SONY CFI-2016 Slim Edition Gaming Console User Guide

SONY CFI-2016 Slim Edition Gaming Console User Guide

Health and Safety

Before using this product, carefully read this manual and retain it for future reference Parents and guardians of children should read this manual and make sure that children follow all safety precautions This product has been designed with the highest concern for safety However, any electrical device, if used improperly, has the potential for causing fire, electrical shock or personal injury Observe all warnings, precautions, and instructions Stop use and disconnect the AC power cord immediately if the product functions in an abnormal manner, produces unusual sounds or smells or becomes too hot to touch

⚠ WARNING ELECTRICAL SHOCK
To avoid electrical shock, do not open the enclosure Refer servicing to qualified personnel only

LASER (Only for consoles with a disc drive installed)
This appliance is classified as a CLASS 1 LASER product under IEC60825-1:2014 CONSUMER LASER PRODUCT EN 50689:2021

Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure The use of optical instruments with this product will increase eye hazard

MOVING FAN BLADES Keep body parts away from fan blades

SEIZURES INDUCED BY LIGHT STIMULATION (PHOTOSENSITIVE EPILEPSY) If you have an epileptic condition or have had seizures, consult your doctor prior to using this console Some individuals are sensitive to flashing or flickering lights or geometric shapes and patterns, may have an undetected epileptic condition and may experience epileptic seizures when playing videogames or watching video content

DISCONTINUE USE IMMEDIATELY and consult your doctor if you experience any of the following health problems or symptoms when exposed to flashing or flickering lights or other light stimulation whilst playing video games or watching video content: eye soreness, altered vision, migraine, muscle twitching, convulsion or other involuntary movements, blackout, loss of awareness, confusion, or disorientation

In addition to the above, DISCONTINUE USE IMMEDIATELY when you experience any of the following symptoms: headache, dizziness, nausea, fatigue, similar symptoms to motion sickness, or discomfort or pain in any body part such as eyes, ears, hands, arms, or feet whilst playing If the condition persists, seek medical attention

RADIO WAVES
Radio waves may affect electronic equipment or medical devices (for example, pacemakers), which may cause malfunctions and possible injuries

• If you use a pacemaker or other medical device, consult your doctor or the manufacturer of your medical device before using the wireless networking feature (Bluetooth® and wireless LAN)
• Do not use the wireless networking feature in the following locations:
  -­ Areas where wireless network use is prohibited, such as in hospitals Abide by medical institution regulations when using the console on their premises
  -­ Areas near fire alarms, automatic doors and other types of automated equipment

MAGNETS AND MEDICAL DEVICES
These products have magnets which may interfere with pacemakers, defibrillators and programmable shunt valves or other medical devices Do not place these products close to such medical devices or persons who use such medical devices Consult your doctor before using these products if you use such medical devices

VOLUME LEVEL
Permanent hearing loss may occur if headsets or headphones are used at high volume Set the volume to a safe level Over time, increasingly loud audio may start to sound normal but can actually be damaging your hearing If you experience ringing, discomfort in your ears or muffled speech, stop listening and have your hearing checked The louder the volume, the sooner your hearing could be affected To protect your hearing:

• Limit the amount of time you use the headset or headphones at high volume
• Avoid raising the volume to block out noisy surroundings
• Lower the volume if you can’t hear people speaking near you

LITHIUM BATTERIES
WARNING: This console contains a lithium button / coin cell battery

• The battery is hazardous New or used batteries should be kept out of reach of children
• If swallowed or placed inside any part of the body the lithium button cell battery can cause severe or fatal injuries in 2 hours or less
• If you think the battery may have been swallowed or placed inside any part of the body, you must seek immediate medical attention

Do not handle damaged or leaking lithium-ion batteries If the internal battery fluid leaks, stop using the product immediately and contact technical support for assistance If the fluid gets on to your clothes, skin or into your eyes, immediately rinse the affected area with clean water and consult your doctor The battery fluid can cause blindness
The controller contains a lithium-ion rechargeable battery
Do not allow the battery to come into contact with fire or subject it to extreme temperatures such as in direct sunlight, in a vehicle exposed to the sun or near a heat source Never attempt to open, crush, heat, or set fire to the controller or the battery Do not leave the battery charging for a prolonged period of time when the controller is not in use

