techtop LED Beam 7 Zoom User Manual
- June 6, 2024
- techtop
Table of Contents
techtop LED Beam 7 Zoom
SAFETY INSTRUCTIONS
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a
dangerous electric shock when touching the wires!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
For your own safety, please read this user manual carefully before you initial
start-up.
Features:
15°-67° zooming,with 7*high MCD Ostar RGBW 4 IN 1 15W LEDs
DMX-512 connection / connection between fixtures
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-
output of the controller directly with the DMX-input of the first fixture in
the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs,
you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-
input of the next fixture. Always connect one output with the input of the
next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a
terminator. Solder a 120 resistor between Signal (–) and Signal (+) into a
3-pin XLR-plug and plug it in the
DMX-output of the last fixture.
Connection with the mains
Connect the device to the mains with the enclosed power supply cable.
1. DMX 512 protocol
Addressing
The LED DISPLAY on the rear side of the base allows you to assign the DMX
fixture address, which is defined as the first channel from which the item
will respond to the controller. If you set, for example, the address to
channel 7, the item will use the channel 7 to 14 for control. Please, be sure
that you don’t have any overlapping channels in order to control each item
correctly and independently from any other fixture on the DMX data link. If
two, three or more items are addressed similarly, they will work similarly. At
DMX mode you can choose the address from 1 to 512.After you connect the item
to the mains, the item starts running. When the item finishes resetting, A-OO1
will flash in the led display and then set the desired DMX address by pressing
the UP or DOWN buttons.
DMX Controlling:
After having addressed all items, you may now start operating these via your
lighting controller. After switching on, the item will automatically detect
whether DMX 512 data is received or not.
DMX FUNCTIONS
16-channel mode
| 1 | 000 – 255 | X |
|---|---|---|
| 2 | 000 – 255 | X-Fine |
| 3 | 000 – 255 | Y |
| 4 | 000 – 255 | Y-Fine |
| 5 | 000 – 255 | XY SPEED |
| 6 | 000 – 255 | Dimmer(0-100%) |
7
| 000 – 009| Shutter closed
010 – 245| Strobe effect slow to fast
246 – 255| Shutter open
8| 000 – 255| Red
9| 000 – 255| Green
10| 000 – 255| Blue
11| 000 – 255| White
12| 000 – 255| Color Temp
13
| 000 – 010| closed
011 – 020| R
021 – 030| G
031 – 040| B
041 – 050| W
051 – 060| R+G
061 – 070| G+B
071 – 080| B+W
081 – 090| R+B
091 – 100| G+W
101 – 110| R+W
111 – 120| R+G+B
121 – 130| R+G+W
131 – 140| G+B+W
141 – 150| RGBW
151 – 255
| Color changing from slow to
fast
14| 000 -255| Color fade from slow to fast
15
| 000 – 020| Empty
021 – 040| Internal program 1
041 – 060| Internal program 2
| 061 – 080| Internal program 3
---|---|---
081 – 100| Internal program 4
101 – 120| Internal program 5
121 – 140| Internal program 6
141 – 160| Internal program 7
161 – 180| Internal program 8
181 – 200| Empty
201 – 225| Motor Reset
226 – 255| Empty
16| 0-255| Focus from smallest to biggest
LED DISPLAY CONTROL:
1 Addr| DMX Address| 001-512|
---|---|---|---
2 ChMd| DMX Mode| .=CH16|
3 SPMd| Speed Mode| .=High|
| | .=Low|
4 SLMd| Run Mode| .=Master|
| | .=Slave|
5 SHMd
| Internal
Program
| ****
.=001
|
| | .=002|
| | .=003|
| | .=004|
| | .=005|
| | .=006|
| | .=007|
| | .=008|
6 Soun| ****
Sound Control
| ****
.=OFF
|
| | .=ON|
7 PAN| X Reverse| .=OFF|
| | .=ON|
8 TIL| Y Reverse| .=OFF|
| | .=ON|
9 dISP
| Display
Reverse
| ****
.=OFF
|
| | .=ON|
10 rFAC| Reset Default| .=OFF|
---|---|---|---
| | .=ON|
11 Ad t
| Home Position
Setting
| ****
Delt
| Clear PAN and TILT Home
Position(3s)
| | P(PAN)| .=0-120
| | t(TILT)| .=0-120
| | F(Gobo)| .=0-120
12 rST| Reset Motor| |
Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of
same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Open the fuse holder on the rear panel with a fitting
screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.
TECHNICAL SPECIFICATIONS
LED MINI-B 715 is one of the classical LED moving beam
designed and created uniquely, really ideal for clubs, bars,
disco halls, small events, musical shops, mobile DJs, cabarets, etc.
- 15°-67° zooming,with 7*high MCD Ostar RGBW 4 IN 1 15W LEDs
- LED Display,RGBW color mixing,multi color beams projecting sharply AC 100-240V 50/60Hz,Power consumption: 120W max.
separate strobe,strobe Rate: 0 to 30 Hz
DMX 512 protocol, master/slave, auto, sound active
16 DMX channel modes
Movement:Pan:X axis 540 degrees, Y axis 270 degrees
High speed of pan/tilt movement,
speed of pan/tilt movement adjustable
Scan position memory, auto repositioning after unexpected movement 8 internal program , sound mode can control by DXM 512 Environmental temperature: -20℃ to 40℃
Hanging brackets included
Net weight: 4.20Kgs,Dimensions:150200300mm(LWD)
Please note: Every information is subject to change without prior notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>