BLUESKY B2K Mini Dashcam User Manual

BLUESKY B2K Mini Dashcam

Thank you for choosing your BlueSkySea B2K dash camera. Please read this user manual carefully before using the camera, then keep the manual safe for future reference. Please feel free to contact our customer support team by email if you need any assista nee: support©blueskysea-inc.com

Structure Diagram

1. Indicator Light
2. Menu Button
3. Up Button
4. Down Button
5. OK Button
6. Memory Card Slot
7. MIC
8. Mode Switch
9. Mini USB Interface
10. Reset Button
11. Power Button
12. Lens
13. Speaker
14. Mount Slot

Button and Function Description

Menu Settings Mode

| ****

Menu

| Short press: Exit menu/Back to

previous menu.

---|---|---
Up| Short press: Menu up.
Down| Short press: Menu down.
OK| Short press: Menu confirmation.
Mode| N/A
Power| Short press: Screen Off/On; Long press: Power camera off.

Recording Mode (Wi-Fi enabled)

| Menu| N/A.
---|---|---
Up| N/A.
Down| Short press to switch WiFi on
OK| (If smartphone app is connected) Short press to switch WiFi Off
Mode| N/A

Power

| Short press: Screen Off/On; Long press: Power camera off.

LED Indicators

LEDStatus

| ****

Indication

---|---

Flashing Blue

| Camera in recording mode.

Solid Blue

| ****

Camera in standby mode, not recording.

Voice Event List:

Voice event

| Indication
---|---

“Please insert SD card “

| NomicroSD memory card detected – please insert one.

” BEE- BEE- BEE”

| MicroSD memory card writing speed too slow, please replace with a higher speed card, class 10 or above .
Under non-loop recording mode, the camera has detected card memory is full, please format the card or change to an empty card.

SanDisk Ultra Al Card is recommended

“lock file”

| Thecamera has locked the current video clip due to the lock button being pressed or a G-sensor activation.

Basic Operation

Power on/off:

1. The camera will power on automatically shortly after the ignition is switched on.
2. The Camera will power off automatically when ignition is switched off.
3. For manual power on/off, press and hold the Power button for 5 seconds.

Start recording:

1. The camera will start recording automatically shortly after the ignition is switched on. The Blue LED indicator light will flash while actively recording.
2. Short press the OK button to start recording manually when in Standby mode.

Stop recording:

1. The camera will stop recording automatically when the ignition is switched off.
2. Short press the OK button to stop recording manually when in recording mode.

Take a photo:

1. In recording mode: Short press the “OK” button to stop recording.
2. Short Press “Mode” to enter the photography mode.
3. Short Press “OK” button to take a photo.
4. Short press “Mode” to exit the photography mode.

Lock video clip:

1. In recording mode: Short press the “UP” button to lock a video clip manually. This will lock the currently recording video file with 30 seconds length.
2. Video clips will be locked automatically when the G-sensor is triggered. The sensitivity of the G-Sensor can be adjusted in the settings by pressing the “Menu” button.

Video playback

Playback on camera:

1. Press OK button to stop recording.
2. Short press the Mode button to enter Photo or Video Playback mode.
3. Short press Up or Down button to select a video recording, and then press the OK button to playback the selected video or photo.

Playback on PC:

1. Remove the microSD card and Connect to the computer USB socket via a microSD card reader. Once connected, open a file browser and navigate to the SD card.
2. There will be three file folders when you access the memory card on the computer: a MOVIE (Normal loop recording video files) folder, a EMR (Locked video files) video folder and a PHOTO (Video snapshot files) folder.

You can obtain information from the video file name, for example: 20200412171504_000001.MP4
20200412171504 000002.MP4
20200412171504″ indicates date and time

“000000” “000001” indicates video serial numbers
“EMR” file folder contains any videos that have been locked.
“mp4” is the video file extension (type of file).

Menu Settings:

Resolution: Sets the video mode resolution.
Default 2K resolution; 4K and 1080P, 720P resolution optional!

Loop Recording: Off I 1 I 3 I 5 I 10 minutes.
Selects the loop recording file length.
Once the microSD card is full, the camera will automatically replace the oldest files with new files in a loop to allow continuous

Note that locked files are protected and will not be replaced, you must manually clear them off the microSD card when they are no longer required to avoid the card filling up with only locked files. To avoid the card filling up and thus preventing new recording, this option can be turned off.

