EVOLVEO RoboTrex H6 Robotic Vacuum Cleaner 2 in 1 User Manual
- June 6, 2024
- Evolveo
Table of Contents
- IMPORTANT SAFETY WARNINGS
- PACKAGE CONTENT
- DESCRIPTION
- PUTTING INTO OPERATION FOR THE FIRST TIME – AUTOMATIC CLEANING
- FIRST CLEANING
- TIME SETTING
- SCHEDULE CLEANING
- REMOTE CONTROL CHARGING STATION
- REMOTE CONTROL
- WET MOPPING
- DRY MOPPING
- DESCRIPTION OF THE STATUS DIODES
- DESCRIPTION OF AUDIO SIGNALS
- CHARGING
- BATTERY MAINTANCE
- Power adapter specifications
- TROUBLESHOOTING
- TECHNICAL SUPPORT
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EVOLVEO RoboTrex H6 Robotic Vacuum Cleaner 2 in 1 User Manual
Dear customer, thank you for choosing the EVOLVED RoboTrex H6. We believe you
will enjoy a lot of fun and happiness.
Please, read the safety rules carefully and follow all common safety rules
before using a robotic vacuum cleaner.
- Read through the instructions for use thoroughly before using.
- Keep the user manual for future reference.
- Follow the rules stated in this manual to reduce the risk of damage to the robotic vacuum cleaner and possible injury.
IMPORTANT SAFETY WARNINGS
This device is a complex electromechanical device, please, pay attention to the following guidelines:
- The device is intended for indoor use at room temperature only.
- Use the vacuum cleaner as often as possible for the maximum cleaning effect.
- Use only accessories provided by the authorised manufacturer. Using non-original accessories can cause damage the robotic vacuum cleaner, electric shock, or fire.
- Do not touch any of the parts plugged into the mains if you have wet hands.
- Do not leave the appliance in the presence of children without supervision of an adult.
- Do not allow children to use the robotic vacuum cleaner even under the supervision of an adult.
- Only use original accessories designed for this model.
- Do not sit on the robotic vacuum cleaner or place other objects on it.
- Do not use the appliance if the power cord is damaged.
- Do not open or repair the unit, there is a risk of electric shock and loss of warranty.
- Do not use the device if you have wet hands or feet.
- Keep away from flammable and volatile substances.
- Do not use the device near objects containing liquids, the device may for example turn the objects over causing water spillage.
- Do not wash the vacuum cleaner with water
- Avoid radiant heat on the plastic surface of the device.
- Do not use the device in a too hot, dusty or damp environment.
- Do not let the device vacuum fluids, burning cigarettes, splinters and sharp objects, matches and other combustible substances, flour, cement, plaster, larger pieces of paper, plastic bags, or other objects that can cause damage to the vacuum cleaner.
- Electrostatic charge may occur during the cleaning process, which may be dangerous to the user
- Also inform your roommates about the use of the vacuum cleaner to avoid possible injury.
- Do not use the robotic vacuum cleaner if its dust container is full.
- The manufacturer and distributor for the European Union is not responsible for damage caused by the operation of the device such as injuries, scalding, fire, damage to other objects etc.
PACKAGE CONTENT
Carefully check you have unpacked all accessories, we recommend keeping the
original
paper box, user manual and packaging materials for the warranty period.
DESCRIPTION
- Front bumper
- Start/Stop the operation
- Return to the charging station
- Spiral cleaning
- Vacuum cover
- Charging contact
- Left side brush
- Battery cover
- Left wheel
- Front wheel
- Right side brush
- Intake opening
- Right wheel
Bottom cover
Product Overview
- Top cover
- Trash container
- Main switch (ON/OFF button)
- Primary filter
- Trash container door
- HEPA fiter
- HEPA fiter frame
PUTTING INTO OPERATION FOR THE FIRST TIME – AUTOMATIC CLEANING
-
This is the most common way of cleaning.
-
Insert the batteries into the remote control, make sure the polarity is correct.
-
Connect the charging station to an electrical outlet with a 230 V power adapter.
There must be no obstacles within 2 meters in front and 1 meter on the sides from the charging station. The charging station must be placed on a flat surface, we also recommend to fix the station to the wall or floor with a double-sided adhesive tape. Place the power cord so it does not get entangle in the cleaning brushes of the vacuum cleaner.
You can also plug the 230 V power adapter directly into the vacuum cleaner. -
Check that the “Main Switch” on the robotic vacuum cleaner body is in the “On’ position.
-
Place the vacuum cleaner in the charging station.
-
The vacuum cleaner battery will start charging automatically.
-
Before putting the vacuum cleaner into operation, prepare the room so there are no objects on the floor that may prevent the vacuum cleaner to operate properly (bigger sheets of paper, cables, stickers, small items, inappropriately placed carpet, etc.).
-
Remove the chairs and other larger items so the vacuum cleaner can easily reach inaccessible places.
-
To put into operation, press the “Start Cleaning” button on the remote control or on the top of the device. If the vacuum cleaner is in the standby mode, press it once to wake it up and twice to put it into operation.
