JLAB Fit Sport 3 Wireless Fitness Earbuds User Guide

: June 6, 2024
: JLab

Table of Contents

FIRST TIME SETUP: BLUETOOTH PAIRING
RECURRING USE
BUTTON FUNCTIONS
VOICE PROMPTS
CHARGING
FITTING
CABLE CLIP USE
CONNECTION TROUBLESHOOTING
WARNING
CAUTIONS
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

JLAB Fit Sport 3 Wireless Fitness Earbuds

We love that you are rocking JLab Audio!
We take pride in our products and fully stand behind them.

| YOUR WARRANTY
All warranty claims are subject to JLab Audio authorization and at our sole discretion. Retain your proof of purchase to ensure warranty coverage.
---|---
| CONTACT US
Reach out to us at support@jlabaudio.com or visit jlabaudio.com/contact
---|---

REGISTER TODAY
jlabaudio.com/register
Product updates | How-to tips FAQs & more

FIRST TIME SETUP: BLUETOOTH PAIRING

Turn on the Bluetooth in your device settings.
Press and hold button for 10 seconds.

Light will flash red and blue to indicate pairing mode.
Select “JLab BT” in your device settings to connect.
Light will slow blink blue when Bluetooth is paired.

RECURRING USE

Once JLab Fit Sport 3 has initially paired to your device, the earbuds will auto connect to your Bluetooth device when powered back ON.
(Follow BUTTON FUNCTIONS instructions)

BUTTON FUNCTIONS

VOICE PROMPTS

“HELLO”
Power is ON.
“READY TO PAIR”
JLab BT earbuds are ready to connect to your Bluetooth device.
“YOU’RE CONNECTED”
JLab BT earbuds are connected to your Bluetooth device and ready for use.
“GOODBYE”
Power turning OFF.

CHARGING

Open USB door and connect the cable to a computer or USB power source to charge.
Make sure the charging source is rated at 5V or less.
Light will turn solid red when charging and turn blue when fully charged.

FITTING

Choose ear tip size and optional Cush Fin.
Try various ear tips to find the best fit.
Move the earbud to desired location from the Adjustable Tip Placement.
Start from the back + rotate around the ear.
Secure cable in front, back + bottom.

CABLE CLIP USE

Attach the cable clip near the center of the cable.
Clip in the back or front position of shirt.

CONNECTION TROUBLESHOOTING

I DO NOT SEE JLAB BT IN MY DEVICE

Turn Bluetooth off and then back on in device settings
If you still do not see JLab BT, repeat F IRST TIME SETUP: BLUETOOTH PAIRING directions.

JLAB BT DOES NOT RECONNECT TO MY DEVICE AFTER POWERING ON

In device settings, forget the JLab BT.
Turn Bluetooth off then back on in device settings.
Repeat FIRST TIME SETUP: BLUETOOTH PAIRING directions.

BLUETOOTH IS CONNECTING TO AN UNWANTED DEVICE

Note: The JLab BT can remember up to 8 devices. It will try to auto-connect to last device used.

If you have more than one device that was connected to JLab BT, turn OFF Bluetooth on unwanted devices and turn ON Bluetooth on chosen device.
Press and hold button for 10 seconds. Release.

Light will slow blink blue when Bluetooth is paired.

WARNING

Make sure USB door is closed and fastened.
This will protect against sweat and water damage.

Before charging, the Fit Sport 3 earbuds need to be fully dry.
If there is any exposure to moisture, the internal components may become damaged.
It is best practice to air dry before charging.

CAUTIONS

Avoid getting moisture or liquids into the tip of the earbuds or charging port.
Avoid extreme heat, cold, and humidity.
Avoid dropping or crushing the earbuds, stressing the cable by rapid pulling or extreme force, or bending the cable at a sharp angle.
Wax may build up in the earbud tips, lowering the sound quality. Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
If you experience regular discomfort while using this product, discontinue use and consult your physician.
We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.