WDR (Wide Dynamic Range): Off I On
Dynamic range is the ratio of the brightest portion of the image to

WDR enables the camera to record more details in the shadows while not over- exposing the bright areas. The downside is reduced contrast, the image may look less natural but records more information.

Exposure Comp : -2.0 to +2.0 default 0.0
Adjusts the value of the EV (Exposure Compensation), making the image darker or brighter. This may be useful if the automatic exposure is affected by the front of your vehicle being particularly bright or dark.

Record Audio: Off I On
Turns on/off the microphone (Mute).

Date Stamp: On I Off
Overlay the time and date on the recorded video.

Date/ Time: Set system date, time and date/time display layout.
Use Up or Down buttons to set each character, Press OK button to move to the next character, and press the Menu button when complete.

Car Number: Overlay the vehicle license plate number on the recorded video footage to identify which vehicle recorded the video.
Use Mode button to edit the car Numbers, pre•• Up or Down button• to set each character, Pre•• OK button to move to the next character, and pre•• the OK button when complete.

Frequency: 50Hz I 60Hz
This option should be set according to the power supply specification used in your country or geographical region. for example, USA users should select 60HZ, Europe SO Hz.
Choosing the correct value will reduce flickering caused by incandescent/fluorescent lamps at night time. LED traffic lights may still flicker as these use different frequencies.

Beep Sound: On I Off.
Controls all buttons notification sounds, if you set Beep Off, then you can still hear the voice prompt warnings. Voice prompt warnings are useful to notify the driver of microSD card errors, missing microSD card etc.

Format: Formats the microSD card ready for use with the camera.

Warning: This operation will delete all existing data on the micro SD card, including locked files and normal looping recording files1 Make sure you back up any important files first.

Default Setting: Resets all settings to the factory default settings.
Version: Displays the version number of the currently installed firmware.

Parking mode: Off I On
(Only works with optional hardwire kit connected)
When the engine is turned off, the camera will enter parking mode and stop recording, if an impact is detected by the G-sensor then the camera starts video recording again automatically to record the incident. The whole event footage (Before and After the event)with 30 seconds length will be saved in the memory card!
Note: The hardwire kit is not a standard accessory for the B2K camera, it must be purchased separately.

Notes:
Easiest method for setting the time is to use the smartphone app to synchronize the camera time with your smartphone.

G-Sensor: Off I Low I Middle I High Sensitivity, default: Middle The G-sensor measures shock forces and locks the current video file automatically when the set threshold is exceeded. The settings from “low” to “high” determine the amount of force needed to lock the file.
Note: Locked files must be manually deleted periodically to prevent the microSD card filling up with locked files.

Motion Detection : Off/On
Motion detection is the process of detecting a change in the position of an object relative to its surroundings or a change in the surroundings relative to an object. Camera only takes recording after it detects an object moving.
It will cau11e non-looping recording if you enable the motion detection function;

Timelapse Record: Off /On
Time-lapse photography is a technique whereby the frequency at which film frames are captured (the frame rate) is much more spread out than the frequency used to view the sequence. When played at normal speed, time appears to be moving faster and thus lapsing.
This dash cam applies for lfps photography,an image of a scene was captured at 1 frame per second.
It will cause non-looping recording if you enable the motion detection function;

Screen Save: Off I 1 I 3 Minutes Default 1 Minute
The LCD screen turns off if not used for this time period, if Screen Save is set to Off then the LCD screen will always be on. Having the screen turn off will avoid distracting the driver unnecessarily, especially at night.

WIFI Switch On/Off:

1. In recording mode or in standby mode, press “down” button to switch WIFI function On.
2. The Camera screen will display the Wi-Fi SSID and Password required by your smartphone: SSID: NVT-CARDVXXXXXXXXXX PWA2:12345678
3. If there is no Wi-Fi connection with your smartphone after SSID broadcasting, short press the Up or Down or OK buttons to disabled Wi-Fi.
4. If Wi-Fi is connected with your smartphone, you need to press the OK button to disable Wi-Fi.

