Cassia X2000 Bluetooth Router User Guide
- June 6, 2024
- Cassia
Table of Contents
CASSIA X2000 Bluetooth Router
QUICK START GUIDE
INCLUDED IN PACKAGE
1. X2000 Router (1)
4. Cable Glands (2)
7. Slotted Screwdriver (1)| 2. Pole Mounting Straps (2)
5. USB Hole Silicone Plug (1)
8. Anchors with Screws (2*4)| 3. Extra Top Screw Covers (2)
6. Mounting Bracket (1)
9. Quick Start Guide (1)
---|---|---
HEAD & BASE
MOUNTING & INSTALLATION
Please select the corresponding steps according to your router’s configurations.
1) Install USB Cellular modem inside X2000
Step 1 ：Remove the top screw cover
Step 2：Use a cross screwdriver to open the top cap
Step 3: Connect USB cellular modem to the USB port
Step 4: Install the top cap, tighten the screws and insert the top screw cover
2) Install USB Cellular modem outside X2000
Step 1：Open the top cap
Step 2：Use a slotted screwdriver to remove the USB hole plug (M20X1.5. Please don’t mix with the ETH/PoE plug)
Step 3: Connect USB cable to USB port
Step 4: Pass the USB cable through the USB hole, install the top cap, install the silicone plug-in USB hole, and then connect the USB cellular modem to USB cable
3) Mount the X2000 mounting bracket in a vertical orientation onto a wall or pole with the supplied mounting kit
NOTE: The side of the mounting bracket facing the wall and pole is sharp. Please don’t hurt your hands.
|
---|---
4) Slide X2000 down on the X2000 mounting bracket
|
---|---
5) Connect Ethernet cable and PoE
Remove the ETH/PoE plug (M22X1.5. Please don’t mix with the USB hole plug),
pass the Ethernet cable through the cable gland, insert the RJ-45 connector
into the Ethernet port of X2000, and tighten the cable gland in the order of
a, b, c. The torque of step c should be less than the torque of step a.
NOTE: When removing the cable gland, please follow the order of c, b, a.
Otherwise X2000 will be damaged.
NOTE: In order to remove the Ethernet cable once it’s been installed, please use the supplied screwdriver in the X2000 box or a small pointed tool of your choosing to depress the plastic release tab on the cable. See the image below.
6) Connect 12V DC power cable and cable gland to X2000 in the same way as step 5
7) For outdoor X2000 installations, please connect the ground cable to ensure X2000’s safety
SETUP BLUETOOTH ROUTER
-
Setup using Wi-Fi Hotspot
a. The Cassia Bluetoo th router provides a Wi-Fi hotspot for initial setup. Its SSID is cassia-xxxxxx. The xxxxxx is the last 6-digits of router MAC ID. The default password of the Wi-Fi hotspot is the same as SSID.
b. Power on the Cassia router, search Wi-Fi hotspot SSID on your computer, then connect to the Wi-Fi hotspot.
c. Please open an Internet browser on your computer, then enter the router’s default IP address: 192.168.40.1. The default login is admin/admin. -
Setup using an Ethernet connection
a. Connect the Cassia Bluetooth router to a managed Ethernet switch and access the DHCP table or scan using a port scanning tool to locate the IP address assigned to the router’s MAC ID.
b. Open an Internet browser on a computer that is connected to the same network and enter the IP address discovered above. The default login is admin/admin.
As part of your first login, you will be prompted to change the default password. If you forget your password or can’t find the Wi-Fi hotspot, please reset the router to default settings by pressing and holding the reset button for 10 seconds.
After login the router’s configuration webpage, please follow Router Quick Start Guide in https://www.cassianetworks.com/knowledge-base/general- documents/ to finish the router configuration.
PRODUCT INTERFACE
Bluetooth Low Energy: 4.0/4.1/4.2/5.0
Wi-Fi: 802.11 a/b/g/n/ac, 2.4GHz and 5GHz ISM band
Ethernet: 10/100 Base-T
USB 2.0: supports USB cellular modem
Opt. external Bluetooth antenna connectors: 50 Ohm N type female connector
Reset button: Factory reset. Please remove the reset plug (M12X1.5) first
LED lights: BT/AC/4G/Wi-Fi/Ethernet/System/Power
POWER
Power over Ethernet: 802.3af/at compliant source
Optional: 12V DC power adapter [1] NOTE: Please don’t use two power
sources at the same time
ENVIRONMENTAL
Operating temperature: -40℃ to +65℃ (-40°F to +149°F)
Humidity: 0% to 90% non-condensing
Storage and transportation temperature: -50℃ to +70℃ (-58°F to +158°F)
Wind resistance: up to 85-MPH sustained winds & 135-MPH gusts
IP rating: IP66
For additional assistance, please email:
support@cassianetworks.com
Connector type: Interior diameter 2.5 mm / outside diameter 5.5 mm, center +v
/ outer –v
Output voltage: 12V
Output power: Equal or larger than 12 W
Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
NOTE: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
For additional information, please go to: https://www.cassianetworks.com
RF Exposure Warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
EU Regulatory Conformance
Cassia Networks Inc., hereby declares that Cassia X2000 Series Bluetooth
Router is in compliance with the directives listed below:
EMC Directive 2014/30/EU
Low Voltage Directive 2014/35/EU
RED Directive 2014/53/EU
REACH European Regulation (EC) No 1907/2006
RoHS Directive 2011/65/EU & 2015/863/EU
WEEE Directive 2012/19/EU
A Declaration of Conformity for these directives is available for viewing at
https://www.cassianetworks.com
Cassia Networks, Inc.
https://www.cassianetworks.com
97 E. Brokaw Road, Suite 130, San Jose, CA 95112, USA
support@cassianetworks.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>