YOUNG CHILDREN INJURIES
Keep the product out of the reach of young children Young children may swallow small parts, pull on cables and cause the console or the controller to fall, or wrap the cables around themselves, which may inflict injury or cause an accident or a malfunction

NEVER DISASSEMBLE OR MODIFY THE PRODUCT OR ACCESSORIES There is a risk of fire, electric shock, or injury

⚠ Precautions
Use of the AC power cord
Stop use, unplug the AC power cord from the electricity supply and disconnect any other cables immediately if the device functions in an abnormal manner, produces unusual sounds or smells or becomes too hot to touch

Well-lit area Use in a well-lit area and keep a safe distance from the TV screen

Taking breaks

• Avoid prolonged continuous use of this product Generally we recommend that you take 15-minute breaks for every hour of play
• Avoid playing when you are tired or need sleep
• Stop using the console immediately if you begin to feel tired or if you experience discomfort or pain in your hands or arms while operating the controller If the condition persists, consult a doctor
• If you experience any of the following health problems, discontinue use of the console immediately If symptoms persist, consult a doctor ­ Dizziness, nausea, fatigue or symptoms similar to motion sickness ­ Discomfort or pain in a part of the body, such as eyes, ears, hands or arms

Vibration function

• If the controller is sitting on a flat surface, the vibration of the controller during gameplay may cause it to fall, leading to injury or malfunction
• Do not use the vibration or trigger effect function if you have any ailment or injury to body parts such as the bones, joints, or muscles of the hand or arm or that may be affected by this vibration function To disable the features, select Settings ⚙ > Accessories from the home screen

Static shock
When using a headset or headphones in particularly dry air conditions, you may sometimes experience a small and quick (static) shock on your ears This is a result of static electricity accumulated in the body, and is not a malfunction of your headset or headphones This effect could be reduced by wearing clothes made from materials that do not easily generate static shock

Moisture condensation
If the console is brought directly from a cold location to a warm one, moisture may condense inside the console Should this occur, the console may not operate properly In this case, turn off and unplug the console until the moisture evaporates (this may take several hours) If the console still does not operate properly, contact the appropriate PlayStation® customer service helpline which can be found within the guarantee section

High temperature message
If the console becomes too hot, you will see a notification message on your screen Continued use while the message displays may lead to the console becoming non-operational If you see the message, turn off the console and wait until it cools down After the console cools down, move it to a well-ventilated location that is not subject to high temperatures Check to make sure the console vents are not blocked, and if you installed an M2 SSD to the console, be sure that the heat-dissipation parts haven’t detached from the M2 SSD See “Install an M2 SSD” (page 8) for more information on heat-dissipation parts

Motion sensor
When using the motion sensor function of the controller, be cautious of the following points If the controller hits a person or object, it may cause accidental injury or damage

• Before using the motion sensor function, make sure you have enough space to move around
• Firmly grip the controller to prevent it from slipping out of your grasp and causing damage or injury
• If using a controller that is connected to the PS5® console with a USB cable, make sure there is enough space for the cable so that the cable will not hit a person or object

Light bar
Do not stare at the light bar on the controller when it is blinking Stop using the controller immediately if you experience any discomfort or pain

Liquid, dust, smoke, steam, and heat

• Always ensure the product and its connectors are free of liquid, excess dust and small particles
• Do not leave the product in the following areas during use, storage, or transportation
  – Areas exposed to smoke or steam
  – Areas with high humidity, dust, or cigarette smoke
  – Areas near heating appliances, areas exposed to direct sunlight, or areas that retain heat

AC power cord and cables

• Do not use the cord or cables if they are damaged or modified.
• Do not use a power cord other than the included AC power cord. The AC power cord is designed specifically for use with this console only, and should not be used with other electrical devices.
• Do not touch the plug or connector with wet hands.
• Do not walk on the cord or cables or pinch them, particularly at plugs, receptacles, connectors and where they exit from the console.
• Do not expose the cord or cables to heat or place them near heating appliances.
• Do not place heavy items on the cord or cables.
• Do not pull or bend the cord or cables with excessive force.
• Do not connect the AC power cord to a voltage transformer or inverter. Connecting the cord to a voltage transformer for overseas travel or an inverter for use in a vehicle may cause it to heat up in the console and may cause burns or a malfunction.
• Before connecting or plugging in the AC power cord, check that there is no dust or small particles in or on the plug or connectors or the AC IN connector on the console.
• Unplug the cord and cables if you want to clean or move your console or do not intend to use it for an extended period of time. When disconnecting, hold the cord by the plug and pull straight out of the socket. Never pull by the cord and do not pull out at an angle.