Smartphone APP Operation:

APP Download:

• IOS users: Search for Road cam in the APP Store.
• Android users: Search for Roadcam in the Google Play Store.

WIFI Connection:

1. Long press the down button to switch on Wi-Fi. (Once the Wi-Fi is on, the Wi-Fi status icon, SSID and password appear on the camera LCD screen.)
2. Enter the smartphone WLAN(Wi-Fi) settings menu, select the B2K dash camera SSID: NVT _CARDVxxxxxxx and enter the password 12345678 to continue.
3. When the camera is connected with your smartphone, your smartphone MAC address will list on the camera screen
4. Open the App Road cam, Click the “camera” icon to connect the dash cam B2K to the APP.
5. When the camera’s Wi-Fi is disconnected with your phone, and display “Mobile Phone not connect” on the camera screen.
6. Long press the Down button to disable Wi-Fi function on camera. The Wi-Fi icon will be locked, and camera will be back to standard video recording mode automatically.

APP Control:
In the APP Preview mode, press “video recording” button to start/stop video recording;
In the APP Preview mode, press “photo snap button” to capture photo; In the APP Preview mode, press the menu button on the top right corner to enter main menu setup;
In its sub-menu setup, you can set up its resolution; Sound recording On/Off; Video partition 1/3/Smins; G-sensor level Low/Middle/High; Format memory Card etc.

1. Disconnect dashcam
2. Main menu setting
3. Recording time indicator
4. Full-screen display
5. Video playback
6. Photo playback
7. Video recording Recording Start/Stop
8. Switch photo snap

• In the APP Preview mode, press “HUD video” button to playback videos; press “HUD photo” button to view photos;
• Normal looping recording video footages are stored in the loop recording section ,and all locked video footages are stored in the emergency file folder.
• Short press to preview video footage on your smartphone, long press the icon to download/delete video footages on your smartphone.
• In the APP Preview mode, press the Disconnect button in the top left corner to return to the dash camera connection interface.

Mp4 file extension.

Audio| Built in Microphone/Speaker
Memory card capacity| MicroSD card, support 256GB max, SanDisk Ultra Al Card is recom mended . (Not included in package)
Voice indicator| English language voice indicator
WIFI Connection| Supported
G-sensor| Supported
Parking mode| Supported (Hardwire kit not included in packag e) .
Loop recording| Supported: 1/3/5/10 minutes per segment.
Backup power source| Super capacitor (No lithium battery). (Ensures all video is written to memory card on power failure.)
Working temperature| – 20° C- + 70° C
Storage temperature| – 3 5° C – + 7 5° C
Size| 456040mm
Net Weig ht| 50g

FAQ

Under normal operating conditions, if there is a problem with the product, please refer to the following solutions.
Question: Can’t take pictures or video
Solution: Check if the TF card has enough space and if it is locked.

Question: It will stop automatically when recording
Solution: As the HD video data is huge, please use a high-speed TF card compatible with SDHC. The high-speed TF card will have a C4 or C6 logo.

Question: When replaying pictures and videos, a “file error” prompt appears
Solution: An error occurs when the TF card stores data, and the photo files are incomplete. Please use the camera “format” function to reformat the TF card.

Question: The captured image is foggy
Solution: Please check the lens for dirt and fingerprints; before shooting, wipe the lens with lens paper.

Question: When shooting scenes such as sky and water, the image is very dark
Solution: The automatic exposure function of the camera will be affected in scenes with high contrast, which can be corrected by adjusting the “EV” value in the machine setting menu.

Question: In cloudy days and indoor light sources, the color performance is not perfect
Solution: Please check the machine “white balance” function is set to automatic.

Question: There are horizontal stripes in the image
Solution: This is caused by setting the wrong “light source frequency”. Please set it to “SO Hz” or “60Hz” according to the local power supply frequency.

Question: Crash
Solution: After crashing, please short press the reset button to resume and restart.

Question: What memory card is recommended to install?
Solution: SanDisk Ultra Al Card is recommended, SanDisk High Endurance card is not recommended □because the SanDisk High

Packaging Listing

• 1 x B2K HD Dashcam
• 1 x MINI bracket
• 1 x SV 1.5A Car Charger 1 x USB Cables
• 1 x User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>