-
The vacuum cleaner starts cleaning automatically until the battery is almost empty, then the vacuum cleaner automatically searches for the charging station and starts charging the battery.
-
To pause/stop the vacuum cleaner operation, press the “Start Cleaning” button again.
-
Press and hold the “Start Cleaning” button on the vacuum cleaner for 3 seconds to switch the device into the “Standby” mode.
-
The vacuum cleaner also switches to the “Standby’ mode automatically when it is idle for more than 15 seconds.
-
Press the Return to the charging station button and the vacuum cleaner will return to the base.
-
For spiral cleaning, place the vacuum cleaner on the dedicated location and press the “Spiral cleaning” button on the vacuum cleaner or remote control.
FIRST CLEANING
- Remove all obstacles that can prevent effective cleaning.
- Also remove objects that can damage the robotic vacuum cleaner
- The carpet must be secured so the robot cannot get on it when mopping. If the mopping pad with the water container is installed on the vacuum cleaner, it may interrupt the cleaning process or cause unwanted soaking of the carpet.
- Direct sunlight may cause a reduced sensitivity of the infrared sensors of the vacuum cleaner, please avoid direct sunlight light.
- Black furniture may not be properly detected due to the physical nature of infrared sensors. This may cause a slight impact, which will be reduced by the front bumper.
TIME SETTING
- Press the “CLOCK” button on the remote control to enter the “Time Setting” mode, use the directional buttons to adjust the time (HH:MM).
- Press the “CLOCK” button again to confirm and save the set time. Successful time setting will be confirmed by a beep sound on the vacuum cleaner.
SCHEDULE CLEANING
- The vacuum cleaner will always start cleaning at the set time.
- Press the PLAN’ button on the remote control to enter the ‘Schedule Cleaning’ mode. • Use the directional buttons at the top half of the remote control display (HH:MM) to set the start for the schedule cleaning.
- Press the “PLAN” button again to confirm the set time of the “Schedule Cleaning”.
- To erase the set time, turn the vacuum cleaner off (the main on/off switch). Successful schedule cleaning setting will be confirmed by a beep sound on the vacuum cleaner.
REMOTE CONTROL CHARGING STATION
- Start/Stop the operation
- Schedule cleaning setting
- Spiral cleaning
- Display
- Directional buttons
- Enhanced MAX mode
- Clock setting
- Cleaning along the walls
- Return to the charging station
- Remote control sensor
- Charging contact
- 230 V input
- Charging connector
REMOTE CONTROL
-
The “CLEAN” (l) button
- Start/Stop the operation
- Run the selected mode
-
Directional buttons (5)
Button : to increase the time value for the schedule cleaning and time setting
Button : a directional button to move forward
Button MAX (6): to decrease the time value for the schedule cleaning and time setting Button MAX (6): a directional button to move backward
Button MAX (6): When selecting the mode, press “MAX” for enhanced mode.
Button : to switch from setting the minutes to setting the hours for a schedule cleaning and time setting
Button : a directional button to move to the left
Button : to switch from setting the hours to setting the minutes for a schedule cleaning and time setting
Button : a directional button to move to the right -
The “PLAN” (2) button
- Enter the “Schedule Cleaning” mode, use the directional buttons at the top half of the remote control display (HH: MM) to set the start for the schedule
- Press the button again to confirm the “Scheduled Cleaning”.
-
The “CLOCK” (7) button
- Enter the “Time Setting” mode, use the directional buttons (HH:MM).
- Press the button again to confirm the set time.
-
The “HOME” (9) button
- Press to command the vacuum cleaner to search for the charging station and start charging.
-
The “SPIRAL” (3) button
- Press to command the vacuum cleaner to start cleaning in circles – targeted
-
The “PERIMETER” (8) button
- Press to command the vacuum cleaner to start cleaning along the walls.
WET MOPPING
Attach the mopping pad with the mop on the vacuum cleaner, use the four installation holes “M” on the bottom of the vacuum cleaner
- Remove the plastic cover and fill the plastic container with water without any cleaning agents (250 ml maximum).
- Water container opening cover
- Handle for removing the container from the vacuum cleaner
- Opening for moistening the mop
- Water container opening
- Water should slowly drip from the left and right plastic
- Open the vacuum cover, remove the dust container and insert the water container
- The container should be properly inserted into its place in the vacuum
- Close the top of the vacuum
- Press the “Start Cleaning” button to start the wet mopping
- In this mode, the device does not vacuum, only the side brushes
- Water drips automatically, so do not let the vacuum cleaner stand motionlessly in one place with remaining water in the container to prevent water spillage on the
- Do not use the microfiber cloth for mopping uneven surfaces or
- Remove the water container when the mopping is
- Do not charge the battery when the water container is
DRY MOPPING
- To remove fine dust and polish the
- Attach the mopping pad with the mop on the vacuum cleaner, use the four installation
- Do not use the microfiber cloth for mopping uneven surfaces or holes “M” on the bottom of the vacuum cleaner.