Set up and handling

• Do not use the console in a closed cabinet or other locations where heat may build up. Doing so may cause the console to overheat and may lead to fire, injury or malfunction.

• Do not touch product during an electrical storm.

• Do not expose the console, accessories or battery to high temperatures, high humidity or direct sunlight during operation, transportation and storage.

• Do not place the console or accessories on surfaces that are unstable, tilted or subject to vibration.

• Use the included horizontal stand feet to set the console in the horizontal position.
  If you do not use the feet and set the console in a position other than instructed, there is a risk of injury, damage, or malfunction. For instructions on attaching the feet, please see the Quick Start Guide. To set the console in the vertical position, you’ll need to use the vertical stand (sold separately).

• When setting up or carrying the console, be careful to securely hold the main body of the console Do not hold, carry, or lift the console by only the cover; doing so could cause the cover to detach and the console to fall, leading to potential injury or damage

• Do not move the console or adjust its position when the power indicator is lit or blinking Data may be lost or corrupted, or the console may be damaged

• Do not stand on or put objects on the console, and do not stack the console with other devices

• Do not place the console and connected accessories on the floor or in a place where they may cause someone to trip or stumble.

• Do not touch the connectors of the console or accessories.

• Do not allow bodily contact with the console or air from the console vents for an extended period of time while in use. Extended contact under these conditions may cause low-temperature burns.

• The console should be installed and operated with a minimum distance of 20 cm away from your body.

• Do not use the product near water.

• Do not move or change the position of the console with a disc inserted.
  The vibration may result in scratching of the disc or the console.

Power off

• Do not turn off the console while data is being saved on or loaded from the SSD or USB drives
• Do not remove the AC power cord from the electricity supply until the power indicator has turned off If you disconnect the AC power cord while the power indicator is lit or blinking, data may be lost or corrupted, or the console may be damaged

Use of the cover

Do not use the console without the cover. Doing so may cause fire, electrical shock, or malfunction. Do not remove the cover of the console immediately after use. The main unit of your PS5 console may still be hot immediately after use, and continued handling
with the cover off may cause burns. If you need to remove the cover, turn off your PS5 console, unplug the AC power cord and cables, and wait for it to cool down.

Compatibility
Controllers intended for use with PlayStation®, PlayStation®2, and PlayStation®3 consoles, such as the analogue controllers (DUALSHOCK® and DUALSHOCK®2) and the DUALSHOCK®3 wireless controller, are not compatible with the PS5 console.
The DUALSHOCK®4 wireless controller is compatible with PlayStation®4 format software on the PS5 console, but not with PS5 format software on the PS5 console.

Safe use for children
Parents are encouraged to monitor children in online activities to ensure safe and responsible internet usage. Refer to playstation.com/safety for further details.

Remove and attach covers

Remove the covers when performing maintenance on your console, or when installing an M2 SSD or disc drive.

Safety warnings
Before removing or attaching the covers, please read the following safety precautions

⚠ Caution

• Keep out of reach of young children Young children may swallow small parts which may inflict injury
• After you have turned off your PS5 console and unplugged the AC power cord and cables, wait for your console to cool down before removing and attaching the covers The main unit of your PS5 console may still be hot immediately after use, and continued handling of your console may cause burns
• Be careful not to pinch your fingers in the gaps between parts, and not to hurt your hands and fingers on the corner of parts
• When turning on your console, make sure the covers are installed correctly If the covers are not installed correctly, it may cause the main unit to overheat.

Remove and attach covers
Place your console on a soft cloth spread over a flat surface before removing or attaching the covers Illustrations show the console with disc drive installed

1. Go to the control centre and select Power > Turn Off PS5.
   The screen goes blank, the power indicator flashes white, and then turns off.

