EXPLORE SCIENTIFIC BCC1001 Portable Bluetooth Speaker Clock with Wireless Charging Instruction Manual
- June 6, 2024
- EXPLORE SCIENTIFIC
Table of Contents
PORTABLE BLUETOOTH SPEAKER CLOCK WITH WIRELESS CHARGING
RADIOSVEGLIA BLUETOOTH CON RICARICA WIRELESS TRAGBARER BLUETOOTH-LAUTSPRECHER
MIT WECKER UND KABELLOSER LADEFUNKTION HORLOGE PORTABLE AVEC ENCEINTE
BLUETOOTH
ART.NO.: BCC1001
ABOUT THIS INSTRUCTION MANUAL
These operating instructions are to be considered a component of the device.
Please read the safety instructions and the operating instructions carefully
before use. Keep these instructions for renewed use at a later date. When the
device is sold or given to someone else, the instruction manual must be
provided to the new owner/user of the product. The device is intended only for
indoor use.
GENERAL WARNINGS
- Risk of electric shock — This device contains electronic components. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.
- Choking hazard — Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
- Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes, and mucous membranes. In the event of contact, rinse the affected region immediately with plenty of water and seek medical attention.
- — Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short circuit, a fire, or an explosion.
- Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
- Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. The batteries should be removed from the unit if it has not been used for a long time.
- Do not submerge the device in water or attempt to disassemble the device.
- Do not use this product in an aircraft.
- The device may be warm while with a power supply through an adaptor. It is normal.
SCOPE OF DELIVERY
Wireless speaker clock, Operating instructions, Micro USB charging cable.
PRODUCT OVERVIEW
-
Press [ > ] to lower volume. While in Bluetooth mode, press and hold to go to previous track.
-
Press [> ] to increase volume. While in Blue- tooth mode, press and hold to go to the next track. Remarks: While in Aux-in mode, the track could only be changed through your device.
-
When playing music, press [>II ] to pause or play. When you receive a call, press to answer or press and hold to reject the call. When you are on the phone through Bluetooth
mode, press to end. When the call ends, the music will resume playing. At Bluetooth mode, press twice to dial a number of the last call. -
Press [M ] to switch mode. Press and hold to enter or exit the standby status.
-
Press [L ] to switch settings between screen brightness, clock, alarm 1, and alarm 2.
-
While in setting mode, press [< ] to decrease brightness or numbers.
-
While in setting mode, press [ >] to increase brightness or numbers.
-
Wireless charging location.
-
Wireless charging indicator Green: wireless charging in progress.
-
LED indicator Red: Speaker in turned on. Off: Speaker off / Standby.
-
Power on/off
-
DC input 5V ….1.5A
-
Auxiliary Line-in Port
-
USB Charging Port – Output 5V 1A
BUTTON MODE|
<<
|
|
II
|
Μ
|
L
|
<
|
---|---|---|---|---|---|---|---
Standard mode| PRESS| Decrease volume| Increase volume| Play or cause answer
or end callSRedial (Press twice)| Switch between AUX and Bluetooth mode Stop
the alarm| Switch setting between screen brightness, clock, alarm 1 and
alarm2|
__
|
__
HOLD| Previous track| Next track| Reject call disconnect Bluetooth connection|
Enter or exit the standby status| | |
Brightness setting mode| PRESS| | | ****| | | Decrease| Increase
HOLD| | | | | | |
Time setting mode| PRESS| | | __| | __| Decrease| Increase
HOLD| | | | __| Go to the next parameter| |
Alarm setting mode
| PRESS| | __| | | | Decrease| Increase
HOLD| | | | __| Go to the next parameter| | __
LCD DISPLAY
1. Time/alarm time display [ BT] Bluetooth signal
[ ] Alarm 1 ON
[ Z²] Snooze activated
[ ] Alarm 2 ON
[AUX ] AUX mode ON
[USB ] USB
GETTING STARTED
POWER SUPPLY
- Insert the Micro USB Charging cable (included) to the DC 5V input port located at the rear of the unit. Insert the other end into a suitably rated wall outlet.
- Push the Power switch to the ON position to turn on the device. The time will be displayed.
- Press and hold the [ M] to enter or exit standby status.
NOTE: To turn off the device and the screen, push the Power switch to the
OFF position.
INTERNAL BATTERY
The speaker contains 2 sets of 2200mAh batteries in the speaker. When fully
charged, the speaker can operate without a power supply and become portable.
NOTE: The charge time is around 3 hours.
WIRELESS CHARGING
1. Place the equipment to be charged on the top circle of the stereo.
2. Device will now start charging.
NOTE: Please make sure your device supports wireless charging.
USB CHARGING
1. To charge a device, connect with a USB charging cable to this USB charging
port [ USB ] at the rear.
2. Device will now start charging.
NOTE: When using wireless charging and USB charging at the same time, USB
charging would be disabled for the purpose of keeping the maximum output
capacity within a safe level.
PLAYING MUSIC
PAIRING / DISCONNECTING VIA BLUETOOH
- Place your device nearby. Press the [M ] till the [ BT] flashes.
- Search for Bluetooth according to your device’s instructions.
- The speaker is named “BCC1001”, enter the PIN “0000” if needed.
- The speaker will beep when complete pairing. The [ BT] stays on.
NOTE : To disconnect the Bluetooth, press and hold [ >II].
