techtop FOGGER V9 Stage Fog Machine User Manual
- June 6, 2024
- techtop
Table of Contents
techtop FOGGER V9 Stage Fog Machine
CAUTION
-
Keep this device away from rain and moisture
-
Unplug mains lead before opening the housing
-
Make sure of the voltage on your end suitable for the unit
For your own safety, please read this user manual carefully before you initially start-up. Every person involved with the installation, operation and maintenance of this device has to -
be qualified
-
follow the instructions of this manual
INTRODUCTION
Thank you for having chosen club smoke DMX series. You will see you acquired a powerful and versatile device. Unpack your item. Before you initial start-up, please make sure that there is no damage caused by transportation. Should there be any, consult your dealer and do not use the device.
SAFETY INSTRUCTIONS
If the device has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation
water might damage your device. Leave the device switched off until it has
reached room temperature. Always plug in the power plug least. Make sure that
the power switch is set to OFF position before you connect the device to the
mains. Never let the power cord come into contact with other cables! Handle
the power cord and all connections with the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear
panel. Make sure that the power cord is never crimped or damaged by sharp
edges. Check the device and the power cord from time to time.
CAUTION! Before filling the machine disconnect from mains. Never drink
fluid or use it on the inside or outside of a human body. If fluid gets in
contact with skin or eyes, rinse thoroughly with water. If it is necessary
call a doctor immediately!
DANGER OF EXPLOSION! Never add flammable liquids of any kind to the fog
liquid. Keep device upright. Never aim the output nozzle directly at people or
at open flames.
DANGER OF BURNING! Keep minimum distance of 50 cm to nozzle! Always
disconnect from the mains, when the device is not in use or before cleaning
it. Only handle the power cord by the plug. Never pull out the plug by tugging
the power cord. Keep away children and amateurs!
Never leave this device running unattended.
FEATURES
- Ideal for party-rooms or small discotheques,
- Powerful output,
- With remote control,
- Quality thermostat,
- Overheat protective switch,
- Constant and steady output fog;
STARTING OPERATION
-
ON/OFF control
Connect the remote control box to the 5-pin socket on the rear of the fogger and then you can press the button on the box to on/off emit the fog. After a certain warm-up time, the device is ready to operate. Upon warming up, the stand-by lamp, red LED, of the remote control lights up. When the geen led lights up, the fogger is ready to emit and by switching the control box the fogger starts emission. The temperature is regulated by a high quality thermostat. -
Wireless remote control
Connect the remote control box/receiver to the 5-pin socket on the rear of the fogger and then you can use the wireless launcher to on/off emit the fog. The dip switches on the remote receivers of foggers can be set to the same addressing and then the foggers can be controlled symtaneously by the remote launcher.
CAUTION: The escape nozzle will heat up during operation. Therefore do not touch the nozzle until it has cooled down completely.
Cleaning the heating element
The heating element should regularly be cleaned every 30 operational hours in
order to avoid clogging. Use haze machine cleaner available at your dealer.
Procedure:
Fill cleaner into empty tank. Run the machine several times in a well-
ventilated room only. The number of repetitions depends on the pollution level
of the vaporizing elements. After use clean all remaining cleaner and rinse
the tank thoroughly. There are no serviceable parts inside the device except
for the fuse. Maintenance and service operations are only to be carried out by
authorized dealers.
Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of
same type and rating. Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Open the fuse holder on the rear panel with a fitting
screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.
Should you need any spare parts, please use genuine parts.
If the power supply cable of this device will be damaged, it has to be
replaced by a special power supply cable available at your dealer. If
defective, please dispose of the unusable device in accordance with the
current legal regulations. Should you have further questions, please contact
your dealer.
TECHNICAL SPECIFICATIONS
Power supply: 230 V AC, 50 Hz
Fuse: 250V 5A
Power consumption: max.900 W
Warm-up time: approx. 5 min.
Fog output: 4500 cuft/min
Tank capacity: 1.3L
Dimension: 250250175mm
Weight: 3.60kgs
Please note: Every information is subject to change without prior notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>