2. Remove the AC power cord and cables, and then wait for the PS5 console to cool down.
   The main unit of your console is hot immediately after use.

3. Place the console with the bottom facing up and the front side facing you, and then remove the feet.

4. Remove the cover.
   Slightly lift the cover away from the console to detach its clips and remove it.

5. Attach the cover.
   Align the cover’s clips with the corresponding holes on the console and push in until you hear a “click”.

6. Attach the feet, connect the AC power cord and cables, and then turn on the power.

Install an M.2 SSD

M2 SSD is storage that uses flash memory Install a commercially available M2 SSD in your PS5 console for more storage for your game and app data

Types of M.2 SSD
You can use an M2 SSD with the following specifications:

Notices

• Both single-sided devices and double-sided devices are supported
• M2 SATA SSD is not supported
• Allocation of host memory to HMB (Host Memory Buffer) supported devices is not supported
• Carefully review drive specifications prior to purchase and contact the vendor or manufacturer if you need further information SIE cannot guarantee that all M2 SSD devices meeting the specifications above will work with your console and assumes no responsibility for the selection, performance or use of third-party products

About M.2 SSD heat-dissipation
The M2 SSD that can be used with this device has a fast transfer speed and is therefore subject to reaching high temperatures If the M2 SSD does not include a heat-dissipation mechanism, attach a heat conductor, such as a heat sink, a heat transfer sheet, or both For information on how to attach the heat conductor, refer to its manual If you use your device without heat-dissipation parts, or the heat-dissipation parts come off during use, the M2 SSD may overheat, and continued use may cause operation failure

Install or remove an M.2 SSD
Safety warnings
Before installing or removing an M2 SSD, please read the following safety precautions

⚠ Caution

• Keep out of reach of young children Young children may swallow small parts which may inflict injury
• When turning on your console, make sure the cover and expansion slot cover are installed correctly If the cover and expansion slot cover are not installed correctly, it may cause the main unit to overheat

Notices

• Before proceeding with the installing or removing process, touch a metal-grounded object to remove any static electricity from your body Failure to do so may cause damage to an M2 SSD or PS5 console In particular, an M2 SSD uses parts sensitive to static electricity, so please use caution
• Do not touch the terminal of an M2 SSD or your PS5 console’s expansion connector
• When attaching or removing screws, use a screwdriver that matches the sizes of the screws If the sizes do not match, the screw may become stripped
• Be careful not to drop small parts such as screws and spacers in the main unit of your PS5 console If small parts do fall in the main unit, do not turn on the power, and instead consult the support website (page 19)

Install an M.2 SSD Place your console on a soft cloth spread over a flat surface before installing the M2 SSD

1. Remove the △ cover (page 7).
   For safety warnings or details about removing or attaching covers, see “Remove and attach covers”
   (Console with the disc drive installed)

2. Remove the screw from the expansion slot cover and then remove the cover.

3. Remove the screw and spacer, and then adjust the spacer to the size of the M.2 SSD.

4. Holding the edge of the M.2 SSD, align it with the notch on the expansion connector. Tilt the M.2 SSD diagonally upward, and firmly insert it all the way into the expansion connector.
   The following shows an M2 SSD with a heat sink and heat transfer sheet attached.

5. Tilt the M.2 SSD down and fasten it with the screw.

6. Attach the expansion slot cover and fasten the screw.

7. Attach the △ cover (page 7).

8. Attach the feet, connect the AC power cord and cables, and then turn on the power. When your PS5 console turns on, the formatting guide appears Follow the on-screen instructions and format the M2 SSD

• Consult our support website if you lose parts such as the expansion slot cover, screws, and spacers (page 19)
• For information about how to save your game data on M2 SSD storage and the types of data you can save, see the User’s Guide (page 19)

Remove an M.2 SSD
Place your console on a soft cloth spread over a flat surface You can then remove the M2 SSD

1. Remove the cover (page 7).
2. Remove the screw from the expansion slot cover, and then remove the cover.
3. Remove the fastened M.2 SSD screw.
4. Slightly lift up the M.2 SSD, and then hold the edge and pull diagonally upward.
5. Fasten the screw back on the spacer.
6. Attach the expansion slot cover and fasten the screw.
7. Attach the cover (page 7).

