX channel modes
  Running temperature self controlling
  Displaying off 5 seconds automatically after finishing sets of the fixture

• Environmental temperature: -20℃ to 40℃

• Hanging brackets included: floor stand

• Net weight:2.65kgs

• Dimensions: 28080270mm(LWD)(hanging bracket placed vertically)

• Please note: Every information is subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>