DESCRIPTION OF THE STATUS DIODES
Status | LED indicators |
---|---|
Charging | Flashes orange |
Battery fully charged | Shines green |
Selected mode | Flashes green |
Error | Flashes red |
Low battery | Shines orange |
Cleaning mode | Shines green |
DESCRIPTION OF AUDIO SIGNALS
o| The front wheel or the side brushes do not work.| Check the front
wheel and the side brushes and clean them.
---|---|---
o o| Error of the bottom or front sensor.| Clean the bottom sensors;
lightly press the
front bumper. Check there is no jammed object.
The vacuum cleaner got jammed
Move the vacuum cleaner and continue cleaning.
If the problem still occurs, check whether the battery is fully charged if it
is, turn the vacuum cleaner off and on again with the main switch.
CHARGING
If you want charge up the vacuum cleaner, press the “Return to the charging station” on the remote control.
The vacuum cleaner will search for the charging station and automatically start charging the battery
If the battery status is low, the vacuum cleaner will automatically search for the charging station and start charging. Keep the charging station connected to the mains continuously otherwise the vacuum cleaner will not be able to find it.
BATTERY MAINTANCE
- If you are going to carry the robotic vacuum cleaner or not use it for a long time, press the main switch to turn it
- We recommend using the charging station for
The vacuum cleaner is equipped with a special protection that stops charging the battery when it is fully charged so the battery cannot be overcharged. This ensures a long service life of the battery and the vacuum cleaner is always ready to start cleaning
CLEANING THE VACUUM CLEANER
Empty the dust container after every cleaning.
If the dust container is full it has a bad effect on the suction power of the
vacuum cleaner and the quality of the cleaning
Clean the HEPA filter every 14 days with a dust brush. We recommend replacing the HEPA filter every 6 months. If you rinse the dust container with water, let the container dry completely before reassembling the vacuum cleaner.
CLEANING THE SENSORS, CONTACTS AND BRUSHES
Clean the charging contacts on the vacuum cleaner and on the charging station once a month with a soft cloth. Clean the three sensors on the bottom of the vacuum cleaner in the same way.
Check the two side cleaning brushes once a week and remove entangled hair and other dirt. Remove the dust from the air intake.
Power adapter specifications
Device manufacturer’s name, address and commercial registration number| Naxya Limited
No. 5, 17/F, Strand 50, 50 Bonham Strand, Sheung Wan, Hong Kong
1891486
---|---
Device model number| RTX-H6
AC adapter manufacturer’s name or trade mark, commercial registration number
and address| Ten Pao lndustrial Co., Ltd.
Room 10-11, 6/F., Kwong Sang Hong Centre, 151-
153 Hoi Bun Road, Kwun Tang, Kowloon, Hong Kong
AC adapter model identifier| S012DBV1900060
lnput voltage| 100-240 V~
lnput AC frequency| 50/60 Hz
Output voltage| 19V
Output current| 0.6A
Output power| 11.4 W
Average active efficiency| 84.85%
Efficiency at low load (1O %)| 76.32%
No-load power consumption| 0.057W
Percentage of nameplate output current
Load condition 1
| 100%±2%
---|---
Load condition 2
| 75%±2%
Load condition 3|
50%±2%
Load condition 4
| 25%±2%
Load condition 5|
10%±1%
Load condition 6|
0%
Importer
Abacus Electric, s.r.o.
Planá 2, 370 01, Czech Republic
Manufacturer
Naxya Limited
No.5, 17/F, Strand 50, 50 Bonham Strand, Sheung Wan, Hong Kong Made in
China
TROUBLESHOOTING
First read ”FAQ – Frequently Asked Questions” at: www.evolveo.com/cz/robotrex-h6 or contact EVOLVEO Technical Support.
TECHNICAL SUPPORT
The warranty DOES NOT APPLY to:
- using the device for other purposes than it was designed to
- failure to observe the ”Important Safety Instructions” stated in the user manual
- electrical or mechanical damage caused by improper use
- damage caused by natural elements such as water, fire, static electricity, power surges etcetera
- damage caused by an unauthorized repair
- unreadable serial number
- the battery capacity drops after 6 months of using (6-months battery life warranty)
Disposal
The symbol of crossed out wheelie bin on the product, within the literature or on the packaging reminds you that in the European Union, all electric and electronic products, batteries and accumulators must be stored as assorted waste after the end of their service life. Do not throw these products into the unsorted municipal waste.
DECLARATION OF CONFORMITY
Hereby, the company Abacus Electric s.r.o. declares that the EVOLVEO Robotrex H6 is in compliance with the requirements of the standards and regulations, relevant for the given type of device.
Find the complete text of Declaration of conformity at ftp://ftp.evoIveo.com/ce Copyright Abacus Electric, s.r.o.
www.evolveo.com
www.facebook.com/EvolveoEU
All rights reserved.
Design and specification may be changed without prior notice.
www.evolveo.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>