Attach or remove the disc drive

If you have purchased a console without a disc drive installed, attach the disc drive (sold separately) to play disc-based games, Blu-rayTM discs and DVDs

Caution
Before attaching or removing the disc drive, please read the following safety precautions

Notices

• Before attaching or removing the disc drive, touch a metal-grounded object to remove any static electricity from your body Failure to do so may cause damage to the disc drive or PS5 console
• Do not touch the terminal of your disc drive or your PS5 console’s corresponding terminal

Attach the disc drive
Place your console on a soft cloth spread over a flat surface before attaching your disc drive

1. Remove the cover (page 7). For safety warnings or details about removing or attaching covers, see “Remove and attach covers”

2. Align the disc drive’s clips with the 2 holes (marked with ▼ ), and then firmly push in until you hear a “click”.

3. Attach the cover (page 7).
   Make sure to attach the cover for consoles with the disc drive installed

4. Attach the feet, connect the power cord and cables, and then turn on the console. Make sure to attach the feet for consoles with the disc drive installed

Remove the disc drive
Place your console on a soft cloth spread over a flat surface before removing your disc drive

1. Remove the cover (page 7). For safety warnings or details about removing or attaching covers, see “Remove and attach covers”

2. Use your finger to lift up the concave part of the disc drive and remove it.
   

3. Attach the cover (page 7). Make sure to attach the cover for consoles without a disc drive installed

4. Attach the feet, connect the power cord and cables, and then turn on the console. Make sure to attach the feet for consoles without a disc drive installed

Use and handling

Never disassemble or modify the console or accessories
Use the console and accessories according to the instructions in the product documentation No authorisation for the analysis or modification of the console or accessories, or the analysis and use of its circuit configurations, is provided Unauthorised modification of the console or accessories will void your warranty There are no user serviceable components inside the console Additionally, there is a risk of exposure to laser radiation as well as to electrical shock

Network

• An internet connection is required to connect to a network
• You are responsible for internet service fees For details, refer to the information provided in your service contract or contact your internet service provider
• Use only an Ethernet cable compatible with 10BASE-T, 100BASE-TX or 1000BASE-T networks Do not use a cord for a standard residential telephone line or cables of types other than those mentioned here Using the wrong type of cord or cable can cause more electrical current than necessary to flow through the LAN port, which may lead to heat build-up, fire or malfunction

Wireless networking feature

• The frequencies used by the wireless networking feature of the product are the 24 GHz (WLAN, Bluetooth®)/5 GHz (WLAN) ranges The 24 GHz range of radio waves is shared by various devices The product has been designed to minimise the effect of other devices using the same range However, in some cases, interference from other devices may reduce the connection speed, shorten the signal range, or cause the connection to be terminated unexpectedly
• When using the console scan function to select a wireless LAN access point, access points that are not intended for public use may be displayed Only connect to an access point that you are authorised to use, or one that is available through a public wireless LAN or hotspot service

Handling the controller

• Charge in an environment where the temperature range is between 10 °C and 30 °C Charging may not be as effective when performed in other environments
• The battery has a limited lifespan Battery duration will gradually decrease with repeated usage and age Battery life also varies depending on the storage method, usage state, environment and other factors
• When the controller is not used for an extended period of time, it is recommended that you fully charge it at least once a year in order to maintain battery functionality

Care instructions
For safety reasons, before cleaning the console or connected accessories, disconnect the AC power cord from the electricity supply

Exterior surfaces (plastic cover of console and controller)

• Wipe down with a soft, dry cloth
• To prevent the surface of your console or peripherals from changing colour and quality, follow the guidelines below
  – Do not spray with or apply insecticides or volatile substances, including paint thinner, benzene, or alcohol. Do not wipe with chemically treated cloths.
  – Do not rest or store your controller or headset on top of your console.