AUX
1. Plug the 3.5mm audio cable into the audio input connector and
automatically switch from Bluetooth mode to AUX mode. To switch the mode
manually, press [M ] to switch between AUX and Bluetooth mode.
2. Unplug the 3.5mm audio cable from AUX and the speaker returns to Bluetooth
status automatically.
BRIGHTNESS ADJUSTMENT
- Press [ L] once, all icons will flash.
- To set the brightness of the display, short press [ < ] or [ >].
- Wait for 3 seconds. The brightness you set would be saved automatically and exit brightness setting.
CLOCK
SET AUTOMATICALLY
The time will be automatically adjusted by the Bluetooth connection of an
iPhone.
NOTE : Not applicable to Android phones.
SET THE CLOCK MANUALLY
- Press [L ] twice to enter time setting mode.
- The setting parameter will flash.
- Press and hold the [L ] button to confirm the setting and enter to the next parameter.
- Press [ < ] or [ >] to set the required data.
- Sequence of setting: Hour -> Minute -> 24Hr/12Hr
- If there is no action in 3 seconds, the setting will be saved and will exit the setting mode.
ALARM
SETTING / ADJUSTING ALARM TIME
- Press [ L] triple to enter alarm 1 setting mode. The [ ] will be on. (Press four times to enter alarm 2 setting mode. The [ ] will be on.)
- The setting parameter will flash.
- Press and hold [L ] button to confirm the setting and enter to the next parameter.
- Press [ < ] or [ >]to set the required data.
- Sequence of setting: Hour -> Minute -> Alarm OFF/ON
- If there is no action in 3 seconds, the setting will be saved and will exit the setting mode.
OPERATION
- At the set time, the alarm signal rings.
- The alarm lasts 1 minute.
- To stop the alarm, press [M ].
- During the alarm, press any other button to delay the alarm by 5 minutes.
- The alarm will start again at the next alarm time unless you switch off the alarm function.
NOTE:
a. The alarm will automatically turn off after 4 times of snooze.
b. The screen will be turned on when the alarm rings during Power OFF.
SPECIFICATIONS
Dimensions (Main unit): 204x79x109mm (LxWxH)
Weight (Main unit): 820 g (Exclude batteries)
Power: Micro USB charging cable, DC 5V, 1.5A
Bluetooth standard: 5.0
Output Power: 5W 2
Batteries: 2200mAh2
Wireless Charging Power: 5W
Output Voltage: 5V
Output Current: 1A
EC DECLARATION OF CONFORMITY
Hereby, Explore Scientific GmbH declares that the equipment type with part
number: BCC1001 is in compliance with Directive: 2014/53/EU. The full text of
the EU declaration of conformity is available at the following internet
address:
www.bresser.de/download/BCC1001/CE/BCC1001_CE.pdf
RCM DECLARATION OF CONFORMITY
**The product complies with electrical safety, EMC, and radio spectrum
regulatory requirements for products supplied to the Australian or New Zealand
market.
NOTES ON CLEANING**
• Remove the batteries before cleaning.
• Only use a dry cloth to clean the exterior of the device. To avoid damaging
the electronics, do not use any cleaning fluid.
• Protect the device from dust and moisture.
DISPOSAL
Dispose of the packaging materials properly, according to their types, such as
paper or cardboard. Contact your local waste disposal service or environmental
authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per the Directive 2002/96/EC of the European Parliament on waste electrical
and electronic equipment and its adaptation into German law, used electronic
devices must be collected separately andrecycled in an environmentally
friendly manner.
In accordance with the regulations concerning batteries and rechargeable
batteries, disposing of them in normal household waste is explicitly
forbidden. Please make sure to dispose of your used batteries as required by
law — at a local collection point or in the retail market. Disposal in
domestic waste violates the Battery Directive. Batteries that contain toxins
are marked with a sign and a chemical symbol.
1 battery contains cadmium
2 battery contains mercury
3 battery contains lead
WARRANTY & SERVICE
The regular guarantee period is 2 years and begins on the day of purchase. To
benefit from an extended voluntary guarantee period as stated on the gift box,
registration on our website is required.
You can consult the full guarantee terms as well as information on extending
the guarantee period and details of our services at
www.bresser.de/warranty_terms. Would
you like detailed instructions for this product in a particular language? Then
visit our website via the link below (QR code) for available versions.
Alternatively, you can also send an email to
manuals@bresser.de or leave a message on +49 (0)
28 72 – 80 74-220. Please always state your name, precise address, a valid
phone number, and email address, as well as the article number and name.
Number charged at local rates in Germany (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs. Errors and technical changes reserved.
MANUAL DOWNLOAD:
www.bresser.de/download/BCC1001
SERVICE AND WARRANTY:
Errors and technical changes reserved.
Con riserva di errori e modifi che tecniche.
ManualBCC10012020081904
Explore Scientific GmbH
Gutenbergstr. 2 · DE-46414 Rhede
Germany www.bresser.de
service@bresser.de
Explore Scientific LLC
1010 S. 48th Street, Springdale, AR 72762
www.explorescientific.com
References
- art.no
- Bresser | Startseite | Expand Your Horizon mit BRESSER
- Bresser | Startseite | Expand Your Horizon mit BRESSER
- Bresser | Startseite | Expand Your Horizon mit BRESSER
- index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)
- index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)
- Keep Exploring with Explore Scientific Telescopes, Microscopes, & STEM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>