Vents
Do not block any vents To maintain good ventilation, follow the guidelines below:

• Place the console at least 10 cm away from a wall surface
• Do not place on a carpet or rug with long fibres
• Do not place in a narrow or cramped space
• Do not cover with cloth
• Do not allow dust to build up on the vents Use a cleaning tool such as a handheld vacuum cleaner to remove dust buildup It is also recommended to remove the covers, and then use a handheld vacuum cleaner to remove the dust trapped underneath For details on covers, see “Remove and attach covers” (page 7)

Ports/connectors
Do not use ports/connectors on the console if they are dirty They may not conduct electricity properly When they are dirty, wipe them with a dry cloth

Disc handling (Only for consoles with a disc drive installed)
Note on compatibility
Some media may have region or territorial restrictions and may not work with your console See media packaging for details

Handling
Fingerprints, dust, dirt or scratches on the disc can distort the picture or reduce sound quality Please note the following

• Do not touch the disc surface when handling a disc
• Do not stick paper or tape onto discs and do not write on discs

Storage

• Do not expose discs to high temperatures, high humidity or direct sunlight
• When discs will not be used for an extended period of time, store them in their cases Stacking uncased discs or storing them at an angle can cause them to warp

Cleaning method

• Clean discs with a soft cloth, lightly wiping from the centre outwards
• Do not use solvents, record cleaners, anti-static spray or other chemicals as these can damage the discs

End of life product recycling
The products are made of many materials that may be recycled The controller contains a lithium-ion battery Follow local regulations when disposing of the products

Specifications

Design and specifications are subject to change without notice Depending on the software version in use, the console may operate differently than described in this manual.

PlayStation®5 console

1 A portion of the SSD capacity is reserved for use in connection with console administration, maintenance and additional options As a result, the availability of SSD capacity may vary
2 Usability of all connected devices is not guaranteed
*3 Use the included HDMI cable

DualSense® wireless controller

Disc drive (Only for consoles with a disc drive installed)

1 PlayStation® format software, PlayStation®2 format software, and PlayStation®3 format software cannot be played from a disc
2 Some functionalities available on PS4TM may be absent when played on PS5 Your PS5 may need to be updated to the latest system software Internet connection required
*3 Playback of BD-RE ver 10 discs is not supported

Region codes
Depending on the disc, a region code that is based on the geographic region where the disc is distributed may be assigned The DVD region code is set to the code of the DVD played for the first time The region codes set on the console are as follows

Notices

• You can change the BD/DVD region code of your console to the disc played You can change the region code up to four times · DVD discs that have not been finalised cannot be played

• Do not use the following discs If you do, the console may be damaged
  – 8 cm discs
  – Non-circular discs, such as discs in the shape of a card, star, or heart
  – Discs that are cracked or deformed, or discs that have been repaired
  – Discs with paper or stickers on them

• A DualDisc features one side that conforms to the DVD standard, and another side with audio only The audio-only side cannot be played on the console

• When playing discs with content that was copied fraudulently, abnormal sounds may be produced or the content may not play correctly

• For continuous playback of copyright-protected BDs, the encryption key for AACS (Advanced Access Content System) may need to be renewed The encryption key is automatically renewed if the console is connected to the internet

• Some discs may not be playable due to scratches, dust, the quality of recording, or the characteristics of the recording device

• In rare instances, BD and DVD may not operate properly when played on the console This is primarily due to variations in the manufacturing process or encoding of the software

System software
Use of this PlayStation®5 console means acceptance of Sony Interactive Entertainment Inc’s system software licence agreement Refer to docdlplaystation.net/doc/ps5-eula/ for further details
If you cannot update over the internet, you can also use a game disc or USB drive For details, visit playstation.com/help/
By updating the system software of the PS5 console, you can enjoy additional features, improved usability, and enhanced security Always update to the latest version

Compliance information

This equipment has been tested and found to comply with the limits set out in the EU RE Directive and UK RE Regulation Only use cables that are either a) supplied with the equipment, b) official PlayStation accessories or c) less than 3 metres in length
This product has been manufactured by or on behalf of Sony Interactive Entertainment Inc, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan
Imported into Europe and distributed by (except the UK) Sony Interactive Entertainment Ireland Limited, 2nd Floor, 2/3 Rogers Lane, Dublin 2, Ireland
Inquiries related to product compliance in the EU should be sent to the manufacturer’s authorised representative, Sony Belgium, bijkantoor van Sony Europe BV, Da Vincilaan 7-D1, 1930 Zaventem, Belgium

RE Directive “Informal DoC” statement
Hereby, Sony Interactive Entertainment Inc, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU For details, please access the following URL: https://compliancesonyeu
This radio equipment is intended to be used with the approved version(s) of software that are indicated in the EU Declaration of Conformity The software loaded on this radio equipment is verified to comply with the essential requirements of the Directive 2014/53/EU and Regulation SI 2017 No1206 The software version can be found via: Select Settings ⚙ > System > System Software > Console Information
Wireless frequency band and maximum output power:
­ Bluetooth® 24 GHz: less than 10 mW
­ WLAN 24 GHz: less than 100 mW
­ WLAN 5 GHz: W52/W53/W56: less than 100 mW, W58: less than 25 mW
This radio equipment was evaluated as receiver category 1 defined in EN 300 440 V211 The following restrictions of use apply in the countries listed in the table below

Operation in the 5150-5350 MHz band is restricted to indoor use only Installations in road vehicles, trains and aircraft are not permitted for 5250-5350 MHz band

Product Ecodesign
For resource and energy efficiency information related to the EU Ecodesign requirements of the Regulation (EU) No 801/2013 and also the European Union Self-Regulatory Initiative to further improve the energy efficiency of Games Consoles (recognised under COM(2015) 178 final report of the European Commission), visit the following URL: playstation.com/Ecodesign For resource and energy efficiency information related to The Ecodesign for EnergyRelated Products and Energy Information (amendment) (EU Exit) Regulations 2019 and also the UK Games Console Voluntary Agreement, visit the following URL: playstation.com/Ecodesign
Product disposal

Where you see either symbol on any of our electrical products, batteries or packaging, it indicates that the relevant electrical product or battery should not be disposed of as general household waste in the EU, UK, Türkiye, or other countries with separate waste collection systems available To ensure correct waste treatment, please dispose of them via an authorised collection facility, in accordance with any applicable laws or requirements Waste electrical products and batteries may also be disposed of free of charge via retailers when buying a new product of the same type Furthermore, within the UK and EU countries larger retailers may accept small waste electronic products free of charge Please ask your local retailer if this service is available for the products you wish to dispose of In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste This symbol may be used on batteries in combination with additional chemical symbols The chemical symbol for lead (Pb) will appear if the battery contains more than 0004% lead This product contains a battery which is permanently built-in for safety, performance or data integrity reasons The battery should not need to be replaced during the lifetime of the product and should only be removed by skilled service personnel To ensure the correct waste treatment of the battery, please dispose of this product as electrical waste

Copyright and trademarks

“ “, “PlayStation” “, “PS5”, “PS4”, “DualSense”, “DUALSHOCK” and “PlayStation Shapes Logo” are registered trademarks or trademarks of Sony Interactive Entertainment Inc

“SONY” and ” ” are registered trademarks or trademarks of Sony Group Corporation

AMD, Radeon and Ryzen are trademarks of Advanced Micro Devices, Inc

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc and any use of such marks by Sony Interactive Entertainment Inc is under license Other trademarks and trade names are those of their respective owners

“Blu-ray DiscTM”, “Blu-rayTM” and “Ultra HD Blu-rayTM” are trademarks of the Blu-ray Disc Association

The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI Trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc

USB-IF SuperSpeed USB Trident logo is a registered trademark of USB Implementers Forum, Inc USB Type-C® and USB-C® are registered trademarks of USB Implementers Forum

All other trademarks are the property of their respective owners

Quick Start Guide
Learn how to set up your PS5 console and how to use basic functions in the included

User’s Guide
Find out about everything your PS5 console can do Learn how to configure settings and how to use each function To see the User’s Guide, you’ll need an internet connection From your PS5 console’s home screen, go to Settings ⚙ > User’s Guide, Health and Safety, and Other Information > User’s Guide

Customer Support Website
Find online support information such as step by step troubleshooting and frequently asked questions by visiting playstation.com/helphttps://manuals.playstation.net/document/en/help_p.html

The information contained in this manual is subject to change without notice
The commercial use or rental of this product is prohibited

© 2023 Sony Interactive Entertainment Europe Limited.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>